Budget renovation of a small corridor. Modern renovation in the hallway ideas, photos, useful tips. Renovating the hallway in an apartment: photos, small-sized corridors Corridor, how best to make a renovation
The hallway is the last to be renovated. The main reason is that all construction debris and dirt during the renovation of all other premises will pass through it. Something in it will wake up, fall away, smudge, and what will the face of the house turn into? So, when making more or less serious renovations in an apartment, you should definitely think about renovating the hallway, especially since renovating a hallway with your own hands is not a technically difficult task, and professional, high-quality inexpensive renovation of a hallway is a fairly common service.
Of course, the owners choose whether to do it on their own or not. But keep in mind that due to the small volume and surface area of the room, the cost of the work will be no less than 50% of the total, i.e. When renovating the hallway by outside craftsmen, half of the payment will go to them for the work. So look according to your skills and budget capabilities. If you decide to do it yourself, then first of all you need to know the features of the room.
What to consider?
Hallways, as we know, are mostly small and cramped, with no sources of natural light. Dirt is carried into the hallway; people walk on the floor in stiletto heels, or even skates. They place weights on the floor, sometimes hard and angular. Splashes from umbrellas, clothes, and shaking off pets fly onto the walls in the hallway.
A wave of cold air from the opened door may burst into the hallway, and relative humidity it will immediately jump above the dew point. Condensation may not be noticeable to the eye, but it will remain in the cracks and pores of the finish, and will slowly do its destructive work: rot, mold, all kinds of infection.
But you want to have even a small corridor that is clean, bright, cozy, and not a dark, gloomy passage that immediately spoils the mood of both yourself and your guests. This is quite possible if repair work is carried out according to a clear plan, in a certain sequence and with full knowledge of the matter, especially regarding the choice of materials.
Planning
The general sequence of planning a hallway renovation, in order of importance of the stages, is as follows:
- Lighting;
- Organization of space;
- Surface finishing;
- Flooring;
- Furnishings.
Options for repairing a hallway depend primarily on its original layout with exemplification - calculating the volume of the room, the area of the ceiling, walls and floor separately and the type of layout. The latter largely determines the choice of the nature of lighting, volumetric and surface design, and on them, in turn, depend technological features of the work performed. Therefore, it is advisable to link the description of the repair to the most common types of hallways.
Types of hallways
IN standard houses The layout of hallways can be roughly divided into the following types:
- Box;
- Corridor;
- “Nora with a Snatch”;
- Coupe.
The box hallway is typical for brick Khrushchev apartments: from a small (about 4 sq. m.) kennel doors lead to the bathroom and living rooms; perhaps also for the kitchen, if the house was originally built for the “comrades” of the nomenklatura, i.e. superiors. “Boxes” are found both in Stalinist buildings and in modern houses. Repairing a small hallway of this type is the easiest; The most troublesome thing is the furniture - because of the doors on all the walls it is very difficult to install a standard wardrobe.
The hallway-corridor is most often found in panel house. The corridor is often narrow and long, so its decoration is of particular importance as a way of organizing space. Repairing a simple corridor is of medium complexity. The hallways, box and corridor are shown in the picture.
“The hole with the snatch” is an indispensable part of the Khrushchev block: a narrow corridor past the nursery to the living room (hall) with a branch past the bathroom to the kitchen. The design of the renovation is quite complicated: narrow, cramped, how to organize the space if there is only a little of it? It is still possible to do it decently, if you take into account the orientation of the apartment to the cardinal points, see the corresponding section.
Note: they began to call the living room a hall just during the second wave of Khrushchev’s housing construction, which was marked by the fight against architectural excesses and the appearance of panel boxes with ceilings of 2.5 m and a total area of up to 11 square meters. m/person.. Etymology – black humor of new settlers.
If you decide to start renovations in the hallway, immediately decide what functions it will perform. Will it be an entrance hall, or a spacious hall without heavy furniture, and only with some decorative elements. Or maybe the area of the corridor is so large that it will be possible to place several useful areas in it at once. Decide on the color of the walls and furniture that you will place here. And also, with quantity and type interior doors, their color and design. Don’t forget about the front door, from which it is advisable to start repairs in the corridor. Floor covering is also very important. Don't lose sight of him.
Renovation in the hallway: ideas, do-it-yourself and necessary materials
A budget renovation in the hallway is what will save the situation after all the rooms in the house have noticeably changed, and the owner of the house’s wallet has noticeably lost weight. There is nothing else left to do but come up with your own ideas and bring them to life yourself.
Do-it-yourself hallway renovation is a great idea for completing the renovation of the house as a whole.
After you have renovated the entire house, you have a large amount of leftovers from various building materials. Don't rush to throw them away. They are perfect for renovations in the hallway. Let your imagination fly and you will be surprised by the result. To design your hallway, whatever you have at hand can suit you.
Materials and accessories for DIY hallway renovations that you can use:
- Remains of linoleum or laminate;
- Paint, whitewash, wallpaper remnants;
- Mirrors, furniture and decorative elements from renovated rooms;
- Dresser;
- Small pouf;
- Desk lamp;
- Floor vase or fresh flowers.
Remember, everything you do with your own hands will save you a decent amount of money, or will be absolutely free. Try to give a set of furniture and materials a basic style, and your hallway will be in no way inferior to expensive, luxurious furniture.
Functional hallway in an apartment: ideas, design photos
The hallway in an apartment is almost always a space in the corridor front door. The hallway is a set of furniture and a room for undressing and storing things at the same time.
The design of the hallway in an apartment depends on the area of the corridor, on the functions it performs, and on the number of people who live in this living space.
The design of the hallway should be chosen so that the hallway is in harmony with the other rooms of the apartment. If you add some design tricks to the standard hallway modules, you will give it a sophisticated and stylish look.
The main types of hallway design in an apartment:
- Open hallway;
- Closed hallway;
- Combined hallway;
- Glossy hallway;
- Entrance hall under the tree;
- Antique style hallways;
- Entrance hall.
When choosing a style for your hallway, make sure that the appearance of the hallway matches the area of the corridor. Consider lighting too. This is very important, because corridors in apartments usually have no windows.
What are the main ideas for the hallway?
