≡× MENU

• Interior
• Window
• Walls
• Projects
• The buildings

How to glue wallpaper in corners if they are uneven. How to glue vinyl wallpaper: internal and external corners How to glue internal corners with vinyl wallpaper

Very often, in houses with relatively smooth walls, the corners have certain defects, so before gluing wallpaper in the corners, they need to be leveled.

If we neglect this, then facing material it will lie unevenly, which will ruin it appearance not only the walls, but the entire room.

Today, to create beautiful interior, apply Various types rolled finishing material.

They differ from each other not only in color, but also in the material of manufacture.

Every year, non-woven and vinyl wallpapers.

They are considered environmentally friendly, so they are often used in bedrooms and children's rooms.

And thanks to its excellent resistance high humidity And simple care, this material is often used to cover walls in kitchens and hallways.

Preparing the base for wallpapering

Non-woven and vinyl wallpapers, unlike paper ones, are quite expensive, so they do not stick for 1 year.

To ensure that the rolled material lays flat and does not peel off over time, a series of preparatory activities which include the following steps:

• dismantling old finishing;
• plastering;
• puttying.

Before you start gluing external or interior wallpaper in the corners, you need to remove the old finish.

If this is not done, then after some time bubbles and wrinkles will form under the new wallpaper.

And if thin ones are used when gluing paper wallpaper, then the pattern of the previous cladding may appear on them.

Dismantling old wallpaper is carried out in the usual way. kitchen knife or a spatula.

If during the work there are difficulties in peeling them off, then the finishing surface can be treated with heated water and wait 10-20 minutes until the material gets wet.

The next step is to level the walls and corners with plaster.

It is applied in layers.

The thickness of one layer should not exceed 6 mm.

At the same time, the number of such layers depends on the degree of unevenness of the walls.

At the last stage, puttying is carried out, with the help of which the finishing surface will acquire the required smoothness.

For this, 2 types of putty are used: starting and finishing.

The second is distinguished by a more saturated white color and less grain.

After the finishing layer of putty has dried, the walls must be sanded with sanding paper to remove minor defects.

After sanding, the walls are primed again.

In this case, special attention should be paid to the corners, since these places are most exposed to moisture and microbes.

Pasting internal and external corners

Non-woven wallpaper is more manageable than paper wallpaper, so it is easier to work with.

Before gluing wallpaper in the corners, you should understand that one type of glue is used for ordinary roll material, and a completely different one for non-woven wallpaper.

Therefore, the choice of one or another adhesive composition will depend on the type of wallpaper used.

At the same time, with paper wallpaper, glue is applied both to the finishing surface and to the wallpaper itself, and with non-woven and vinyl wallpaper - only on the wall.

Pasting technology external corners slightly different from the interior decoration.

How to cover an inner corner?

To prevent wrinkles from forming in the inner corners of the wallpaper after drying, pasting should be done not with one solid sheet, but with two sheets: one sheet on each side.

To do this correctly, you first need to measure the height of the wall, set aside and cut the required length of the canvas (wall height plus 20-30 mm for allowances).

Then, just before gluing, the wallpaper needs to be bent lengthwise into two parts: one part (the main one) will cover one plane of the corner, and the second (about 40 mm wide) will go onto the adjacent side.

This should be done very carefully so as not to inadvertently damage the non-woven or paper wallpaper.

After this, using a roller or rag, the canvas is smoothed with smooth movements from top to bottom.

In this case, you need to watch carefully so that no air bubbles form under the wallpaper.

At the next stage, the second side of the corner is glued.

This is done with a slight overlap (about 25 mm) onto the previously glued canvas.

Then, according to the mark, using a stationery knife, 2 layers of wallpaper are cut simultaneously, after which the excess parts are removed.

If this procedure is done correctly, then you will definitely like the result of the work.

How to cover an external corner?

If the outer corner is fairly even, then you just need to wrap the fabric and continue finishing.

If you have a crooked protrusion, then wallpapering is done overlapping.

To do this, first glue the canvas to one side of the corner, with a small margin (25 mm), which will extend onto the second plane.