The hallway must first of all meet certain requirements - it must be as useful and comfortable as possible. You need to arrange it in such a way that you don’t get annoyed later when you come home and immediately at the door find yourself in chaos, where everyone is crowding, pushing and spreading dirt around the apartment.
Ideas for hallways can be very different. You can equip it in the spirit of minimalism, providing only the most necessary elements, or you can place a large set of household items, and you will get not a corridor with an entrance hall, but a real comfort zone, with furniture for things, relaxation, communication on interests, and care of wildlife.
The most important requirements are that hallways should be practical, free to move around in and comfortable. Whatever color of the hallway you choose, think about whether you can devote enough time to keeping it clean. After all, the hallway, like no other room, requires careful care. Decorate your hallway with various decorative elements and you will give it uniqueness and originality.
When arranging your hallway, you can decorate it with the following items:
- Natural flowers;
- Floor lamp or table lamp;
- Figurines, figurines, candelabra, candlesticks;
- Wicker basket for clothes and shoes;
- Carved mirrors;
- Built-in lighting, lamps, chandeliers.
But try not to “overdo it”; unnecessary items will interfere with your ability to easily and easily use the hallway.
Design solutions and renovations in the hallway: ideas, photos, directions
Designing a corridor is difficult. This is subtle, individual for everyone individual case, Job. Even if the corridors are apartment building are similar to one another, then each home owner, one way or another, makes his own adjustments to its use.
Repairs in the hallway should first of all be carried out taking into account the requirements set by the function of the corridor itself - this is the space between outside world and living space.
All the dirt and dust from the street, raindrops dripping from clothes, or lumps of snow after a snowball fight are always brought into the hallway. Therefore, the main requirement of the materials that you use when decorating the corridor design is that they should be easy to clean.
The main directions for designing repairs in the corridor:
- The walls of the corridor must be made of materials that can be wet cleaned;
- It is best to lay laminate or ceramic tiles on the floor;
- It would be nice to make the ceiling in light colors, and if the height allows, then multi-level with the use of spotlights;
- It is most practical to paint the doors with durable, moisture-resistant paint.
It is best to start renovating a house after the entire house has been renovated and all the pipes have been sealed.
Renovating the hallway: ideas (video)
Believe me, if new building materials are brought in through the renovated corridor and old ones are taken out, then soon your renovation will be “blown away.” The surface of building materials used for repairs should be comfortable and practical. Add a stylish touch to your hallway design idea, and not only your guests, but also you yourself, when you come home, will be surprised every time by the practicality and genius of your interior.
The entrance hall and corridor can well be called the “face of the apartment”, since they form the first impression of the home owners, their tastes and well-being. Therefore, the design of these premises should be thought out carefully, down to the smallest detail.
Finishing the corridor in an apartment is usually done last, since dirt and construction debris during the renovation of other rooms will remain all the way from the front door to the rooms where the work is being done. In addition, if construction materials or large pieces of furniture are brought in, they can easily damage the finish on the walls and floors of the hallway. That is why the cladding of these surfaces is done last.
What needs to be considered when planning the decoration of the corridor?
Hallways in standard city apartments usually have a very small area without a source natural light. Dust and dirt from the street are first brought into these walk-through rooms, since they are often walked on in street shoes.
In addition, you should also think about the fact that during the operation of the apartment, various pieces of furniture and large household appliances will be carried through the hallway and corridor, which during transportation can easily damage the surfaces of the walls. Therefore, for finishing it is recommended to choose materials that have a certain strength.
Another important point that cannot be ignored when planning the renovation of these premises - despite their small area, finishing work can result in a decent amount if they are carried out construction team. Therefore, having really assessed your strengths and financial capabilities, you can try to carry out this stage yourself, choosing an affordable method and materials suitable in quality and price.
In order for the work to be successful, it should be carried out according to a pre-drawn up plan, which should provide for the entire sequence of actions.
Work plan
The stages of repair work for any of the rooms of the apartment practically do not differ in their sequence, but will differ in scale, depending on what type of repair is chosen: major or cosmetic.
- Major repairs include complete dismantling coatings of all surfaces with replacement electrical wiring, arrangement of a new floor screed and a plaster leveling layer on the walls. In addition, the total scope of work may include installation of a suspended ceiling.
- Cosmetic repairs involve replacement decorative coatings walls and floors, and sometimes the installation of a suspended ceiling. If they are produced ceiling work, then you may have to make additional wiring of electrical cables for lighting devices that are built into suspended ceiling.
So, the entire process of performing repair work is usually planned in the following sequence:
- For any type of repair, this means dismantling old decorative coatings and cleaning surfaces, removing all previously completed leveling layers - during a major reconstruction of the premises.
- Carrying out the necessary calculations of the finishing area and the amount of materials required for this.
- Determining the location of lighting fixtures and installing wiring. Its connection to the electrical network is made already at the final stage of repair. It is recommended to entrust work related to electricity to to a professional master, having the appropriate permit.
- Space planning, that is, determining the placement of furniture necessary in the hallway, depending on the size and shape of the room. If it is possible to plan the premises using a special computer application, then this will be the best option, which will allow you to visually evaluate the color combination and convenience of the proposed arrangement of all interior accessories.
- Finishing the ceiling using the chosen method and material - for any type of repair work.
- Leveling the walls and then cladding decorative material at major renovation, or only finishing work for cosmetic transformation of the room.
- Leveling the floor using a screed, and then laying the floor covering, possibly with a heating system - when completely remodeling rooms, or just replacing decorative flooring during cosmetic repairs.
Types of hallway spaces
Lighting and design solutions for the hallway largely depend on the type of hallway and corridor. With a standard layout, these rooms can be combined and have the following forms:
- A “box” is a square or rectangular room that provides ample opportunity for imagination and can be decorated in any style. Such hallways are typical for old-built houses and have an area of 4 square meters. m.
- The hallway-corridor is a narrow, elongated rectangular room, sometimes with smooth turns under different angles, in which it is quite difficult to place a lot of furniture. Therefore, you will have to choose for her only the most necessary things - this could be a shelf for shoes, an ottoman, a hanger for outerwear, and of course a mirror, which you cannot do without in the hallway.