If the folded edge lies with folds, then it can be cut in 3-4 places.

After this, as in the previous case, the stock is cut plumb, as close to the protrusion as possible.

As a result, you will get only a slight overlap, which will be practically invisible.

Wallpapering corners is a rather complicated procedure that requires patience and precision.

However, if you approach the work with all responsibility, taking into account all the rules and wishes, you can be sure that the result will be no worse than if paper or non-woven wallpaper was glued by a specialized team.

Evgeniy Sedov

When your hands grow from the right place, life is more fun :)

Mar 2 2016

Content

Often wallpaper materials are the most common wall decoration. Their popularity has increased due to affordable price and ease of pasting, but not in all places. Anyone can handle smooth surfaces, but when it comes to how to properly glue wallpaper in corners, not everyone can prove themselves to be a professional. In order not to slow down the repair process and make it better, you will have to resort to some construction tricks.

Features of wallpapering in the corners of the room

Pasting a straight wall surface is not difficult, but as soon as you reach a bend, the hassle begins. How to properly glue wallpaper in corners? People already experienced in this matter recommend that beginners observe several conditions:

1. Do not use the whole blade when turning. No matter how smooth it may seem, you still get folds and distortions, because some modern wallpaper materials shrink after drying.
2. Do not start pasting from the very joint of the walls - it is not as smooth as at first glance. It turns out that two panels are spoiled at once. Instead, you need to take a level and draw a vertical line.

There are 2 ways to glue wallpaper in a corner:

1. Place the panels overlapping each other and make a cut in the center of the overlap. Remove cut parts.
2. Glue one panel, bringing the edge 1.5-2 cm beyond the turn, then butt it with the prepared second piece of material.

Preparing the walls

Before gluing begins, you need to make preparatory work:

1. Inspect the wall joints themselves for any irregularities. They need to be leveled using putty, which will dry for a couple of hours. After this, sand the surface with sandpaper to achieve perfect smoothness.
2. Using a chalk level, draw a straight vertical line, moving 4-5 cm away from the joint of the walls. There will be an edge of the canvas.

Step-by-step technique for doing the job

To start pasting, you need to prepare necessary materials– you should have them all at your fingertips. Wallpapering corners requires the following:

• wallpaper of the required length with a margin of a couple of cm;
• glue diluted in warm water that matches the characteristics of your material;
• roller and brush for applying glue;
• a dry cloth to wipe off excess adhesive;
• brush for leveling panels;
• ruler;
• construction knife;
• a stool to reach the top of the canvases.

How to glue internal corners

Here are the stages of work on how to glue paper wallpaper in the corners:

1. Applying glue. Carefully coat the surface of the joint between the walls from top to bottom with the prepared mixture, because there the material comes off easier and more often. Use a roller where needed, and a brush where needed.
2. First part. On the side where the material is already glued, glue the next part so that it falls about 4-5 cm beyond the turn, as shown in the photo. Press the edge with a sponge. Press harder on the turning point to secure it more thoroughly.
3. Second part. Proceed to the other wall. Knowing the width of your material, measure it on the wall so that one edge of the panel overlaps the previously glued one by 2-4 cm. Draw a line, checking it for verticality. After applying glue to the wall, glue the second canvas. Press the edges with a sponge.
4. Trimming excess. Arm yourself with a ruler and construction knife. Using a ruler, make a vertical cut in the center of the overlap. Carefully tear off the top panel from the wall and remove the lower cut part.
5. Final gluing. Carefully lubricate the part that was unscrewed. adhesive composition and re-glue to the wall, smoothing the edge and removing excess glue. The perfect seam is ready!

How to cover external corners

Protruding parts are more noticeable indoors, so they must be done especially carefully. There are two options for hanging wallpaper yourself:

1. The protrusion is perfectly level. Then simply wrap the fabric over the corner joint by 3-4 cm and glue it. Do not cut it, but glue the next one using the usual technology for a straight surface.
2. The walls are uneven. You'll have to use another method.