- Hallway “boot” - this type of room also combines in its configuration two corridors located at right angles to each other. In one of them there are doors to the sanitary premises of the apartment, and it leads towards the kitchen, and in the other, in fact, there is an entrance hall with doors to the entrance and to the living quarters of the apartment. As a rule, these two corridors have a small width, but a sufficiently long length along which all the necessary furniture accessories can be installed.
What will be subject to reconstruction and finishing?
Hallway lighting and ceiling
After the walls are cleared of old coatings, it is worth thinking about how to properly distribute lighting in a dark hallway and corridor, since intense lighting is necessary for them. This factor is due to the fact that, as a rule, people perform the final touches to tidy up their appearance when leaving home in the hallway in front of the mirror. For this purpose, it is necessary to ensure that there is enough light in this room, and it is advisable to organize shadowless lighting.
If a small room is dark, it will visually seem even cramped. To avoid this effect, it is recommended to make the ceiling light and install lamps on it that provide bright but diffused light.
If the ceiling is planned to be painted, then the best option for this would be acrylic paint. However, this option will be beneficial only if the surface is perfectly even and smooth, otherwise bright lighting will reveal all existing flaws.
In recent years, suspended ceilings made of plasterboard have become popular, having one or several tiers forming niches into which neon or LED strips or the same lamp is installed. Most often, the tiers are given intricate curved shapes that visually expand the space, making the room look wider. In addition, such a ceiling option will help to illuminate certain areas of the room more intensely, in particular the one where the mirror will be fixed.
If the apartment does not have too high ceilings, then you can use a glossy light stretch ceiling to decorate them. Light from devices mounted on the walls will be reflected on its surface, increasing the overall intensity of lighting. In this case, it is advisable to direct the light from the wall sconces onto a glossy surface.
Original interior solution– two-tier ceiling
If the apartment owner has good skills in working with construction and finishing materials, he will be able to cope with this task on his own. To help him - a detailed publication on our portal
To get an even bright light It is advisable to use modern, economical LED lamps, which today large assortment can be found in specialized stores. Such lamps, with low power consumption, create an excellent level of illumination. Many of them are specifically designed to be built into a plasterboard structure - they look like neat dots, which is why they are called dotted. Lamps that are turned towards the ceiling are equipped with lamps equivalent in luminous efficiency to 50÷60 W. If the sconces will be installed on the walls of a narrow hallway, it is recommended to choose flat models that do not protrude too much from the wall, otherwise they will visually make the room more cramped.
If the ceiling and top part make the walls light, then this factor will increase the overall illumination and help save on energy consumption, since the effects of reflection of the light flux from surfaces are actively “turned on.”
If the ceiling in the hallway is not too high, then you should not use low-lying lamps or chandeliers for lighting, as they will visually make the room even lower.
If you have the financial means, you can install a stained glass suspended ceiling in the corridor, illuminated from the inside. But it should be remembered that in these conditions you should not choose a pattern with a dark color scheme, and to organize the lighting it is better to use lamps with a cool glow.
Except ceiling surface, recessed lamps are sometimes installed in walls if they are covered with plasterboard, which is fixed to a frame made of a metal profile, or are placed in niches.
Drywall prices
drywall
Drywall is the optimal material for leveling walls
If the space of the room allows, then this method becomes the most convenient to implement, and all the work can be done independently. Read more about it in a special publication on our portal.
Hallway flooring
The corridor and hallway are the rooms with the highest intensity of movement of apartment residents. In addition, we must not forget about dirt and dust carried on shoes, which may contain grains of sand that can damage some coatings with their abrasive effect. Therefore, for flooring in these rooms, you need to choose a material that has increased strength.
Most popular floor coverings materials used in apartments are linoleum, ceramic tiles and laminate. Less commonly you can find parquet or solid boards. Each coating has its own characteristics, which you need to know about in order to choose the best option.
Ceramic tile
The range of this material in construction stores is quite wide, but not every type of tile is suitable for a hallway.
You cannot purchase tiles intended for wall cladding for laying on the floor, since they have completely different indicators of strength and wear resistance.
When laying near the front door, you should not choose tiles with an absolutely smooth glossy surface, since if you step on it in wet shoes, you can easily slip and get seriously injured. This factor especially needs to be taken into account if the family has small children or elderly people. If you plan to lay this particular material, then the best option would be to choose tiles with a rough surface - this is usually indicated on the packaging of the material.
In addition, we must not forget that ceramics are a “cold” type of flooring and are best installed on a pre-installed system. Suitable for apartment conditions electric version heating with cable or special mats. These systems are safe to use and consume a minimal amount of electricity.
The advantages of tiles include ease of care, durability and long term operation. However, this material is quite difficult to install, and if there is no relevant experience in this area, then you will have to invite a specialist, and this is also an extra expense.
Tiles can be combined with other floor coverings, such as linoleum, laminate or even carpet. Thus, you can divide the hallway into zones. One of the common options is to lay ceramic tiles near the door, and the rest of the surface of the hallway and corridor is lined with another material. Such a solution will make these rooms less boring, especially if the design of the material is tasteful.
Laminate
Linoleum
Linoleum is traditional flooring material for flooring in all rooms of the apartment, including the hallway, and it can be called time-tested in its practicality. If earlier this type of coating did not differ in variety in base and colors, today its assortment pleases consumers, since it provides the opportunity to choose according to such criteria as material of manufacture, degree of wear resistance, pattern, thickness, color range and, of course, price.
If your financial capabilities allow, you can purchase natural-based laminate.
It meets all the requirements for its use in walk-through rooms - these criteria include environmental friendliness, moisture resistance and strength, high stability to mechanical damage, low thermal conductivity, ease of maintenance and durability. The disadvantage of any natural material is its high price.
Artificial linoleum is produced on the basis of polymer raw materials and has a more diverse range of colors and patterns than natural linoleum, as well as a very affordable price. The service life of this coating may vary, depending on the quality of the material, but generally its operational period is quite long, and is at least 15 years at normal temperature conditions. The disadvantages of artificial fabrics include instability to solvents and sudden temperature changes.
Decorative plaster
This type of finishing is more complex in execution, but despite this, it is becoming increasingly popular, as it perfectly transforms walls and hides small flaws on it. There are quite a lot of varieties of decorative plasters, but they all have high strength and abrasion resistance, and good moisture resistance.