The second method will not differ from the technology for internal corner joints. Here's how to properly glue wallpaper in protruding corners:

1. Glue the first strip with an overlap of about 4-5 cm at the corner joint.
2. Measure the width of the panel from the protrusion and step back another 5 mm so that when gluing one part overlaps the other a little.
3. Using a ruler, make a cut in the middle of the overlap.
4. The top part will fall off on its own, and remove the bottom by moving the top sheet and gluing it in place.

Such methods are suggested for those materials that are glued joint to joint and do not produce shrinkage deformations. This way the seam will not come apart and there will be no gaps in the wall. For paper materials, these methods are not suitable - an overlap of 0.5 cm is required, so the first method is used, when the overlap is not cut off, but simply checked for verticality using a plumb line. If deviations are found, draw a line and trim what is unnecessary. For a more aesthetic design, a wallpaper corner is often used.

Usage roll materials for surface cladding - this is a popular and sought-after solution that allows you to achieve high-quality results in a short time. But the finishing technology has some nuances. It is especially difficult to glue wallpaper in the corners: the resulting coating must be free of distortions and defects. Most suitable way is selected depending on the situation.

Existing varieties have a certain order of wall cladding, which allows you to achieve the best result.

Vinyl

The technology for working with this option is not very complicated if you perform all the processes correctly.

Step-by-step instruction:

1. The place is being prepared. For convenience, the material is rolled out onto a clean floor or a suitable table with the pattern down.
2. Trimming is carried out taking into account an allowance of 100 mm. If the coating has a complex pattern, then the pattern specified by the manufacturer is used.
3. The canvas is treated with glue and folded in half for better penetration.
4. The composition is applied to the wall, covering areas that extend beyond the width of the roll.
5. The strip is laid on the base and smoothed out well.
6. It is taken into account that standard and meter-long vinyl wallpaper on a non-woven backing can only be glued end-to-end; overlapping will ruin the look.

The vinyl layer on the canvas is quite durable, so the wallpaper can be safely smoothed with a wallpaper spatula without fear of damaging its integrity

On a note! If you have no experience and need to adjust a complex pattern, it is better to prepare: for this, the stripes are placed on horizontal surface, are aligned with each other and the size of the required adjustment is noted.

Paper

Gluing this variety is rarely accompanied by difficulties. For the process, you can use any glue, including homemade glue.

Algorithm of actions:

1. According to the width of the roll, markings are carried out using a level and plumb line.
2. The material blooms into strips, depending on the pattern. For this, a technology similar to working with the vinyl version is used.
3. The canvases are well coated with the prepared composition and rolled up.
4. After surface treatment, pasting is carried out. The excess is trimmed.
5. Most often, paper products are placed overlapping, but strips can also be joined. It is taken into account that after drying the canvas will become narrower, so a special sealant is placed under the seams. paper tape. This rule also applies to other types of wallpaper.

It is impossible to tighten the fabric at the joint by force; the connection is aligned exclusively with the help of a rubber roller

All processes, especially smoothing, are carried out with care, because even multi-layer products are very easily damaged.

Non-woven

To glue this variety, a special version of glue is used, since the material is quite heavy. The preparation of the binder composition is carried out strictly according to the instructions and is applied only to the wall.

Process diagram:

It is important to properly saturate the base: do not leave dry areas. Places beyond the width of the canvas are necessarily affected.

Advice! To speed up the process, it is better to apply the composition with a roller.

Additionally, we suggest watching a video that describes the process of gluing non-woven wallpaper.

How to wallpaper corners correctly

Technology for laying canvases on external and internal corners has differences.

External

These areas are the most noticeable, so they need to be covered with special care. It's easiest if the angle is perfectly straight, but this is quite rare.

If there are defects, the process becomes more complicated. If the corner is blocked, then you will need to trim the canvas along the bend line in order to overlap one section with the adjacent one. This method is not suitable for varieties with complex patterns.

There is another way:

1. The strip is glued to a section of the wall.
2. Using a special spatula, the material is carefully smoothed out to fit the existing bend, and a transition is formed.
3. If required, part of the laid canvas is torn off, after which the excess is driven up or down. There should be a margin on both sides.
4. To adjust the pattern in case of skew, the next strip is overlapped until the pattern is aligned with a distance of 5–10 centimeters from the edge.
5. Using a ruler, which serves as a stop, the applied canvases are cut exactly according to the drawing.
6. If required, the joining areas are additionally coated with the compound.