Decorative plaster - stylish decoration interior!
It is simply impossible to talk about all types of this finishing in one section. You can read in detail not only the description of the different types, but also the processes of preparing surfaces and applying finishes to the wall in a separate article on the portal.
Technology for decorating corridor walls “like stone”
In combination with plastered sections of the wall, tiles that imitate natural stone are often used, and more and more apartment owners are interested in this method of decorating hallway walls. Therefore, next we will consider two various technologies stone-like wall decoration. Perhaps the description of these works will inspire someone to independently creative process and will help you save a decent amount.
Indeed, the correctly selected stone texture and color scheme of this facing material can elevate the interior of the premises and give it individuality. However, it should be noted that if the hallway has a very small area, then you should not stick stones on all the walls. It will be enough to cover only the area around the front door with stone, and it is desirable that the material has one of the light color shades.
Below we will consider step by step two available technologies similar decoration of the corridor.
Laying tiles imitating natural stone
First of all, ready facing stone can be purchased at hardware store. In this case, work is carried out in the following order:
| Illustration | |
|---|---|
 | In order for the tiles to adhere securely to the wall, it is necessary to make a row preparatory work, which begin with cleaning the walls of old coatings. It should be remembered that you cannot glue tiles to wallpaper, even if they are securely attached to the wall, since the canvas will not be able to hold heavier finishing material. However, if you plan to lay masonry on individual parts of the wall, you will have to develop a design project in advance, determining the location of the tiles. Then, having taken measurements of the tiles, transfer them to the area of the wall to be tiled, marking the edges of the future finish with a simple pencil. Then you should carefully remove the wallpaper only from these parts of the wall. Thus, it will be possible to combine two finishing materials. If you plan to cover the entire wall with finishing material, the wallpaper must be completely removed. In addition, old, peeling plaster is cleaned from the walls, as well as oil paint, if it was previously applied. |
 | The next step is to prime the cleaned surfaces with a solution containing antiseptic substances. The primer will help protect the walls from mold and other negative manifestations, and will also create high adhesion for the next finishing layers. |
 | If you plan to combine masonry with a painted wall, then its surface must be well puttied. Moreover, this work must be done as efficiently as possible so that there are no stains left on the surface from the spatula and the so-called sinks. It should be noted that this process requires a certain skill, therefore, if there is no experience in such work, then it is better to entrust the leveling of walls to an experienced plasterer. |
 | Putty and dried walls are carefully sanded until smooth using a construction float, on which an abrasive mesh is first installed, and then fine-grained sandpaper. After sanding, the surface is again covered with a layer of primer, applied with a roller with a fluffy nozzle. Primer on water based dries in about two hours. |
 | Next comes the process of painting the wall. Typically, water-based or dispersion paints are used for this purpose, to which the desired color is added. They are also applied with a roller. This type of paint will not interfere with fixing stone tiles over it, but if you want to get even greater confidence in the reliable fixation of the finishing material, then the wall should be marked and the areas where the tiles are planned to be installed should be coated with a primer. |
 | While the paint or primer is drying, you should start selecting tiles. To do this, it is unpacked and laid out along the wall that will be tiled. |
 | Since the “wild stone” tiles have dark inclusions, which are located differently on different specimens, it is necessary to try to arrange the fragments in such a way that the areas painted in more dark color, were evenly distributed in the masonry. It is easier to finish if the entire wall is decorated with masonry, but if it is located in separate sections, usually these are the areas around doorways and corners, then the work should begin with them, from the floor plinth. However, before installing the first row, it would be useful to check the horizontality of the plinth using a building level. |
 | If it turns out that it is not ideal, then you should measure the height of the tiles and mark a line along the top side of the future row using a paint cord. It is along it that the first row of masonry will be laid out. At the same time, in some places underneath the tiles, it may be necessary to make temporary linings from plastic plates or wooden slats. If the plinth has not yet been installed, it is recommended to mark the level, install and secure the support rail or starting profile, on which the first row of tiles will be mounted. |
 | Some tiles made of gypsum may have irregularities on their edges that are formed during their casting - these defects must be cleaned, otherwise they will interfere with the smooth fastening of the elements to the wall. For this purpose it is used sharp knife and coarse-grain sandpaper attached to a piece of timber, or an abrasive stone. |
 | If there is any in the corridor external corner, which will be issued artificial stone, then the work should start with it, and it is best to use special corner elements for this. Before fixing the corner tiles with glue, it is recommended to try them on carefully first. |
 | Next, according to the instructions on the package, the tile adhesive is mixed. Moreover, if the tile is made of gypsum, then adhesive composition should also be chosen on a gypsum basis, and if facing material from cement-sand mortar, then the glue is cement-based. At the same time, to simplify the work, especially when installing tiles on a wall painted in light shades, it is better to choose white tile adhesive. |
 | Some craftsmen prefer to attach the elements of this cladding with “liquid nails” glue, and this can be done under certain conditions. For example, if the tile is gypsum and has a small thickness and weight, and the room in which it will be installed has normal humidity. However, professionals in any case recommend using tile adhesive, since it is cheaper, and such a composition, if it is of high quality, will more reliably fix the tiles to the wall. |
 | During installation work, the tiles will definitely have to be cut. A regular hacksaw can easily cut gypsum tiles, but for cement tiles you will have to use a grinder with a stone disc. |
 | If you plan to make “torn” masonry, and the tile has smooth edges, then it will have to be broken. To get a long protruding element, the tile is first sawed off and then the excess parts are broken out by grabbing them with pliers. |
 | To obtain an arbitrarily uneven edge, it is simply broken off with the same tool. However, it should be noted that these manipulations can only be performed with thin gypsum tiles. |
 | So, the masonry starts from the corner or doorway. The glue is applied to the surface of the wall and the tile itself in a thin layer, since when they adhere, it should only protrude slightly at the edges. Moreover, this excess must be immediately removed with a spatula. |
 | The tile is applied to the wall and pressed well, the glue is removed from its edges, and then it is tapped to the wall with a rubber hammer. Installation of the second and all subsequent rows is carried out according to the principle of brickwork, that is, the vertical joints must be offset by at least ⅓ of the length of the tile. |