Joining an external corner with a trim on one of the adjacent planes is considered the most effective way arrangement

This method does not completely correct the misalignment, but makes further gluing and adjustment easier.

Interior

The technology for working with such a section is almost identical to the previous process, but has some nuances:

1. All sides are well treated with wallpaper glue. If the composition is applied to canvases, the impregnation must also be quite thorough.
2. Laying begins with the wall from which movement is carried out. The first fragment is aligned with the previous one, carefully smoothing it into the corner. To do this, the waves are driven to one side with a rubber spatula.
3. The part that falls on the adjacent wall is slightly pressed.
4. Further actions depend on the situation. Most often, you need to trim the existing folds in the middle and overlap the excess.
5. To achieve better combination, the edges are shortened and coated, after which the segment is located on the main part of the canvas.

Technically, joining an internal corner is not much different from similar work on external structures, but this process is considered simpler, since internal corners are visually less noticeable

This technology makes it possible to glue different types products, but if the corner does not require trimming, installation is carried out in a standard manner. To do this, the joint of both sides is made with a margin in order to level out the unevenness by adjusting and cutting at the point of alignment. This will take longer, but will get rid of the overlap in the corner.

Video tutorial: how to glue wallpaper with corners trimmed

Joining wallpaper with a pattern

Work technology:

1. The strip is laid on the initial part of the wall and is gradually distributed over the surface. The waves are driven towards the corner.
2. The material is carefully fixed onto the inner fragment and smoothed from top to bottom. It is taken into account that the canvas must be cut with a significant margin, since trimming the lower and opposite edges will be required.
3. The part that falls on the perpendicular wall is distributed. The areas near the baseboards are adjusted.
4. If the side is uneven, then it needs to be pasted over with the next strip lying completely in vertical plane. The offset must affect the pattern being combined.
5. A ruler is placed exactly along the line, and the excess is cut off using a stationery knife.
6. The second strip moves towards the corner strip; the gap needs to be additionally glued.

If there are no problems, you can join directly along the inner corner, but this will require a certain level of skill.

Wallpaper with a pattern is joined according to the same principles as without a pattern, but if you stick a horizontal mark from the adjacent canvases in advance masking tape, then it will be easier to combine the ornament

What to do if the joints are crooked

Perfect straight corners are rarely found in rooms, so to eliminate various problems, you can use the recommendation that many designers use - combination. It is necessary to cover the transition from wall to wall with wallpaper with a pattern or bright colors. Part of the pattern should extend to the adjacent side, where it is trimmed at a right angle and combined with a plain material. The joining line will be smooth, and any existing imperfections will not be noticeable.

The technology of wallpapering corners is complicated only at first glance. Wallpapering walls will help create a cozy homely atmosphere in the kitchen. Thanks to modern developments this finishing material, and in particular non-woven wallpaper, can compete with plastic in strength and durability. At the same time, they are more environmentally friendly, allow air to circulate and are easier to work with. The only thing you will have to tinker with is to figure out how to glue the wallpaper in the corners.

Choosing suitable wallpaper for the kitchen

Correctly selected wallpaper is already half the success. By saving on quality, you can greatly lose in durability, and in a year or two you will have to do repairs again.

Non-woven wallpaper is one of the best options for kitchen

Non-woven bases are more convenient when it becomes necessary to change the wallpaper. To do this, you just need to remove the vinyl layer, and the new canvas can be glued to the old finish.

Let's look at what types of wallpaper there are, and whether they can be used to cover the kitchen:

• Paper wallpaper- not a suitable option for the kitchen. Under conditions of temperature changes, high humidity or dryness, the paper deteriorates and the design fades. Having decorated the kitchen with paper wallpaper, in such a microclimate one cannot count on its long service life.
• Paper backed vinyl– more durable material. They can be washed and glued for painting. Such wallpapers do not fade in the sun and are resistant to moisture. The gluing technology is the same as for paper ones. But since vinyl makes the canvas heavier, glue is chosen for heavy wallpaper. You should also keep in mind that not all vinyl flooring is breathable.
• Vinyl on non-woven base– are highly durable thanks to non-woven fabric as a lining. There is no need to be afraid that they will tear or shrink. This type of wallpaper is glued end to end. Due to the fact that the glue is applied only to the wall, energy and time are saved during the repair process.
• Non-woven wallpaper– thanks to their dense structure, they perfectly mask unevenness and cracks. They allow air to pass through well, without turning the kitchen into a “greenhouse”. Perfectly suitable as a base for painting. During the gluing process they do not stretch or tear. Easy to care for, they can be washed and vacuumed.

Required materials and tools

To properly hang wallpaper and not be caught off guard by the lack of necessary tools, before repairing, check that you have everything you need.

You will need:

• wallpaper,
• glue,
• assembly knife,
• scissors,
• putty knife,
• plaster,
• building level,
• plumb line,
• sponge,
• rubber roller,
• ruler,
• pencil,
• brush.

Pencil – essential auxiliary tool for wallpapering corners

Subtleties of wallpapering corners

Wallpapering is a simple matter, but it also has its own subtleties. As a rule, difficulties arise if you do not know how to glue wallpaper in the corners. When at least one corner turns out to be crooked, as it is glued along the wall, an increasing distortion of the canvas will be observed relative to the surface of the floor and kitchen windows or ceiling.

You should not rely on the doorway as the starting point for wallpapering the walls. Check with a plumb line that it is truly perpendicular to the floor. There is a high probability that the frames are also installed with an error, which will lead to misalignment and the corner will be swollen.

The tradition is to start decorating walls with wallpaper from door and window openings originates from the need to glue overlapping paper wallpaper so that the latter is less noticeable. With the advent of vinyl and non-woven materials, such a need has disappeared, since the fabric is glued end-to-end.

Smooth corners are much easier to paste than curved corners.

For large irregularities, some tricks will help

Before starting to work with wallpaper, it would be correct to level each corner with plaster using a building level. Minor unevenness can be dealt with by slightly overlapping or cutting off an extra piece of fabric.

Trimming wallpaper in corners (video)

Wallpapering interior corners

A corner properly wallpapered does not wrinkle, the edges of the canvases do not diverge, forming a gap. To achieve such an accurate repair, they resort to some tricks.

For this:

1. A layer of glue is applied to the wall. If the wallpaper is non-woven, you do not need to apply glue to the back side.
2. The edge of the canvas is placed on the adjacent wall with an allowance of 1-2 cm.
3. The wallpaper is pressed tightly against the wall using a sponge. If the canvas wrinkles, make cuts with scissors towards the swellings and straighten the material.
4. After this, they begin to cut the canvas, which will lie in the corner from above. Using a ruler and pencil on the reverse side, put it in mirror image that overlap that went onto the adjacent wall, and cut off this excess.
5. The cut fabric is glued so that the cut edge ends up exactly in the corner.

Detailed instructions for wallpapering internal corners

Wallpapering external corners

Often the kitchen design is designed in such a way that doorways It is necessary to paste over the protruding outer corner as well.

Wallpapering corners - not an easy task with large curvature of walls

For this:

1. Take measurements from the top and bottom starting points for the wallpaper to the corner plus 3 cm to wrap it.
2. Cut the wallpaper to the required dimensions.
3. Apply glue to the walls with a brush.
4. The edges are pressed tightly against the wall, making cuts where wrinkles form.
5. If the pasting is done with non-woven material, upper layer It is cut along the corner and a narrow strip is carefully removed.
6. A new sheet on the adjacent wall on the other side of the corner is glued over the non-woven edge.
7. Go over the joints with a rubber roller.

That's all the tricks on how to glue wallpaper in corners. Knowing these subtleties, there should be no difficulties with kitchen design. Such simple solutions will help create cozy interior kitchens.