 | Each of the laid rows is verified according to construction level, since the tile can become warped by just a few millimeters, which will gradually grow into centimeters, and the work will ultimately be ruined. |
 | Another nuance that often causes inconvenience if ordinary tiles are used to decorate a corner rather than corner elements is the mismatch of their edges, since it is often quite difficult to find perfectly right angles in apartments. |
 | Therefore, before applying the adhesive mixture to the surface, it is necessary to try on two tiles at the corner, and if they do not match, mark and then saw off the protruding excess part. Since this version of the finishing material has a certain volume, masonry made from it will perfectly hide small irregularities in the corner. |
 | Another challenging design area is the arch. But if gypsum material is used for finishing, then this problem can be resolved quite easily, again due to the ease of processing such tiles. |
 | Since the arch can have a different radius of curvature, which is difficult to calculate in advance, the easiest way to cut the tiles is to mark them at the place where they are laid. To do this, the tile is applied to the place where it will later be fixed with glue, and the edge of the arch is outlined on it using a pencil. The cut is made using this mark using a fine-toothed hacksaw. In order not to make a mistake with the place where the element is fixed, it is best to additionally outline it on the wall, lightly pressing the pencil. |
 | Since gypsum tiles are not flexible, it will be difficult to fix them to the arch opening area. The gap that forms between the wall and the tile must be completely filled with adhesive. If “liquid nails” are used for fixation, then the glue is applied to the top and bottom of the tile, and after it dries, only the side gap is filled with it. This way the entire arch is framed. |
 | Next, after the glue has dried, in order to mask the corner joints of the masonry, a paint composition should be sprayed onto it. For this purpose regular will do spray. If this device is not available, you can cover the stones with a liquid paint solution using a soft brush. In any case, it is necessary to ensure that no streaks remain on the surface, so it is recommended to have a sponge on hand to immediately remove them. |
 | The end edges of the stone are carefully painted with a narrow soft brush intended for watercolor work. The work must be carried out carefully, trying not to touch the surface of the wall. |
 | If some of the paint does get on the surface of the wall, it must be removed with a damp sponge, and, if necessary, some areas of the surface must be touched up. |
 | When the paint has completely dried, the masonry is coated with water-based varnish. It does not have an unpleasant odor and dries quickly enough. The varnish is applied with a wide soft brush, since the composition must cover all recessed areas of the masonry. It is best to choose a matte varnish for the coating, since gloss can ruin the entire look, because the “stone” will look unnatural. |
Imitation of masonry using papier-mâché technique
Another option for decorating the walls of the hallway and corridor can be finishing, which will not bring much expense, but will require a lot of patience and effort, as well as creativity. In this case, the cladding is done using the familiar papier-mâché technique. In the example presented to your attention, the master decorated not only the hallway and kitchen, but also his office.
Next, we will consider how to make the material for manufacturing, how to apply it to the walls, and also paint it in the desired shades. Moreover, it should be noted that the shape of stones in imitation masonry can be to suit any taste of the master, and the color scheme is also selected to suit the intended style of the interior.
The shape and color of future “stones” are all the prerogative of the creative master Step-by-step instructions for doing this finishing yourself are in the table below:
| Illustration | Brief description of the operation performed |
|---|---|
 | In order to perform cladding using this technique, you will need ordinary paper egg trays, CMC wallpaper glue, a mosquito net measuring 1000x1000 mm or a mesh bag with small cells, intended, for example, for storing onions. In addition, it is necessary to prepare washing powder for hand washing, as it gives more foam, enamel white and colored paints, soft brushes 150 and 10 mm wide (you will need several of them), electric drill with mixer attachment, plastic basin and bucket. In this case, the production of a paper-glue mixture from ten egg trays will be demonstrated. This amount should be enough to cover an area on the wall measuring approximately 550x550 mm. |
 | It is best to make the working mass in the bathroom, since the work requires a large amount of water. In order not to clog the drain in the bathtub, it is best to protect it with a regular mesh that is installed in the kitchen sink. The trays are handled differently: some craftsmen knead them or cut them into small pieces, others simply immerse them in very hot water. |
 | So, to soak ten trays you will need 6÷7 liters hot water, to which you should add 50 grams of washing powder. The trays are immersed in boiling water one at a time, so that their cells do not overlap, and are left to soak for half an hour. Then, taking a drill with a mixer attachment, use it to mix and knead the resulting mass. |
 | Next, the soaked paper is kept in water for at least two more hours, since the mixture should turn out almost homogeneous, and also without the odors characteristic of tray cardboard. Washing powder will not only remove unpleasant odors, but will also help soften the paper faster and better. After two hours, the mass is crushed and mixed with a mixer installed in an electric drill. Simultaneously with mixing, a kind of “washing” of the resulting mass is carried out. |
 | Next, the resulting “porridge” of paper must be rinsed. To do this, install a cut into a plastic bucket mosquito net. It needs to be laid out well at the bottom of the bucket, and then its edges should be secured to the bucket with ordinary clothespins. Then approximately 1 kg of paper pulp is laid out in the container prepared in this way. |
 | After this, the mesh rises up and twists at the top, then the resulting “bag” is taken out of the bucket and placed on a lattice stand in the bathtub. Next, press on the mesh with the working mass with a mug, squeezing out excess liquid from it. The pressed mass, without freeing it from the mesh, must be rinsed from the powder using running water from the shower. The mass must be turned over and pressed by hand until clean water flows from it. Rinsing is carried out first with cold and then with warm water, after which the mass is wrung out like regular laundry. |
 | The rinsed and wrung out paper is poured into a clean container, as it should be dry and crumble easily. |
 | The same work can be done using mechanical washing machine, in which the centrifuge is installed separately from the washing tank. A mesh bag is installed in the centrifuge, paper soaked in soapy water is placed in it, then the bag is twisted and tied at the top. Then the centrifuge lid is closed, the device is turned on, and the mass is spun. |
 | After spinning, the mixture is rinsed. To do this, water from the shower is poured into the centrifuge, and then the moisture is again squeezed out of the mass. If you have an automatic machine installed in your apartment, then you shouldn’t take the risk, since it has a different spinning principle, and the paper can clog the filters of the device. Therefore, it is best to do the work manually. |