How to glue wallpaper in corners (video)

Wallpapering walls - affordable modern remedy interior decoration. Depending on the material used, you can hide some flaws and defects in the walls. People involved in renovation know that incorrect wallpaper application technology and haste lead to ugly consequences and a waste of time and effort.

Before you get started, read the instructions for applying wallpaper to walls.

What angle should you start from?

Properly hung wallpaper will look perfect in the interior of your home. To work you will need:

• wallpaper;
• wallpaper glue;
• ruler;
• roulette;
• dishes for diluting glue;
• pencil;
• roller and brush ( different sizes);
• soft dry cloth or wallpaper brush (to remove air bubbles);
• sharp stationery knife;
• stepladder or chair.

Many people recommend starting work from the door, while others recommend starting from the window. In fact, it's the other way around. Previously, canvases were produced with a special edge for overlap. Therefore, we had to start gluing from the far wall with the window. Nowadays they produce different types of wallpaper, which are preferably glued end-to-end.

Under no circumstances should you start gluing the material from the corner. Be sure to level the walls and prime them. Wallpapering uneven walls is not only difficult, but in some cases impossible.

For those who prefer to overlap, the first roll should be glued from the window. If you are not confident in your abilities, it is better to start from the doorway.

The main thing is to glue the first roll and then build on it.

Rules for gluing

The industry produces various types and types of wallpaper. There are paintable wallpapers - non-woven wallpaper. The advantage is that they can be painted in any color. Economical way interior decoration, because the costs are only for paint.

The wallpapering technique requires sequential steps:

• wall preparation;
• temporary removal of skirting boards (if possible);
• diluting the glue according to the instructions on the package;
• lubrication of the canvas (sometimes lubrication of the wall is required);
• applying the roll to the wall from top to bottom;
• removing air bubbles and wrinkles.

Rules for gluing simple wallpaper(53 cm wide) differs from meter ones (1 meter wide). At first glance, it seems that meter-long materials are much more difficult to glue.

It turns out that this is quite simple if you understand how to hang regular wallpaper.

There are a number of benefits that will change your mind:

• less effort and time;
• cheaper standard wallpaper;
• creating a seamless effect;
• high quality(made in Belgium, Italy, France);
• creating an interior for every taste.

Before purchasing wallpaper, be sure to calculate the cost. For this, a formula from geometry is used: (wall + adjacent wall) x 2. And remember that the length of one canvas on the wall is taken with a margin of 5 cm. Always take a spare roll so that there are no shortcomings when you paste door jambs and protrusions. Be sure to check the length of the canvas itself on the roll in the instructions.

Required condition According to safety precautions, it is necessary to de-energize the apartment or house. After disconnecting, remove the top panels of sockets and switches. Starting gluing, it is necessary to clean the room from dirt and dust.

Remove old wallpaper coverings using ordinary warm water. Wet the coating with water using a spray bottle and wait 20 minutes, after which the wallpaper will easily come off the walls. Remove paper using a knife or spatula. Vinyl sheets are easier to tear off using perforation.

It's much more difficult to get rid of paint. For this they use grinding machine or drill with special nozzle, but it is better to use chemical solutions for removing paint and varnish.

Using the wet method of removing old coatings, less dust is generated and the plaster does not peel off. After removing the old coating, it is necessary to eliminate and repair weak points (cracks, potholes, bulges).

Be sure to level the walls and prime them. Wallpapering on uneven surfaces is not only difficult, but in some cases it is impossible to do. A particular difficulty for beginners in this business is the issue of gluing external and internal corners.

Internal corner

Action technology:

1. Applying glue to the canvas or, if necessary, to the wall. Be sure to lubricate the wall joint thoroughly, as this is the most labor-intensive part in the corner.
2. The canvas is glued so that it overlaps the adjacent wall by 4-5 cm.
3. Knowing the width of the material, stick the next wallpaper (2-4 cm) on top of the previous one.
4. Trim the protruding parts and glue the top material in place.

If there are sockets or switches in the corner, you need to cut out round hole (smaller sizes switches) made of canvas in this place.

Availability rounded corners promotes the formation of air voids. Be sure to make an incision in this area and glue the material tightly. Apply to this area large quantity glue.