 | The next step is to add one liter of diluted CMC glue to the paper pulp made from ten trays. You will need to add a little more to the mixture when stirring. clean water, and if the mass turns out to be insufficiently plastic, then also about 0.5 liters of glue. |
 | It is most convenient to mix the paper-glue mixture using a mixer attachment installed in an electric drill. |
 | As a result of mixing, you should get a homogeneous, plastic, pleasant to work mixture with high adhesive ability to any surface. |
 | Cladding work begins from the top of the wall from the ceiling. The mass is poured and leveled along the ceiling plinth or the junction of the wall and ceiling. In this area, the mass should adhere tightly to the surface - it is pressed with your fingers, while simultaneously forming the first seam between the “stones”. The advantage of this finishing material is that the paper-adhesive mass, unlike other solutions, does not leave marks on any material located next to the surface being coated. |
 | In this case, an example of the formation of a relief from a mass made of 10 trays is presented. The mass is applied to the wall by sketching or simply applying the collected lump by hand with the necessary force. |
 | Having sketched a small volume of material, it is pressed against the surface of the wall with the palm of your hand. The mixture does not leave dirty marks on your hands and easily adheres to any wall covering - it can be tile, wood, whitewash, concrete, drywall, brickwork and other materials. |
 | After the mass is applied to the wall, it is pressed tightly to the surface with your hands, simultaneously creating approximately the same layer thickness. The facing material does not require ideal leveling, since natural stones almost always have an uneven surface, except for pebbles polished with water. |
 | On the leveled wet layer, the formation of the “masonry” relief begins. To do this, indentations are made by hand in the mass, which will become seams between the simulated “stones.” At the same time, the shape of the “stones” themselves is created. |
 | The master recommends, when creating a relief, alternating small and large “stones”, giving them various shapes. They do not have to be laid correctly, with even seams between them; it is better if the artificial stones created using this technique are arranged randomly. |
 | When forming “masonry” elements, when you press on the mass with your hand, for example, when creating a seam, the mixture on the other side rises, forming a tubercle. It must be pressed while simultaneously distributing it onto the mass located nearby. The mass in the seam between the “stones” must be well pressed against the wall, and in order not to use additional tools, the width of the seam can be determined by the thickness of the finger with which it is formed. |
 | When forming “stones”, it is necessary to ensure that their middle part is not pressed too much inward, that is, their edges should be below the middle. Otherwise, after drying, the “stones” will look like saucers, and this circumstance will certainly reveal their artificial origin, and the masonry itself will not look very aesthetically pleasing. In addition, you should not leave the edges of the stones sharp, which can also ruin appearance relief - they are carefully smoothed, leading to the seam. |
 | You must also always remember that if, when making a three-dimensional pattern on the wall, it includes large and small “stones,” then the paper-glue mass will be used rationally and economically, which will allow you to decorate a larger area of the wall in one batch. |
 | The relief of “stones” can protrude onto different heights from the wall - this will give the masonry more naturalness, that is, there is no need to particularly compare and smooth them. If you plan to decorate the wall with artificial stones that imitate pebbles, then you should add a little more glue to the mixture. It will make the material more flexible and easier to smooth out. |
 | When the work of creating the relief is completed, the wall lined with this technique must be properly dried, otherwise cracks may form on it, or the layer will separate from the surface. To prevent this from happening, drying should be carried out under natural conditions, that is, there should be no draft in the room or heating devices turned on aimed at finishing. If at the end of the work there is excess paper and adhesive mass left, it should be stored in open form, otherwise it will acquire an unpleasant musty smell. If this does happen, the mass will have to be washed again, squeezed out, and then can be used again for work. If moisture has evaporated from the mixture, then before use, add water to it, soak and mix well. |
 | When the created relief on the wall is completely dry, it is necessary to check it for cracks and peeling. If cracks are found, they should be sealed with the same paper-adhesive mixture, and while it dries, you can start marking the colors. In this case, the master first determines the color of each of the “stones” using colored dots. |
 | This method simplifies the work, since first paint of one color is taken and applied to the marked “stones” throughout the facing layer. For painting, it is best to use alkyd matte enamel or oil paint, which is applied to the “stones” in two layers. |
 | Then stones of a different color are painted, and this continues until the entire surface is covered with a layer of paint. The paint is applied to the entire relief of the “stone” up to the seam. |
 | Sometimes, to add naturalness to the painting of one “stone,” several shades are used, which gives the masonry elements a deeper volume. Regarding coloring, we can say that this process can be carried out in different ways, depending on the goal and the style of the interior. It all depends on the artistic taste of the master. |
 | Paint is applied to the seam in such a way that it does not touch the protruding relief of the “stone”. It should not stand out in the foreground, since the task of designing the seams is to give the finish neatness, that is, they should only be a background for the main elements. |
 | In this case, the result of the work is presented in the selected green-brown-beige tones, with seams made in blue shades. However, each master chooses his own color option, which is more suitable for his vision of the created interior. |
 | A properly tiled wall, covered with enamel or oil paint, can be easily cleaned with a soap solution and a stiff brush. Based on this, we can conclude that the finish is moisture resistant and can be used for any of the rooms, including the bathroom. An exception is the area where the bathtub meets the wall - there it is recommended to lay one horizontal row ceramic tiles, harmonizing in color with the future “masonry”. It can also be noted that the mass made from cardboard of egg trays has low heat and sound conductivity, so a wall finished with this material will muffle noise from the outside and will also become warmer, unlike brick or concrete. |
So, available ways and there are quite a lot of necessary materials for finishing the corridor. The main thing is to first decide for yourself what you would like to get as a result of the repairs. The second step is to determine the amount that can be allocated for repair work in a given room, and then look for options that are suitable in all respects.
And in order to spur the imagination of the interested reader, below is a video that presents a lot of very interesting options finishing the corridor and hallway.
Video: a variety of design solutions for decorating the corridor and hallway
The hallway forms the very first and, perhaps, the most important impression of the house as a whole. v
Of course, the very first room that visitors enter is the hallway. Therefore, it is very important that it is formatted properly. The hallway forms the very first and, perhaps, the most important impression of the house as a whole.
Therefore, the renovation of the hallway must be approached competently and with due attention. Of course, many people mistakenly believe that it is easiest to renovate such an inconspicuous room. However, this is not at all true. The fact is that the hallway performs several functions simultaneously. Here you need to place furniture, take care of the surface of the walls and floor. All materials should be very practical, because this is perhaps the most easily soiled area of the home. So, let's take a closer look at how to do it right renovation in the hallway. And so that our words are not unfounded, we will show you illustrative examples decoration of the corridor in the photo.
So, first you need to decide what kind of hallway you want to get. Now the choice finishing materials very diverse. Think carefully about what color and what materials you want to use to decorate the front room of your home. And do not forget that the hallway should convey the meaning and mood of the design of the entire room. For example, it is increasingly used in Lately natural or artificial stone for decorating hallways. It is practical, beautiful, and durable. But there is also a minus - this is a very expensive coating. You can, of course, use wallpaper that imitates stone or brickwork. This option will also look great, the main thing is to choose the right color scheme.
Of course, it is important to take care not only of the walls, but also of the ceiling and floor. For the ceiling modern masters offer many options. This can be regular plastering, or a suspended or suspended ceiling. It all depends on your capabilities and imagination.
When it comes to flooring, traditional laminate is most often used. It washes well and withstands external influences. Tiles are not entirely appropriate for covering the floor in a hallway. Often they make “warm floors” in the hallway, since it is from this room that the cold air. In any case, before starting repairs, carefully measure and correctly calculate the amount of material needed.
It is better to choose either washable wallpaper or paints for the walls. Liquid wallpaper is a know-how that is used to decorate the walls in the hallway. Such materials will allow you to forget about the new for a longer period of time. hallway renovation. After all, all the dust and dirt gets here directly from the street. This is why it is not recommended to use carpeting on the floor.
It is better to level the walls and ceiling before applying the final coating. After leveling, you can begin finishing.
Hallway renovation: lighting
You also need to think about lighting the hallway. After all, this room, most often, is not equipped with windows, which means it does not receive natural light. It is important to understand that different areas require different lamps. After all, when entering a room, you should not experience eye discomfort. You need to take care of the light before you start finishing works. You may have to make additional wiring that will be hidden behind the finishing of the walls and ceiling.
If you have a small hallway, which is very common in our apartments and houses, lighting will also help to visually enlarge the room. A single light bulb hanging from the ceiling will clearly not play the best role in realizing your plans. It might be worth doing multi-level lighting. And in such rooms it is better to place lamps on the walls so that the light does not fall on the ceiling. It’s good if the room’s decoration has enough glossy surfaces. This will only serve to benefit the overall picture.
If the hallway is narrow, place lamps on only one wall. This will visually expand the space. And, of course, add mirrors to the interior. It is better to hang them at the top of the walls. To reduce the feeling of a tunnel in the hallway, place a lamp on the wall in a dark corner. It will be much better this way!
To increase space, it is not necessary to use light colors in the decoration of the room. You can simply use any of the above design techniques. Of course, it is important to take care of the furnishings of the room. You need to place hangers or even a wardrobe, a shoe rack and a mirror in the hallway. Be sure to take advantage of zoning the space of your hallway, even if it is not spacious enough. This can be done both with the help of furniture and through finishing. Just use materials of different texture or color to decorate different areas.
So, as can be seen from all of the above, hallway renovation- not such a simple task. And, if you are afraid of doing something wrong yourself, seek help from specialists. They will give good advice and will make your hallway unique and very cozy!
Date: 07/25/2016
Renovation of the hallway of a small apartment, pictured examples are presented successful arrangement, it’s worth starting with space planning. Due to limited square meters, experts recommend increasing useful footage by using unused niches, adjacent rooms. This will allow the walls of the corridor to be moved apart for the convenience of residents. Is it possible to take this advice as a rule if the bedroom or living room allows you to take away the space or if there are rooms “under economic needs" Due to everyday realities, there are no such possibilities, but you can do otherwise - leave the partitions alone, expanding the space with the help of visual effects.
Bright small hallway
What a small hallway can do
The functional load of the corridor cannot be compared with its area. The hallway is not only an “intermediate room” “from the living room to the kitchen,” but also a place where they undress after coming home from the street, hang jackets or coats, store outerwear and shoes, keys, umbrellas, mail, shoe care products …. And what’s even more important is that they greet and see off guests. Therefore, the room should be not only functional, but aesthetic.
In a small hallway you need to take care of a functional set for outerwear, shoes and small items
Advice:To improve the hallway you need to use all the possibilities, making the most of the space.
So, designers advise choosing cabinets that reach the height of the ceiling, and swing doors replace with an arch or sliding structure. If design advice and custom-made furniture are priorities in arranging a corridor, then renovating the space is the work of the home owners themselves.
For a small hallway, a narrow wardrobe can save space
Attention:For narrow hallways, you can make a small podium at the entrance. This solution will successfully delimit the space.
Hallway design in a small apartment
Narrow hallway with high ceilings
To give such an environment a “down-to-earth” look, you need to use options in the renovation with a multi-level plaster ceiling or paint the surface with a darker paint than the walls. Gloss gives depth, so it is better to give preference to a calm matte paint. Wallpaper with a vertical pattern is contraindicated for rooms with high ceiling heights. It is better to cover the hallway with wallpaper with a horizontal pattern, which will reduce the height and add volume to the corridor. You cannot use the “unity effect” in repairs - when the wallpaper is glued flush to the ceiling without a ceiling plinth.
A multi-level plasterboard ceiling will help make a room with a high and narrow corridor more down-to-earth.
A black suspended ceiling in the hallway will add depth to the room
To slightly visually expand the space of a narrow corridor, horizontal wallpaper with stripes or a horizontal print is often used.
Low ceilings
If you have an apartment with low ceilings, then it is better to paint the surface in cool shades of white. Don’t get carried away with fashionable innovations such as tension or plaster ceiling, since the structure “eats” at least ten centimeters.
The walls will thank you if you choose wallpaper with a vertical pattern, and only in light colors.