External corner

The outer corner is especially noticeable in the apartment, so it requires strict accuracy.

There are 2 types of gluing external corners depending on the unevenness of the corner:

1. If the angle is even, the canvas is glued so that it protrudes 3-4 cm on the adjacent side. Next is the gluing process using standard technology.
2. Not smooth walls. In this situation, the protrusion of the canvas onto the adjacent wall increases (4-5 cm).

It is necessary to measure the width of the panel and retreat another 5 mm. This way the gluing will overlap.

A cut is made in the middle of the overlap. Pushing aside top part wallpaper, remove protruding parts of the canvas. After removal, glue the top sheet in place.

Cuts are made on the convex surfaces of the wall and the material is pressed tightly against the wall. These methods are intended for overlapping gluing (for wide wallpaper). The designs of these wallpapers are designed to hide imperfections and protrusions.

These options are not suitable for standard paper webs. In this case, the first option with butt gluing is used.

If the walls are uneven

Perfectly straight walls are a rarity. Small errors in the unevenness of the walls are acceptable, but with large deviations and noticeable curved surfaces it is impossible to hide this when wallpapering. On the contrary, the appearance of the room’s interior is distorted.

In that case, if there are cracks, they must be repaired cement mortar . For minor cracks use gypsum plaster. Also, it will not be possible to paste wallpaper beautifully and efficiently. The appearance will not match the expected results. In such cases, preparatory work must be carried out. Putty will be your assistant in this.

Application rules:

• clean the surface from dirt and dust;
• tear off the old coating (if any);
• apply antibacterial impregnation;
• prime the wall;
• apply 1 layer starting putty;
• apply a painting mesh over the putty (to prevent cracks from appearing);
• apply a second layer of putty;
• apply two layers finishing putty(thickness 2-4 mm);
• after complete drying, wash with a primer;
• remove all roughness and uneven surfaces using sandpaper.

How to stick models with a pattern?

Wallpapering corners is a difficult job in itself, especially for a beginner.

Plain colored wallpaper is a great way out. But you can bring liveliness to the interior only with the help of drawing. Also, in some cases, such models can cover up irregularities. Do not forget that the canvas is glued overlapping, otherwise the pattern will add an awkward look to the interior, and all the imperfections will be visible.

You can use the method of selecting a pattern, not forgetting that the canvases are glued overlapping, and they need to be cut off. The drawing should be of medium size and strictly plumb. Large or too small drawings add a distorted effect.

A selection different colors Canvases can be used to divide a room into zones without resorting to additional costs (arches, partitions). It is important that the colors are in harmony with each other.

Uneven walls and corners are found not only in old house buildings, but also in modern new buildings. It is precisely because of this deficiency that problems arise with interior decoration. To avoid sad consequences, you should follow the rules:

• In order for the wallpaper to stick better on the outer corners, it is necessary to press it as tightly as possible to the wall. Glue the wallpaper from top to bottom, gradually lowering towards the floor, thereby avoiding the appearance of folds.
• If glue gets on front part material, remove it immediately with a soft cloth. The front sides of some types of canvas become unusable from wallpaper glue.
• If an air bubble is detected, it must be punctured. Use a syringe to inject glue and smooth it out.
• The inner corners of the room are the most problematic; it is in these places that peeling, swelling, and tearing occur. For effective and reliable corner gluing, add PVA glue (10%) to the water when preparing the glue. Mix the glue until smooth so that there are no lumps.

• Make sure there are no drafts. They prevent complete and uniform drying, after which the material peels off. It is allowed to ventilate the room only after the wallpaper has completely dried. This happens within 2-3 days.
• To better cover areas with windows and wooden openings, the canvas must be taken with a reserve and allowed to dry completely. Only after this, carefully cut off the excess material with a stationery knife.
• The unevenness of the wall is not always noticeable. Only when pasting the internal and external corners will flaws and incorrect alignment be visible. To avoid these shortcomings, immediately before work, be sure to check the curvature of the walls using a building level and plumb line.
• In the presence of thermal heating, use a thin narrow brush to lubricate the glue.