Low ceiling in the hallway of a small apartment
- To visually enlarge the space, you can paint or wallpaper the room with light wallpaper - beige, blue, light green, pink.
- The pattern on the wallpaper should not be voluminous! Minor patterns, small flowers or a single-color coating will not stand out and catch the eye.
- You can remove the thresholds so that the floor looks like a single structure without boundaries.
- It is recommended to choose linoleum or tiles for the flooring role. Laminate and parquet should not be exposed to high humidity.
- Wall panels, artificial stone and other design delights are not suitable small corridor, since they hide the space due to the frame.
Decorating the walls and ceiling in light colors will help to visually increase the space of the corridor.
For a small hallway you should choose wallpaper with a small print
Advice:Shades of paint and wallpaper should be matte.
The finishing materials market offers ample opportunities for creative individuals. Innovations and developments do not leave even the most discerning buyer indifferent. But not all “new items” are suitable for a space such as a corridor. And the point here is not only in aesthetic terms - the operational component is much more important. It's no secret that the hallway is subject to the most intense loads. This is where the most dirt accumulates, and the walls quickly lose their former aesthetics. Therefore, you need to choose a coating not only by appearance, but also by its characteristics.
An interesting option for a small hallway would be its design in a loft style; the brick covering is durable and also has a predominantly horizontal pattern.
What should be the wall covering for the corridor:
- Washable;
- Practical;
- Durable;
- "Anti-vandal."
Attention:
The labels always indicate the type of wallpaper.
Glass wallpaper
They are one of the most reliable finishing materials on the market. The wallpaper is textured, impressive, stylish and unusual. They involve subsequent painting in the required color. It is better to choose paint that is washable and resistant to physical impact - latex. The walls can be repeatedly repainted in different colors.
Fiberglass wallpaper is often chosen and then painted in a suitable color.
Fiberglass wallpapers always have an interesting texture that can be played out well
Wall wallpaper
Decorative plaster
You have probably paid attention to the aesthetic and attractive facades of buildings that are plastered in an interesting way, or rather, using the original plaster “fur coat”, “bark beetle”, “lamb”. But such a stylistic solution can also be used to renovate the hallway. The advantages of the finishing material are undeniable: it is not exposed to ultraviolet radiation, has increased resistance to damage, can be repainted and is not washed off with water. If a house plastered in this way does not lose its attractiveness for decades, what can we say about indoors! The only drawback of this coating is the impossibility of frequently changing the color, since the texture pattern may be painted over. This is necessary, because if the plaster can withstand rain and hail for years, then in a dry place any wet cleaning will seem like a joke to it.
Blend for decorative plaster it is better to choose in light shades
Microcement
A budget option for decorative plaster. It is a polymer-cement solution with dyes. Has the advantages of its analogue and can be applied to different types old wall covering (be it tiles or drywall), withstands many cycles wet cleaning, comparable to the strength of stone.
Finishing the corridor walls with microcement is perfect for loft and minimalist style
Flexible stone
Belongs to the category natural materials for finishing walls and building facades. It has all the benefits of minerals and is easy to maintain. It looks original and is rarely found as a material for arranging corridors.
Decorative stone in a small hallway
Fake diamond
Cheaper analogue natural stone. Distinctive feature– it is light weight (compared to eco-minerals). Easily corrects minor wall imperfections. It has a high cost, just like natural stone.
In a small hallway, you shouldn’t decorate the entire space with artificial stone to emphasize the accent; one wall will be enough
Cork wallpaper
Eco-friendly wall covering that does not stand out environment toxins. Suitable for arranging large hallways, as it “eats” a lot of light. Not very scratch resistant, but minor damage is almost invisible.
Minor damage is not visible on the cork wallpaper in the hallway
Quartz wallpaper
A new generation of moisture- and cleaning-resistant wallpaper. The models are a paper or non-woven base on which a layer of sand is applied. Can be in the form of frescoes, painted in desired color. This is one of the most reliable and durable wallpapers that is not afraid of the claws of pets. This coating can be washed with a stiff brush.
Beautiful wallpaper in the hallway
Metallized wallpaper
This type of finishing materials is nothing more than a base + a layer of foil. Wallpaper perfectly reflects light and any electromagnetic radiation. Quite reliable, often have a variety of textures.
Attention:
Paste similar type Wallpaper can only be applied to a completely flat surface.
Metallic wallpaper has a beautiful sheen
Liquid wallpaper
They are a dry cellulose mixture, which is diluted with water and applied to the walls with a spatula. IN further surface can be painted. The advantage is that you do not need to pre-level the walls.
Liquid wallpaper is great for uneven walls hallway
Ceramic tile
All the advantages of ceramic tiles are known to the domestic consumer down to the smallest detail. The disadvantage of using a covering for a corridor is its unaesthetic appearance, which unofficially resembles a bathroom or toilet.
Ceramic tile
What is not suitable for a small hallway
When choosing certain finishing materials, many of which have perfect performance characteristics, it is worth remembering that installing drywall and PVC panels is not the most thoughtful decision, since similar design requires a frame. The frame hides up to 20 cm of usable area.
It is better to choose sliding wardrobes for a small hallway with a mirrored surface of the doors, this will visually increase the space
Vases and pots with indoor flowers inappropriate for the corridor. And the corner hallways must be equipped with appropriate furniture - corner cabinet. Don't forget about lighting! The lighting should be bright. The chandelier can be located in the center of the corridor. The optimal options are spot and directional light with a light intensity controller. Furniture and walls of conflicting colors will leave nothing behind except hostility. Even the most expensive porcelain tiles will turn the corridor into an operating room.
For lighting in a small corridor it is better to use Spotlights, they don't take up much space
Competent renovation of the hallway in the apartment: photo of small-sized corridors
Beautiful doesn't always mean right. This concerns, first of all, the repair of such a problem area as a narrow or small hallway. Often the user is “led” by emotions, preferring stylish wallpaper with a large floral print. In practice - small space the hallway will seem even smaller. In order not to make a mistake with the choice of finishing materials, you need to seek help from designers. They will create an original project for the arrangement and repair of the corridor and suggest what better materials use in finishing.
Design ideas must be combined with the size and space of the room
Modern hallway design
Renovation of the hallway in the apartment 40 photo ideas:
