home > Foundation > Review of roll insulation. Roll insulation: types and features of roll insulation. Cork insulation for surfaces

Review of roll insulation. Roll insulation: types and features of roll insulation. Cork insulation for surfaces

Insulating boards do not show adequate effectiveness when insulating large areas, as well as pipes and ventilation ducts. This is due not only to their technical parameters, but also to their high density and rigidity, which excludes the possibility of high-quality coating of elements with complex geometry. In such a situation, it is more advisable to use roll insulation, the varieties and features of which will be discussed in this material.

Materials of this group are most widespread in the domestic market. This is due not only to their excellent operational and technical data, but also to an acceptable pricing policy - such a combination is so far unattainable for competitive offers.

Flexibility makes work easier

Assortment and features of species

The term “mineral wool” is a unified designation for a whole range of heat insulators, namely:

basalt wool - for the production of this material, the technology of melting certain rocks is used, followed by the formation of the finest fibers on their basis, woven into a single carpet;
glass wool is a material, although it is considered obsolete, but still has a fairly high demand due to its affordable cost. For its production, remelted broken glass is used;
slag wool - it is based on waste obtained in the metallurgical industry. Due to this, such insulation in rolls has a lower cost than basalt and glass wool.

Material Specifications

Each type of mineral wool has its own distinctive features and characteristics. Thus, glass wool perfectly resists high temperatures, up to 450 degrees - after exceeding this parameter, the material is destroyed irreversibly. The highest density is 130 kg/m3, thermal conductivity values vary in the range of 0.038–0.046 W/m*C.

Glass wool is not flammable, it does not even smolder, it perfectly absorbs vibrations, resists sound vibrations and does not shrink even after long-term use. At the same time, the material is not moisture resistant, and getting it wet completely eliminates the entire range of positive characteristics. It is worth noting the fragility of glass wool, as well as the fact that contact with human skin causes severe itching.

As for basalt wool, such rolled thermal insulation can withstand temperatures up to 700 degrees. Its thermal conductivity is 0.035–0.045 W/m*C, and its density reaches 220 kg/m3. The material is resistant to moisture; slight wetting does not affect its parameters at all. Basalt wool is an environmentally friendly and non-irritating material.

Slag wool has the largest mass, and its density reaches 400 kg/m3. The material is characterized by minimal thermal conductivity - 0.046–0.048 W/m*C, and the highest temperature it can withstand is 300 degrees - its increase causes melting of the slag wool and destruction of its structure.

The dimensions of the materials largely depend on the manufacturer, but most often they have the following standard sizes:

length – varies between 3-6 m or more;
width - standard 0.6 and 1.2 m, although individual products brands can have a width of 1.22 m and 0.61 m;
thickness – 50, 100 and 150 mm.

Foil insulator and its properties

It is worth noting that manufacturers often cover the heat insulator on one side with a layer of foil, which makes it possible to protect the coating from the negative effects of ultraviolet rays and moisture penetration. Its use is advisable when insulating a room from the inside, and the base can be made of a variety of materials.

Optimal solution for internal thermal protection

Types of insulation and features of each type

The backing is made from foamed polyethylene, cork or expanded polystyrene. Expanded polystyrene is an affordable and very practical rolled foil insulation that does an excellent job of sound absorption, is not hygroscopic and can dampen even minor vibration manifestations.

The Thermo-Tap heat insulator has excellent reviews among consumers, the roll length of which reaches 10 m with a width of 0.5 m. Practice shows that such insulation perfectly resists fungus and moisture, but at the same time has lower thermal insulation values, inferior in this aspect products made of foamed polyethylene.

It is impossible not to mention the cork base for the heat insulator. The material is characterized by high strength, light weight, excellent aesthetic properties and absolute harmlessness to humans. For rooms with high levels of humidity, it is recommended to use a wax-impregnated cork backing. The length of the roll does not exceed 10 m, its width is 0.5 m.

Cork underlay is used for flooring

Foam-based polyethylene is a fabric consisting of tiny cells filled with air, covered with a layer of paper on top, which is attached by lamination. Thanks to this, it is possible to achieve the most durable and reliable connection with any type of base.

Thermal insulator with frost protection

The most common type of foam insulation is Polifom, produced in rolls with the following dimensions: length - 14 m, width - 0.5 m, thickness 5 mm. Its density is 30 kg/m3, it perfectly absorbs sounds up to 22 dB, while offering a minimum thermal conductivity of 0.039 W/mK.

External coating and its relevance

The outer covering can be foil or have a metallized coating. Each option has its own characteristics, and its use may be justified in a given situation. Thus, metallized material retains steam well, but does not have the highest heat reflection rates.

It is indispensable when carrying out insulation work in bathrooms and shower rooms, as well as other rooms with high humidity levels. It is worth noting that such spraying does not have high strength - even a slight mechanical impact is enough to damage its integrity.

Rolled insulation with foil has excellent heat-reflecting data and is resistant to various kinds external influences. It can be placed behind radiators without any problems in order to retain more heat inside the room.

Easy installation

As for the disadvantages, foil insulation has poor vapor permeability, does not withstand direct contact with concrete, and the cost of a product with a thick layer of foil will be quite impressive.

The main advantages of foil insulation

Among the main advantages of foil heat insulators, the following are particularly worth noting:

excellent thermal shielding performance, about 97%;
good functionality and the possibility of using not only walls, ceilings and floors, but also all kinds of industrial units for insulation;
minimal roll weight and ease of installation without the need to arrange frames and other structures. Fastening is possible using construction adhesive or regular polyurethane foam;
reasonable cost;
environmental friendliness and safety.

Inter-crown heat insulator and its features

There are also inter-crown roll insulation, which is a rather specific solution designed to fill voids in the inter-crown space. The crown is a level in a house made of timber or logs. No matter how well the installation is carried out, including using profiled timber, there remains free space between the crowns, which is precisely filled with this type of insulation.

It is produced exclusively in narrow rolls, and it is always made from natural and harmless materials, including:

batting;
jute;
flax and others.

Laying of material is carried out not only during construction work, but also after several years after their completion - as the wood is used, it dries out, which necessitates additional caulking (driving insulation into existing cracks using a wide chisel and mallet).

Manufacturers of thermal insulators and their products

Roll insulation from several manufacturers is in greatest demand among consumers.

Knauf is a German brand whose products do not contain formaldehyde, which gives finished product absolute safety and harmlessness, relevant during installation work.

Such insulation materials do not harbor rodents and insects, they have a wide product range, a long service life and can be used for insulation not only of apartments, but also of country houses (cottages).

Isover is a French manufacturer offering wide choose roll insulation with excellent performance characteristics, including those with foil coating. The product is suitable for carrying out insulation measures both indoors and outdoors; it is not subject to combustion and can be extinguished in a fire.

Insulation for external and interior work

URSA - Spanish insulation materials under this brand are characterized by a long period of operation with full preservation of the main technical parameters. The manufacturer guarantees the highest quality of its products and their effectiveness in both private and industrial construction.

"TechnoNIKOL" - Russian manufacturer offering products High Quality at very affordable and reasonable prices. These roll insulation materials are produced on the latest equipment using innovative technologies and techniques, which makes it possible to guarantee not only quality, but also a long service life.

When going shopping, it is worth remembering the following aspects of your choice:

Various variations of insulation are suitable for indoor and outdoor use.
The surface that will be covered with roll insulation also matters. Eat fundamental difference between the materials used to insulate the ceiling and walls. Each of these bases has its own insulation.
It is also important to remember what material the walls are made of. Thermal insulator for wooden base may not be suitable on a concrete base and vice versa.
When choosing the thickness of the material, it is worth taking into account the temperature conditions in winter and the climate characteristics for a particular region.
Before purchasing, you should definitely familiarize yourself with the quality certificates and other permitting documentation for the selected roll insulation, and in addition, make sure that the packaging is intact. Moisture, even in small quantities, can negatively affect the calculated parameters of the material and its properties.

Choose quality material trusted manufacturers

Insulation in rolls is available on the market in a wide range. Each of them has its own characteristics, positive and negative characteristics. The choice of a specific option is up to the user, but if there are difficulties, you should not rely on chance. It is better to seek help from professionals and save your nerves and money.

Wall insulation with roll insulation is most often used in cases where the wall area is significant and there are long straight spans. In this case, it is possible to achieve significant savings in material costs and performance compared to insulation in the form of slabs or mats. A variety of insulating materials are supplied in rolls, from mineral wool to pressed cork. Each of them has its own advantages in specific conditions. Installation of roll insulation is not complex operation and does not require highly qualified workers or expensive equipment.

Main types

Experts highlight following features and types of insulation supplied in rolls.

Based on material, insulation materials are divided into several types:

Mineral (glass or slag wool). Typically used for external walls.
Polymer – based on foamed plastics. Used to insulate walls from the inside and outside.
Cork - from the pressed bark of the cork tree. Rolled cork insulation for interior walls is attached under the wallpaper.

Mineral and polymer roll insulation can be covered on one side with aluminum foil to reduce thermal conductivity and improve waterproofing. A thin layer of foil reflects over 95% of thermal radiation, returning heat to the insulated room. Foil not only reflects heat well, but also increases the strength of the material.

Mineral basalt wool in roll

Characteristics

Rolled insulation materials are characterized by the following main parameters:

Environmental friendliness. All models on the market must comply with safety requirements for installation, operation and disposal. They must contain small amounts of harmful substances; these substances must not be released from the insulation during its storage, installation and during use. The packaging indicates the disposal method. The materials are resistant to organic solvents and other active substances.
Fire and bioprotection. Mineral insulation does not burn on its own and prevents the spread of flame. Foam materials can withstand fire for a certain time. The materials prevent the formation of mold and repel rodents.

Air and vapor permeability. Key characteristics. They show how much air or water vapor at a certain temperature can leak through a unit area of material. Vapor permeability is necessary in order to remove excess moisture from the room to the outside through the walls and their ventilation systems.
Strength. Important characteristic insulation under wallpaper. Touching, including with hard objects, should not damage the wallpaper.

Advantages and disadvantages

The main advantages of rolled material are:

Versatility. Suitable for thermal insulation of any surfaces. For complex spatial shapes, including curved ones, you can cut out a suitable piece.
Minimum requirements for surface preparation before installation.
Benefits in terms of material price and work productivity when insulating large areas of walls, especially straight sections.

Possess rolled materials and shortcomings.

High labor intensity when laying in frequent lathing; additional time is required for cutting.
Low rigidity does not allow them to be used where it is necessary to withstand significant loads.

In general, the advantages compensate for the disadvantages, which explains the high popularity of roll materials among consumers.

The materials are harmless to health provided they are correct operation and compliance with fire safety regulations.

Popular brands

The domestic market has no shortage of rolled materials. Different manufacturers are leaders in different types.

Knauf

The German company produces excellent mineral insulation materials. They are free from formaldehyde and other harmful substances, and thanks to the specially designed fiber structure, they do not provoke allergic reactions. However, the manufacturer recommends carrying out installation work with thick gloves. They perfectly muffle noise and are impregnated from insects, rodents and mold.

Mineral wool Knauf 1220Х6148Х50

Dimensions 1220Х6148Х50 MM (15 m2).
Thermal conductivity: 0.037 W/(m°K).
Density 12 kg/m3.
Cost 1100-1200 rubles.

Izover

The French company launched production at local sites. Offers a wide range of rolls with thicknesses from 20 to 150 mm, allowing you to retain heat in all weather conditions. There are many foil models that can be used in rooms and buildings with high humidity.

Isover Klassik 50 mm thick

Size 50*1220*5490mm.
Packaging 13.4m2, 0.67m3, 2 mats.
Thermal conductivity 0.04 W/(m*K).
Density 10.5 kg/m3.
Price from 750 rub.

Ursa

Easy to install, the material has a long service life and excellent fire protection properties.

For wall insulation, the Ursa Geo M11 model is offered.

Ursa Geo M11 for wall insulation

Size 7000x1200x100 mm.
Average density – 11 kg/m³.
Flammability group NG.
Thermal conductivity – 0.040 W/(m°K).

Topizol

Foamed roll material is available in thicknesses from 3 to 20 millimeters. Performs well in high humidity conditions. Not subject to rotting. Very light, easy to install. Foil models resist strong gusts of wind (provided they are installed correctly). Characterized by excellent vapor permeability.

Foamed polyethylene

size 8 mm (18 m 2) wide. 1.2m;
weight 8 kg;
price 850 – 1100 rub.

Is good choice insulation of walls, including loggias, attics, attics. It has low density, which makes transportation and handling easy and convenient.

The manufacturer claims a service life of 30 years.

Penofol

The heat-insulating layer is made of foamed polyethylene. Several types of penofol are available:

A – foil on one side.
B – foiled on both sides.
C – on one side there is foil, on the other there is a layer of adhesive applied to facilitate installation.

Available in thicknesses from 2 to 40 millimeters, foil thickness is 30 microns. It does not emit any harmful substances and is recommended for insulating children's rooms.

B. Double-sided filming

Foamed polyethylene Penofol V-10 15000x1200x10 mm.
Vapor permeability: 0.001 mg/(m h Pa).
Density: 35 kg/m3
Thermal conductivity: 0.049 W/(m*K).
Cost 1400-1600 rubles.

What to consider when working

Insulation with mineral roll materials can be carried out at any time of the year, it is only important to ensure that the material is protected from precipitation.

The use of foam materials mounted on an adhesive layer depends on the air temperature. Usually the limit is down to –10C. Special adhesives are also produced that are effective down to –20C.

Before insulation begins, minimal surface preparation is required:

Dismantle pipes, electrical wiring, lamps, decorations, plants, etc.
Clean the walls from remnants of old coatings, debris and dust.
Install sheathing for mineral insulation.
Level and clean the surface for gluing foam thermal insulators.

Installation does not require special equipment; the tools you will need are:

construction knife;
stapler;
screwdriver;
hammer;
double sided tape.

It is more convenient to carry out installation and cutting of roll insulation together by two people, especially for large volumes of work. Small volumes can be done by one master.

Insulation process

The sequence of operations when installing mineral insulation is as follows:

A vapor barrier film is attached to the prepared wall.
The sheathing is made of wooden bars or metal profiles. The recommended guide pitch is 50 or 60 cm.
Rolls are cut in accordance with the selected pitch. The cutting must be carried out so that the insulation fits tightly between the guides and, when straightened, provides a better fit to the guide.

Disc dowel

How do you look at the prospect of reducing home heating costs by almost a third? We think this is a case where comments are unnecessary. It is possible to achieve such a result; you just need to choose the right thermal insulation for the roof.

One of the most common thermal insulation materials mineral wool is considered, in particular in the form of mats. However, when it is necessary to insulate, for example, large areas, such a solution is ineffective. For such cases, roll insulation is more suitable.

All materials of this type have approximately the same advantages, which explains their high demand. We are talking about their qualities such as

low thermal conductivity,
good sound insulation,
optimal hygroscopicity,
high hydro-repellent properties,
chemical resistance,
fire safety.

And this is not the whole list.

Rolled insulation, due to its elasticity and flexibility, easily restores its shape and is suitable for work on uneven surfaces. It has no temperature restrictions, as it retains its performance characteristics at extreme temperatures.

Scope of application of insulation in rolls

It is successfully used for roofs and basements, floors and ceilings, pipes and more. Installing thermal insulation from this material is a fairly simple process. Moreover, the work can be done independently, without the involvement of additional labor. Therefore, this type of thermal insulation has gained great popularity in private construction, in particular, bathhouses, outbuildings, etc.

Types of insulation

A separate group includes materials that have protective layer from foil. They are somewhat more expensive than others, but have many additional valuable properties.

Foil itself does not have the thermal conductivity necessary for insulation, however, it effectively retains heat due to the ability of the reflective surface to block infrared rays from the room. It is worth noting that at the same time it does not allow their penetration from the outside. The latter is a rather useful quality for roofing insulation, especially in hot summers, when the roof gets very hot under the influence of sunlight.

Roll foil insulation allows you to ensure the maximum length of the material, that is, it is laid from one whole strip, which is extremely important for its efficiency. . These include foam rubber, polyethylene and other materials in roll form

These materials do not hold their shape and are easily rolled up. They are quite effective and easy to work with. Unlike foil thermal insulation, they are used in combination with a vapor barrier, which creates an ideal tandem against the cold.

These include foam rubber, polyethylene and other materials in roll form. These materials do not hold their shape and are easily rolled up. They are quite effective and easy to work with. Unlike foil thermal insulation, they are used in combination with a vapor barrier, which creates an ideal tandem against the cold.

This is the most common type of insulation. This form of packaging is considered by many to be optimal, since with this approach long strips of insulator occupy a small volume. Most often, floor beams or mounting profiles are installed in increments equal to the width of the roll. This greatly simplifies installation: firstly, the material is simply spread over the surface and secured, and secondly, no unnecessary seams are formed.

Review of manufacturers: Izover, Knauf, Ursa

How to choose the right roll insulation for your roof How to choose roll insulation. Types of roll insulation. What are the advantages of rolled foil insulation. Characteristics of roll

Popular manufacturers

Products on the market various manufacturers. Each brand has its own characteristics and advantages.

Knauf

The German manufacturer offers a material that does not contain formaldehyde. Knauf products are safe for people. Mineral wool does not cause allergies, but it should be installed with gloves. Microscopic fragments included in the insulation can cause skin irritation.

Knauf roll materials are not of interest to insects and rodents. In addition, they are able to protect against external noise due to their good soundproofing characteristics. They are characterized by low thermal conductivity and good air permeability. The company offers materials for protecting walls, slabs, pipes and other surfaces in dachas and country houses.

Izover

High density insulation. The French manufacturer offers products of various thicknesses: from 20 to 150 mm, which significantly expands the possible area of use of Isover insulation.

The company's catalog presents thermal insulation material with foil, which is often used for insulation pitched roofs, walls, ceilings, installation of heated floors not only in houses, but also in baths and saunas. In terms of flammability it corresponds to the first class.

Ursa

High-quality professional insulation with a long service life. Has excellent soundproofing characteristics. Does not burn. When exposed to flame, it does not emit toxic substances. It does not break or crumble during installation. Pleasant to the touch.

When insulating the walls of private houses, M-11 is most often used. When performing thermal insulation work in an industrial complex, preference is given to P-30.

Topizol

The insulation can have a thickness of 3 – 20 mm. Suitable for various climate zones, including regions with high humidity. Doesn't rot. It has good vapor permeability. When ensuring sufficient tightness of the seams, it can withstand gusts of wind.

Used to protect walls, roofs, including attics, and floors. It is lightweight, which facilitates transportation and reduces the requirements for strength characteristics insulated surface. Able to maintain its performance characteristics for at least 30 years.

Installation can be done independently without special equipment.

Penofol

Multilayer foil material comes in several types. Type A provides for the presence of one foil layer. Type B has self-extinguishing polyethylene between layers of high-quality aluminum foil. Type C comes with a special adhesive base, which greatly simplifies its installation. Type A has the lowest cost and the least rigidity.

Penofol's foil thickness is 12 - 30 microns with a base thickness of 2 - 10 mm. To insulate surfaces operating in fairly harsh conditions, material up to 40 mm thick can be used.

Eco-friendly, safe, suitable for insulating children's rooms.

Scope of application of roll insulation

Roll insulation materials are used for thermal insulation of vertical and horizontal surfaces. Foil material is indispensable for creating thermal insulation in bath rooms, as it retains heat well and has heat-reflecting properties. This material has also found wide application for thermal insulation of individual structures, joints, and in hard-to-reach places.

Let's look at the main ways to use rolled heat insulators.

Rolled thermal insulation for walls

Rolled wall insulation can be used as a heat-insulating material applied under decorative finishing, including under wallpaper.

The application technology is very simple:

self-adhesive material is glued to a wall that has been prepared in advance, leveled and cleared of debris and old finishes;
a cement-based adhesive is applied to the heat insulator layer, its properties reminiscent of liquid plaster;
After the adhesive has hardened, you can begin gluing the wallpaper.

The use of such material for wallpaper will significantly increase the heat-retaining properties of the walls, as well as their sound insulation.

Rolled floor insulation

It is used as a substrate for various types of decorative floor coverings. It not only has heat-insulating properties, but also gives the floor “softness”, eliminates squeaks and sounds when the floor covering shrinks and moves.

In some cases, a foil thermal insulator can be used to insulate the floor; this will increase heat retention; however, the cost of materials reinforced with foil is 30–60% more expensive.

The technology for performing floor insulation work using foamed polymer in rolls is very simple:

the material is glued to a wooden floor or concrete screed using adhesive composition or self-adhesive properties;
leveled so that there are no “bubbles”;
The floor covering is laid on top.

The advantages of such a heat insulator include ease of installation, lack of debris, durability and environmental Safety. When choosing a roll insulation for the floor, it is worth remembering that the “softer” the floor covering, the denser the insulation should be.

In other words, it is better to use a polymer with maximum density under linoleum, otherwise when you walk you will “sink” into the floor covering, but under laminate or parquet you can lay a polymer with any density.

Rolled roof insulation

Suitable for thermal insulation of pitched and flat roofs. A roof insulated with such material will remain warm for several decades. You can install thermal insulation on our own, without attracting highly paid specialists. The heat insulator is located between the elements of the roof rafter system, and distortions, the formation of waves and other defects are not allowed.

In some cases, for example, when insulating residential attic room or in regions with cold climates, it is recommended to lay insulating polymer in two layers.

The technology for installing roof insulation depends on design features. Best option when thermal insulation is calculated at the design stage. In this case, the work boils down to rolling out the rolled material and gluing it to the inner surface of the roof, laying a layer of vapor barrier material on top and installing final finishing, for example, siding, lining, etc.

Application of roll insulation

This technology is far from perfect and creates only an illusion real savings material resources, since in fact this type of insulation is inferior in all respects to such sprayed analogues as polyurea

Another difficulty is the application technology. It should be mentioned right away that all surfaces must be prepared: thoroughly cleaned or even washed. Even minor pollution can lead to negative consequences. Self-adhesive insulation is applied similar to adhesive tape, but this method is less effective. Over time, the glue loses its properties, especially under the influence of temperature changes, and the material peels off. Fused insulation is applied using a gas torch. This is a slow and painstaking process, but the grip is somewhat better, although there is no guarantee that it will not give way in some places.

Regardless of whether roll waterproofing of the floor or any other surfaces will be carried out, this process takes a lot of time and effort. Accordingly, the deadline for putting the facility into operation is being delayed. And this work is not cheap. Therefore, this technology is far from perfect and creates only the illusion of real savings in material resources, since in fact this type of insulation is inferior in all respects to such sprayed analogues as polyurea.

Advantages and disadvantages

The main advantages of rolled material are:

Versatility. Suitable for thermal insulation of any surfaces. For complex spatial shapes, including curved ones, you can cut out a suitable piece.
Minimum requirements for surface preparation before installation.
Benefits in terms of material price and work productivity when insulating large areas of walls, especially straight sections.

Roll materials have disadvantages.

High labor intensity when laying in frequent lathing; additional time is required for cutting.
Low rigidity does not allow them to be used where it is necessary to withstand significant loads.

In general, the advantages compensate for the disadvantages, which explains the high popularity of roll materials among consumers.

The materials are harmless to health provided they are used correctly and fire safety regulations are observed.

Types of roll insulation

Mineral wool

Available in several modifications. A common disadvantage is hygroscopicity. All insulation materials must be protected from direct contact with liquids; the difference between them is only in the intensity of its absorption.

Glass wool. Pros: one of the cheapest (made from broken glass that has been melted down), unattractive to rodents and insects (often used when installing heated floors). Increased density, the ability to dampen sounds, and resistance to combustion add advantages to glass wool in use. The downside is the complexity of working with the material. When installing glass wool-based roll insulation, you cannot do without protective equipment. And not only the respiratory and visual organs; you need thick, closed clothing - microscopic fractions of glass penetrate literally everywhere.
Slag-like. It is also based on waste, but from the metallurgical industry. In terms of cost, this insulation is comparable to glass wool (even somewhat cheaper), but in terms of resistance to high temperatures it is inferior. But in terms of thermal conductivity it is the leader among mineral wools. In all other characteristics, it is approximately on the same level as other insulation materials of this group. Cons: absorbs moisture (increased hygroscopicity), does not dampen noise well.

There is also a drawback that makes using slag wool for insulation metal pipes inappropriate. It is not recommended to be used for thermal insulation due to residual acidity - it has a destructive effect on steel.

Basalt wool. The raw materials are processed rocks. Pros: ability to withstand high temperatures (up to +700), optimal combination thermal conductivity/density characteristics. The peculiarity of the material is that after getting wet it does not lose its thermal insulation properties (although there is a limit on the percentage of humidity), it is characterized by high sound absorption, fire-resistant, and “eco-friendly” (safe for allergy sufferers).

There are few downsides: this insulation requires high-quality vapor barrier, which cakes over time.

Any of the listed thermal insulation materials is also sold in a “foil” modification. The thinnest layer of aluminum increases the heat-reflecting properties of the product and protects it from contact with moisture.

Polymers

All roll insulators are made on the basis of foamed polyethylene or polypropylene. They differ in characteristics, but given the small thickness of the canvases, the difference in thermal conductivity between them is not particularly significant, so they can be considered identical. The most advertised, although not the only representatives of this group of elastic insulation materials on the market: Penofol (PE) and Penotherm (PP).

Russian products under the brands Energoflex, Energofloor, Jermaflex ( combined material) from ROLS ISOMARKET. It is relatively new on the market, but judging by the exchange of opinions on the Internet, it has proven itself to be an effective and versatile insulation material. Its quality was also appreciated by specialists.

The main role is given to the metallized layer. It is the foil that prevents heat rays from passing through the material. The heat insulator is covered with it on one or both sides; The choice of option is determined by the application conditions.

When choosing insulation from an unknown brand, you may encounter a substitution of concepts. To reduce costs, some manufacturers apply metallized spraying to the thermal insulation instead of a layer of foil. Such a screen is not durable, and is significantly inferior in efficiency to an aluminum coating.

So which option is better to choose cotton wool or polyethylene foam?

The main point that is important to understand is that foamed polyethylene or polypropylene in the form of rolls is precisely thermal insulation, that is, a material whose purpose is to slightly improve the characteristics of walls, and not to fully insulate them. Regardless of where it will be fixed - from the inside or from the front part

But basalt wool is already a real insulating layer. True, if used indoors, the wall will still freeze, but noticeably less heat will escape from the room.

It turns out that foam propylene from the inside will give less effect than cotton wool, since the temperature will only rise by a degree and a half. And even if you do outdoor installation, then the “picture” will be the same, but with only one positive thing- the wall will freeze a little less and condensation from the room will disappear.

At the same time, the material has an undeniable advantage - it is cheap and very easy to install. It is more difficult and expensive to work with cotton wool because you will need to make a false wall (usually drywall) to protect the basalt fibers, and in addition, it is important to take care that moisture does not get into the structure of the material. If this happens, then the effect of all the work done will be zero, since all the thermal insulation qualities will very quickly disappear.

Here it seems that cotton wool is better anyway (because it’s “warmer”), but everything is decided by the nuances of the situation. Yes, cotton wool seems to be good, but what is the point in it if, for example, you need to insulate a shower room not in the house, but, for example, in the country and you don’t want to invest? The obvious budget solution in this case is a metallized insulator - stick it on the wall and forget it.

But in the case of a more or less capital approach, but again in the absence of significant financial resources, it is better to opt for mineral wool and insulation from the inside. It turns out that ideal option No, and you need to make a decision only based on the specifics of the project.

Manufacturers of thermal insulators and their products

Roll insulation from several manufacturers is in greatest demand among consumers.

Knauf is a German brand whose products do not contain formaldehyde, which makes the finished product absolutely safe and harmless, which is important during installation work.

Insulation from Knauf

Isover is a French manufacturer that offers a wide selection of roll insulation with excellent performance characteristics, including foil-coated ones. The product is suitable for carrying out insulation measures both indoors and outdoors; it is not subject to combustion and can be extinguished in a fire.

Insulation for external and internal work

TechnoNIKOL is a Russian manufacturer offering high quality products at quite affordable and affordable prices. These roll insulation materials are produced on the latest equipment using innovative technologies and techniques, which makes it possible to guarantee not only quality, but also a long service life.

Classes and types of roll waterproofing

Produced roofing waterproofing Depending on the purpose, quality, components used and price category, they are divided into several classes.

Material class	Name	Price range	Characteristics	Purpose
Premium	Technoelast	100-160 rubles/m2 For models with a noise-absorbing effect - price up to 250 rubles/sq.m.	Welded coating with application of bitumen and SBS modifier. Used at temperatures from -50 to +1000C.	Lower/upper layers of roofing, underground communications.
Technoelastmost	235-250 rub./sq. meter.	The canvas is 5-5.2 mm thick, heat resistance level is up to +1000C. Filler – bitumen with artificial rubber (SBS). High-strength coating, service life - up to 40 years.	Waterproofing of concrete slabs on the carriageway of roads or in the form of an adhesive layer on the spans of bridge structures.
Business	Uniflex	85-130 rub./sq. meter depending on the thickness and type of base.	Welded coating with SBS-modified bitumen filler. Damage resistance, durability. The expert period between repairs is at least 18 years. The flexibility of the material is maintained at temperatures down to -200C.	Laying the top and bottom layers of the roof, repairs roofing, waterproofing of foundations, basements, ground floors.
Standard	Bipole	70-90 rub./sq. meter	Fused material, binder layer 1.5 mm thick. Withstands temperatures from -150C to +850C. The top layer of coating is shale chips. Service life – 5 years.	Used as the first layer of roofing or for the top part of the roof. Residential roof repair.
Bicroelast	67-84 rub/sq. meter.	Fused material based on fiberglass, fiberglass or polyester. Protective coating - shale chips or film. Thickness 3-4 mm, remains flexible at -100C.	It is used as a lining material for roofing and waterproofing of various types of structures - buildings, tunnels, bridges. Variety “K” is used to cover the top layer of the roof.
Economy	Bikrost	55-85 rub./sq.m.	Welded coating with bitumen filler. Flexibility is maintained only at positive temperatures, heat resistance is up to +800C. Thickness 3-4 mm, service life - up to 10 years.	Waterproofing, installation of the lower/upper layer of the roof - depending on the coating.
Euroroofing material P	13-16 rub./sq.m.	Fiberglass based coating with modified bitumen applied. The protective coating is applied to both sides of the insulating sheet. The thickness of the protective layer is 2-5 kg/sq.m.	Waterproofing of building structures, installation and repair of roofing carpet in buildings.

The building materials market presents a wide range of models of rolled waterproofing coatings - both universal and intended for a specific type of work.

Characteristics

Thermal insulation material in rolls, produced under various brands, is characterized by general characteristics.

Environmental friendliness

The insulation meets regulatory environmental safety requirements.

As a rule, it contains salt heavy metals, alkalis, acids, oxides, phenols or toxic organic compounds that are inactive at room temperature are present in minimal quantities.

Due to its low chemical activity, thermal insulation practically does not interact with aggressive environments, and therefore, for example, is not afraid of exposure to solvents.

Biological resistance and fire safety

The material has a high level of biological resistance. As a result, there are no rodents, fungus, or mold in it. It is of no interest to insects and animals as food. Depending on the composition and other characteristics, the insulation can withstand high temperatures.

Air and vapor permeability

If insulation is used to insulate floors or walls, air permeability is an important indicator.

When using rolled materials, you do not have to worry about excessive dampness in the room, condensation and other negative phenomena, provided that the installation is done correctly.

When going shopping, it is worth remembering the following aspects of your choice:

Various variations of insulation are suitable for indoor and outdoor use.
The surface that will be covered with roll insulation also matters. There is a fundamental difference between the materials used to insulate the ceiling and walls. Each of these bases has its own insulation.
It is also important to remember what material the walls are made of. A thermal insulator for a wooden base may not be suitable for a concrete base and vice versa.
When choosing the thickness of the material, it is worth taking into account the temperature conditions in winter and the climate characteristics for a particular region.
Before purchasing, you should definitely familiarize yourself with the quality certificates and other permitting documentation for the selected roll insulation, and in addition, make sure that the packaging is intact. Moisture, even in small quantities, can negatively affect the calculated parameters of the material and its properties.

Choose high-quality material from trusted manufacturers

3 Rolled foil thermal insulation

Rolled foil insulation on the market is usually made either from polyethylene foam (the fairly popular brand Penofol) or from polypropylene (Penotherm).

These are two almost identical materials, the difference between which lies only in physical and mechanical characteristics. If we consider only those that affect the direct effectiveness of use as a thermal insulation material, then foil roll insulation for walls based on polypropylene appears more preferable.

Thus, the polypropylene base has an order of magnitude lower thermal conductivity (a difference of about 30%), less moisture absorption and better resistance to external mechanical influences.

In fact, the last factor can be neglected, since foil insulation materials themselves, due to their minimum thickness, do not fulfill effective insulation when the foil is damaged, so it is important to look at the quality of the foil coating. .

Rolled penofol with one-sided foil

Unscrupulous manufacturers, in order to reduce the cost of products, may not use aluminum foil as a shielding layer, as required by technology, but ordinary metal spraying.

The efficiency of such spraying is much lower than that of foil, and the cost of such products sold under the guise high-quality insulation materials, comparable to quality products from trusted manufacturers. When choosing foil-covered insulation for walls, floors, or pipes, carefully check the quality of the shielding layer.

High-quality foil thermal insulation has the following advantages:

High heat shielding coefficient, about 97%;
Wide functionality - foil materials are used not only for household insulation of walls, floors and ceilings, they are also widely in demand for thermal insulation of all kinds of industrial equipment;
Minimum roll weight;
Easy to install - foil thermal insulation does not require frames, anchoring and similar frills; it sits on the wall using polyurethane foam or regular construction adhesive;
Minimum cost - the price of foil materials is significantly lower than that of mineral wool;
Complete vapor barrier;
Safety for the human body.

Foil thermal insulation has only one significant disadvantage– it is subject to combustion. The operating temperature of polypropylene is 150 degrees, polyethylene foam is 80 degrees.

3.1 Features of thermal insulation of a balcony with foil roll insulation (video)

Characteristics

Rolled insulation materials are characterized by the following main parameters:

Environmental friendliness. All models on the market must comply with safety requirements for installation, operation and disposal. They must contain small amounts of harmful substances; these substances must not be released from the insulation during its storage, installation and during use. The packaging indicates the disposal method. The materials are resistant to organic solvents and other active substances.
Fire and bioprotection. Mineral insulation does not burn on its own and prevents the spread of flame. Foam materials can withstand fire for a certain time. The materials prevent the formation of mold and repel rodents.

Air and vapor permeability. Key characteristics. They show how much air or water vapor at a certain temperature can leak through a unit area of material. Vapor permeability is necessary in order to remove excess moisture from the room to the outside through the walls and their ventilation systems.
Strength. An important characteristic of insulation under wallpaper. Touching, including with hard objects, should not damage the wallpaper.

Which roll insulation to buy

Roll insulationis the name of a whole class of lightweight thermal insulation, widely used in civil and industrial construction. They are made from staple fiberglass with the addition of various binding materials, fillers, water repellents (substances that repel water), which give them softness, elasticity and resilience. Rolled thermal insulation is the most inexpensive of all types of insulation, and therefore is in consistently high demand among builders.

This section of the site presents roll insulation, their price and parameters of the rolls. All product information from different manufacturers given on one page. Here you will find short description each of them.

ROLL INSULATIONS URSA

This is a very famous line of insulation European manufacturer- concern "URALITA". URSA brand roll insulation materials are soft elastic mats made of staple fiberglass. Each brand has its own marking, which allows customers to easily navigate the characteristics of the material and, accordingly, its purpose. URSA insulation materials are high-quality lightweight insulation materials recommended for use in horizontal unloaded building structures. Good thermal characteristics, ease of transportation and installation make them in great demand for many years.

A special place in the line of roll insulation products of the URSA Concern is occupied by new generation insulation materials under the URSA PUREONE trademark (in rolls and slabs). Acrylic, a neutral and safe polymer, is used as a binding component. The production technology of these insulation materials excludes the use of phenols and formaldehydes, which makes them particularly environmentally friendly. They are widely used in Europe, America, Japan for heat and sound insulation indoors. In Russia they also gained well-deserved popularity.

KNAUF ROLL INSULATIONS

These are natural mineral wool insulation materials made using innovative ECOSE technology. During the manufacturing process, binders based on natural components are used, so it has a pleasant color of natural flax and a structure that is pleasant to the touch. Due to environmental friendliness, such insulation can be used indoors.

You can always contact our specialists, who will tell you where you can find additional information about the insulation you are interested in or give advice on installing the material.

Installation technology

The technology for installing roll insulation is slightly different from slabs. They begin to insulate the walls or floor initially. The walls are mainly made of slabs, as is the straight ceiling. Therefore, often, floors and pitched ceilings-walls are suitable for insulation and installation. When insulating the floor, it is worth looking at what type of insulation is available.

Insulation in foil is mainly used, but sometimes rolls of insulation are covered with ordinary heat-insulating foil or metal film. The insulation should extend 1 cm away from the walls. This is due to the fact that when temperature changes, the material contracts and expands. The lack of free space in metallized or foil insulation leads to its deformation and damage over time.

Ceiling (pitched) insulation is attached between the rafters, cutting out a little more in order to insert it better between the boards. They are inserted strictly from bottom to top to avoid voids. After installation, the surfaces are clamped with main profiles or boards for application of additional (for example, vapor barrier) materials on top. The work is carried out especially carefully.

Let's move on to installing walls with roll-type insulation from the inside. It is produced by preparing walls for pasting. A special glue for cotton wool is diluted; the wall should not be covered with putty or plaster; only bare concrete or brick is allowed. The composition is applied to the wall evenly using a special comb, after which they begin gluing the rolls, which can be cut for convenience.

In this case, it is advisable to make the wall itself level, flat, if there are no further plans for sewing it into a box or gluing glass wallpaper. After the material is mounted on the wall, you need to screw it on. Each petal should be slightly recessed in the cotton wool. At least 5 fixing holes are required per 1 m2. It is better to fasten the sheets themselves and the space between them (in this case, both sheets will adhere, which will avoid warping and ensure level and plane).

After the sheets have set, a layer of glue should be applied. The technology is reminiscent of puttying, only with a different solution

It is important to monitor the level and plane. It is necessary to make at least two passes, since it will be problematic to lay a good layer the first time

After leveling, regardless of the type of room, you can proceed to the next work. When installing plasterboard sheets inside the house, they are attached using dowels to a layer of thermal insulation, which should preferably be treated with glue, as in the previous paragraph.

About the advantages of URSA roll insulation, see the video below.

Operational imperfections and maintenance difficulties

Each type of waterproofing material has its own unique features. Thus, TechnoNIKOL, which, according to the manufacturer, can withstand heavy mechanical loads, may not withstand increased soil mobility. Therefore, many people use a modification for waterproofing road substrates from the same manufacturer. But these are unjustified costs.

As for maintenance, for example, if the polyurea coating is damaged, it is enough to simply spray a small layer locally on the area. But roll waterproofing that has peeled off in any place requires serious repairs. It is necessary to remove it, at least in this place, prepare the base, reapply insulation, covering the resulting seams. Of course, we are not talking about any aesthetics, and the quality of such a patch will be far from perfect.

Waterproofing with roll materials is not universal. So, with their help it is impossible to treat surfaces complex shapes, for example, the underbody of a car. And even roll roof waterproofing can become a serious problem. In addition, high temperatures have a detrimental effect on this material and the degree of its adhesion to the base.

The main disadvantages of waterproofing with roll materials in specific conditions:

Rolled roof waterproofing – impossibility of processing surfaces of complex shapes, long application process, susceptibility negative impact temperature changes, difficulty of maintenance
Rolled floor waterproofing – poor perception of constant mechanical loads, especially in vibration conditions
Rolled foundation waterproofing – instability to the negative effects of moving soils, additional load on the foundation, which is undesirable in areas with high groundwater levels and in loose soil foundations

Characteristics of basalt wool

If it doesn't suit you insulation under wallpaper rolled, which was discussed above, then you can choose basalt or fiberglass wool, which has a wide application potential. It can be installed on walls or floors, as well as on ceiling spans. It is not recommended to use this material for sloping roofs, this is due to the fact that over time the mass slides and the insulation density is broken. If you want to use this flooring, you need to lay at least two layers. This will allow you to get 1 decimeter of thickness. If there is a need to insulate the walls, then half the amount should be used, and laying the material in one layer will be sufficient. If you want to achieve an effective heat-saving screen, then you should use similar thermal insulation with vapor and waterproofing.

What to consider when working

Insulation with mineral roll materials can be carried out at any time of the year, it is only important to ensure that the material is protected from precipitation. . The use of foam materials mounted on an adhesive layer depends on the air temperature

Usually the limit is down to –10C. Special adhesives are also produced that are effective down to –20C.

The use of foam materials mounted on an adhesive layer depends on the air temperature. Usually the limit is down to –10C. Special adhesives are also produced that are effective down to –20C.

Before insulation begins, minimal surface preparation is required:

Dismantle pipes, electrical wiring, lamps, decorations, plants, etc.
Clean the walls from remnants of old coatings, debris and dust.
Install lathing for mineral insulation.
Level and clean the surface for gluing foam thermal insulators.

Installation does not require special equipment; the tools you will need are:

construction knife;
stapler;
screwdriver;
hammer;
double sided tape.

It is more convenient to carry out installation and cutting of roll insulation together by two people, especially for large volumes of work. Small volumes can be done by one master.

Insulation process

The sequence of operations when installing mineral insulation is as follows:

A vapor barrier film is attached to the prepared wall.
The sheathing is made of wooden bars or metal profiles. The recommended guide pitch is 50 or 60 cm.
Rolls are cut in accordance with the selected pitch. The cutting must be carried out so that the insulation fits tightly between the guides and, when straightened, provides a better fit to the guide.

Disc dowel

Mineral wool is attached to the wall using disc-shaped plastic dowels, cut according to the thickness of the layer at the rate of 4-5 per square meter.
The windproofing film is attached to the guides on top of the laid cotton wool. The joints of the film are sealed with double-sided tape. Installation of insulation on the walls of the house.
Installation diagram under the sheathing
Thermal insulation is complete. You can proceed to the installation of the selected cladding - wooden or vinyl siding. To ensure ventilation of the facade, a secondary sheathing of thin slats is installed on top of the wind barrier.
Installation diagram for plaster
Read on the topic -.
Installation of rolled foam insulation for external and internal walls is simpler in itself, but requires better surface preparation. It will have to be leveled more carefully - foam will not be able to hide unevenness as much as mineral wool.
It is not recommended to fasten foam rolls using a construction stapler - the staples create so-called thermal bridges through which cold can penetrate into the warm part of the room. The thermal insulation effect of the material is somewhat reduced.
How to fix insulation to the wall:
- Clean and level the wall surface.
- Cut the material for end-to-end installation.
- In places of complex spatial shape - near openings, in corners, junctions of building structures (beams, balconies, etc.) it is better to try on the cut pieces before applying glue or removing the protective layer.
- Apply glue to the heat insulator or remove the protective film from the adhesive layer.
- Glue the material, moving from bottom to top.
- Smooth the surface with your hands or a rule, achieving the best fit. If large air bubbles have formed, they should be carefully pierced in the center with a sharp needle and, moving from the edges of the bubble to the hole, squeeze out the air.
After half an hour, the glue will set and the thermal insulation layer will be ready for use. When installing a cork sheet, glue specially designed for cork is used. It is applied both to the wall and to the cork. Before gluing wallpaper, you should wait until the glue has completely dried to avoid warping.

2 Rolled thermal insulation based on mineral wool

The quality of this category of insulation is regulated in accordance with the requirements of GOST RF “52953-2008”. This quality standard allows the following thermal insulation material to be classified as mineral wool insulation:

Basalt wool is a material produced by melting rocks and then forming microscopic fibers from them, connecting them into a solid carpet;
Slag wool is a material made from waste from the metallurgical industry. As a rule, it costs much less than basalt wool;
Glass wool is a morally obsolete material, but still quite often used due to its low price. Produced by melting cullet.

Rolled basalt wool has a characteristic yellow tint

Rolled insulation based on mineral wool, due to its elasticity and flexibility, is extremely universal material, which can be successfully used both for thermal insulation of walls, floors, attics, and other flat surfaces, and for thermal insulation of pipes.

2.1 Mineral wool production

Let's look at the technology for making mineral wool using an example basalt insulation. Rock basalt rocks, chemical composition which meets GOST requirements, can be melted in two ways - hot and cold.

The hot method involves heating basalt rocks in blast furnaces, the cold method involves exposure to electromagnetic radiation (like a conventional microwave).

The molten rock is fed into a centrifuge, which is equipped with constantly cooling carbide disks. Under pressure, molten basalt is fed into a centrifuge and falls onto rotating disks, where individual basalt fibers are formed from the melt through the process of cutting cooling and pressure drop.

The resulting fibers are immediately removed from the drum by a special functional element and supplied via a conveyor to a laying machine, which forms a carpet of basalt wool of the required thickness.

After laying the carpet, the fibers are impregnated with various impurities, which are necessary to give the final product the required characteristics - hydrophobicity, fire resistance, density and elasticity.

Slag material, as a rule, has a darkish tint

2.2 Advantages and disadvantages

Among all the thermal insulation materials on the market in the middle price category, it is mineral wool that has the lowest thermal conductivity. Although the leaders in general are polystyrene foam and mineral wool.

An important factor is that thermal insulation properties mineral wool do not depend in any way on any external conditions– this material does not expand under the influence of moisture, is not subject to thermal expansion, and microorganisms and rodents do not grow in mineral wool.

Rolled mineral wool insulation is produced with a wide variety of performance characteristics - you can choose either low-density mineral wool for insulating pipes and other uneven products, or dense material for thermal insulation of surfaces that experience external loads - the floor or attic floor.

An important advantage of mineral wool is its fire resistance. This material can withstand temperatures up to 700 degrees; it does not ignite even under direct exposure to fire. It is also worth noting good noise-reducing properties - by insulating walls and floors with rolled mineral wool, you will solve not only the issue of insulation, but also sound insulation of the house.

The only drawback of mineral wool is its high vapor conductivity, due to which the installation of a special vapor barrier film is required when installing this insulation.

Thermal insulation of the pipeline using rolled glass wool

Rolled mineral wool insulation can be used for the following purposes:

Insulation of roofs, floors, walls, and any flat surfaces;
Thermal insulation of pipes and pipelines;
Thermal insulation of industrial equipment;
Insulation element inside sandwich panels (here the best thermal insulation is Hitrock);
Internal insulation in false walls and when laying hollow walls;
External insulation of house walls followed by plastering.

The ROVEN company offers to buy pipe and roll thermal insulation rockwool in Sevastopol at a competitive price. We invite you to visit our office at: Sevastopol, Fiolentovskoe highway, 1/2, letter L, office 105 (territory of the Mayak plant). Call by phone +7 978 117 57 03 , our specialists will answer all your questions.

Plain and laminated mineral wool cylinders with a synthetic binder Rockwool cylinders are pipe insulation, which is a hollow product made from basalt group stone wool (simple). Rockwool cylinders can also be produced with an aluminum coating (laminated).

Pipe and roll thermal insulation Rockwool
Roll insulation: types and features of roll insulation
1. Thermal insulation based on roll insulation
2. Advantages of thermal insulation in rolls
3. Types and characteristics of thermal insulation in rolls
4. Heat insulator with foil surface: features
5. Tips for choosing thermal insulation in rolls: what you need to know
Review of characteristics of insulation in rolls
How to choose the right roll insulation for your roof
1. Scope of application of insulation in rolls
2. Types of insulation
3. Review of manufacturers: Izover, Knauf, Ursa
Roll insulation
1. Scope of application of roll insulation
2. Thermal insulation roll materials made of mineral wool
3. Roll insulation Penofol

Low thermal conductivity and high thermal insulation properties
High biostability and chemical resistance (to solvents, oils, acids and alkalis)
Extended operating temperature range (melting at temperatures above 1000°C)
High temperature does not affect the thermal insulation properties of the material
There is a longitudinal cut for ease of installation, easy to cut with cutting tools

Technical characteristics of Rockwool pipe insulation

λ125 = 0.048 W/(m K)

λ300 = 0.087 W/(m K)

Flammability group Rockwool

NG, with foil coating - G1

Application temperature Rockwool

from -180 to +650 °C

Acidity module, not less than Rockwool

Rolled thermal insulation

WIRED MAT 80 is made from stone wool based on basalt rocks. One side of the mat is covered with a mesh with 25 mm cells made of galvanized or stainless wire. In addition, the mat is stitched with galvanized or stainless steel wire (SST). The product can also be produced with one-sided coating with aluminum foil (ALU WIRED MAT 80).

TECH MAT – lightweight hydrophobized mats with a synthetic binder, made from stone wool based on basalt rocks. On one side, the mats can be covered with aluminum foil.

Application:

WIRED MAT 80 is used for thermal insulation of technological and energy equipment, heating networks, main and industrial pipelines with temperatures up to 750°C.

ALU WIRED MAT 80 is used for fire protection of air ducts.

TECH MAT – used for thermal insulation of pipelines and industrial equipment. Maximum application temperature +570°C.

Pipe and roll thermal insulation Rockwool ROVEN offers favorable prices for pipe and roll thermal insulation rockwool in Sevastopol. Description, technical characteristics, photos.

Symbols for roll waterproofing brands

In addition to the name of the model of waterproofing material, the name contains letter markings. Each of the letters denotes a specific feature inherent in this brand of waterproofing agent, based on the use of a specific base and the characteristics of the protective layer.

Thus, roll insulation Uniflex model HPP stands for a material with a fiberglass base, covered with a protective film on both sides.

Rolled waterproofing TechnoNIKOL

Rolled waterproofing, produced under the TechnoNIKOL brand, occupies a leading position in the ranking of building materials on the international market. The reason for the popularity of TechnoNIKOL brands are:

high degree of reliability and effective protection against moisture and condensation;
biological and chemical resistance, maintaining flexibility and elasticity at low temperatures;
ability to withstand significant tensile load;
long-term service life - from 35 years;
ease of installation, cost-effective.

The strength of TechnoNIKOL waterproofing products is due to the use of a multilayer structure consisting of a polyester base, two layers of bitumen-polymer filler and protective film. All coatings are produced in strict accordance with GOST and current building regulations.

Under the TechnoNIKOL brand, new models of roll waterproofing are being developed, taking into account different climatic conditions and the production capabilities of the consumer. Baseless self-adhesive roll coatings are widely used for waterproofing floors and foundations.

In addition to protection from moisture, waterproofing coatings from TechnoNIKOL are capable of protecting premises from noise, dust, and harmful gases.

Roofing and insulation materials are used both in the construction of new buildings and in repair and restoration work. The scope of application of waterproofing materials from TechnoNIKOL includes:

strengthening foundations under industrial structures;
construction of high-rise buildings;
waterproofing of private households from the destructive effects of dampness and moisture;
construction of tunnels, viaducts and bridges using reinforced concrete slabs.

Modern roll materials for waterproofing can effectively and reliably protect a building or structure from groundwater, freezing and precipitation. Right choice waterproofing material, strict adherence to the recommendations of specialists and installation technology are the basis for successful installation of roll waterproofing and the durability of the structure.

Review of manufacturers Izover, Knauf, Ursa

The quality of the insulator undoubtedly depends to some extent on the manufacturer.

knauf-1
knauf-2

Knauf - product German manufacturer, created from natural mineral wool latest technology ECOSE. It is an environmentally friendly insulator because it does not contain formaldehyde. Even with direct contact with this material, it remains safe for humans and does not cause allergies. It can even be used for interior spaces. This is reliable protection from cold and noise.

Distinctive characteristics of Knauf materials:

high degree of vapor permeability;
low water absorption;
chemical and biological inertness.

isover-1
isover-2

French insulation isover. This is a relatively cheap option for roof insulation. This is the densest material among its analogues. Available in rolls of different thicknesses: 2, 3, 5, 10 and 15 cm. What are the advantages of Isover Classic roll insulation? Reviews show that he

excellent sound insulator;
environmentally friendly;
does not burn, does not produce toxic emissions when exposed to an open flame;
durable;
easy to install.

ursa-1

Ursa is another popular brand. It is distinguished by its durability, does not break or crumble, and is easy and simple to work with. Available in various widths: 5; 8 and 10 cm.

Types and characteristics

Mineral wool insulation materials are widely used.

Their popularity is explained by their high operational and technical indicators and relatively low cost.

Roll insulation based on mineral wool includes:

. The material is obtained by melting rocks of a certain type and forming thin fibers.
Glass wool. Insulation made from molten broken glass is affordable. Thanks to this, the material is in high demand, although it is considered obsolete.
Slag-like. The material is based on waste from the metallurgical industry, so it has a fairly low price.

Insulation based on mineral wool has its own distinctive properties:

temperature resistance;
low thermal conductivity;
high density;
absorption of vibrations and sound vibrations;
no shrinkage after long-term use.

Foil roll insulation is made from expanded polystyrene foam by applying it to a layer of foil. The foil creates the effect of a thermos, pushing heat back into the room.

Expert advice: foil insulation can be used when installing infrared floors and for thermal insulation of wooden saunas and baths.

The main properties of foil roll insulation include:

high thermal insulation;
reliable vapor barrier;
good noise absorption;
fire safety;
durability.

Intercrown roll insulation represents a rather specific solution. The main purpose is to fill the empty space between the crowns. Even high-quality assembly of houses from profiled timber or logs cannot guarantee a tight fit of the elements. An inter-crown heat insulator will fill the free space.

The material is produced in narrow rolls; natural and harmless materials such as flax, batting, and jute are used for its production. The use of this type of insulation is possible both during construction and during operation of the house. Everyone knows that over time, wood dries out, forming gaps between building elements. By filling the resulting voids with insulation using a chisel and mallet, you can retain maximum heat in the house.

Thermal insulators based on mineral wool

Flexibility makes work easier

Assortment and features of species

The term “mineral wool” is a unified designation for a whole range of heat insulators, namely:

basalt wool - for the production of this material, the technology of melting certain rocks is used, followed by the formation of the finest fibers on their basis, woven into a single carpet;
glass wool is a material, although it is considered obsolete, but still has a fairly high demand due to its affordable cost. For its production, remelted broken glass is used;
slag wool - it is based on waste obtained in the metallurgical industry. Due to this, such insulation in rolls has a lower cost than basalt and glass wool.

Glass wool in rolls

Basalt wool

Slag in rolls

The dimensions of the materials largely depend on the manufacturer, but most often they have the following standard sizes:

length – varies between 3-6 m or more;
width - standard 0.6 and 1.2 m, although products of individual brands may have a width of 1.22 m and 0.61 m;
thickness – 50, 100 and 150 mm.

Wall mounting

Despite the fact that roll insulation is created from different materials, it is mounted on the wall according to the standard principle. All differences will lie in the composition of the glue that will be used, and, accordingly, in the drying time of the substrate on the wall.

Conditions for carrying out installation work with the substrate indoors

To glue insulation to the walls of your apartment, you have to do the following:

First of all, it is worth preparing the surface, for which you need to remove the old wallpaper, plaster the wall, smoothing and sealing large gaps and unevenness. Small defects in the wall surface can be left, they will be closed.
Next, the surface of the wall must be primed. This is done either using glue, which we will use to glue the substrate, diluted in a weaker consistency, or using a special primer composition. After priming, you need to wait until it is absorbed into the wall and dries.
It is recommended to cut the rolled insulation into pieces required length in advance so that he can lie down and straighten out. This will make gluing it up a lot easier for us. When cutting the canvas, add a little material for insurance.
We prepare the adhesive composition according to the instructions on its package. If we are dealing with a substrate with top layer made of paper, then apply glue to the wall and to the cut pieces, while letting them soak in the composition for literally 5 minutes. If the backing is equipped with non-woven edges, then it is enough to smear the wall, and the material will easily attach to it.

Next, we proceed directly to installing the paintings on the walls. This process is reminiscent of wallpapering; the pieces are also glued together and carefully smoothed out. The air is expelled from under the canvas and it sticks firmly to the wall. It is convenient to use a rubber roller; it will create the necessary pressure and will not damage the insulation material.
After the insulation has dried, after about 1-3 days, seal the joints of the panels with regular masking tape. Krepp will allow us to give solidity to our structure.
Now our walls are well insulated, and we can proceed directly to gluing the wallpaper itself.

Wall insulation will allow us to create the most comfortable living conditions. It will serve us for a long time, no matter how long any wallpaper hangs.

This section of the site presents roll insulation, their price and parameters of the rolls. All information about products from different manufacturers is given on one page. Here you will find a brief description of each of them.

Brands of roll insulation Ursa/Ursa

This line of insulation includes the following brands:

Rolled fiberglass insulation Ursa Geo M-11 (roll 10000x1200x50 mm x 2 pcs)
Rolled fiberglass insulation with foil Ursa Geo M-11F (roll 18000x1200x50 mm)
Rolled fiberglass insulation with foil Ursa Geo M-11F (roll 9000x1200x100 mm)
Rolled fiberglass insulation Ursa Geo M-15 (roll 8500x1200x50 mm x 2 pcs)
Rolled fiberglass insulation Ursa Geo M-25 (roll 9000x1200x50 mm)
Rolled fiberglass insulation Ursa Geo M-25 (roll 4500x1200x100 mm)
Rolled fiberglass insulation with foil Ursa Geo M-25F (roll 4500x1200x100 mm)
Rolled insulation with acrolic binder Ursa PureOne 37RN (roll 10000x1200x50 mm x 2 pcs)

This is a very well-known line of insulation materials from the European manufacturer - the URALITA concern. URSA brand roll insulation materials are soft elastic mats made of staple fiberglass. Each brand has its own marking, which allows customers to easily navigate the characteristics of the material and, accordingly, its purpose. URSA insulation materials are high-quality lightweight insulation materials recommended for use in horizontal unloaded building structures. Good thermal characteristics, ease of transportation and installation make them in great demand for many years.

Brands of roll insulation Knauf/Knauf

Roll insulation TeploKnauf Dacha (7380x1220x50 mm x 2 pcs)
Roll insulation TeploKnauf Cottage (6148x1220x50 mm x 2 pcs)
Roll insulation TeploKnauf Insulation NH 040 (7380x1200x50 mm x 2 pcs)

You can always contact our specialists, who will tell you where you can find additional information about the insulation you are interested in or give advice on installing the material.

Properties of roll insulation

All roll insulation materials have approximately the same properties, which determine their widespread use, namely:

low thermal conductivity;
good sound insulation;
optimal hygroscopicity;
high water-repellent properties;
ease of transportation and operation;
resistance to aggressive media (acids, alkalis, solvents);
fire safety;
optimal price.

If they are used to insulate a pitched roof that has a frame supporting system made of wood or metal, the insulation is placed inside the frame. When working with rolled thermal insulation on vertical and inclined surfaces, it is necessary to use a lathing or frame. The insulation is installed with compression to cover the “cold bridges”.

Where to buy roll insulation

Roll insulation can be purchased:

wholesale and retail at our warehouse complexes in Moscow;
order delivery to the site;
combine all materials in one collection vehicle, which will deliver them to the site;
order wholesale delivery with free shipping

We cooperate with individuals and organizations from all regions of Russia. Check out the catalog and place an online order on our website. Our managers will answer all questions about the terms of cooperation by calling the numbers in the section.

BUY IN ONE PLACE, SAVE ON DELIVERY, TAKE USE OF REGULAR CUSTOMER DISCOUNTS

Articles By topic:

How and how long to bake beef Baking meat in the oven is popular among housewives. If all the rules are followed, the finished dish is served hot and cold, and slices are made for sandwiches. Beef in the oven will become a dish of the day if you pay attention to preparing the meat for baking. If you don't take into account	Why do the testicles itch and what can you do to get rid of the discomfort? Many men are interested in why their balls begin to itch and how to eliminate this cause. Some believe that this is due to uncomfortable underwear, while others think that it is due to irregular hygiene. One way or another, this problem needs to be solved.
Why do eggs itch? Minced meat for beef and pork cutlets: recipe with photo	Why do eggs itch? Schemes for launching spacecraft Orbits of artificial Earth satellites

1 2 3 Ptuf 53 · 10-09-2014 The union is certainly good. but the cost of removing 1 kg of cargo is still prohibitive. Previously, we discussed methods of delivering people into orbit, but I would like to discuss alternative methods of delivering cargo to rockets (agree with

2024-04-21 02:23:23	Popular
2024-04-14 02:26:43	Grilled fish is the most delicious and aromatic dish
2024-04-13 02:40:32	Yu. Andreev - Live Journal! Andreev Yu.A. Yuri Andreev: biography
2024-04-12 02:26:50	Master class for teachers on the topic “Creating electronic tests”; methodological development on technology on the topic
2024-04-10 02:23:37	The benefits and harms of protein for the body
2024-04-08 02:21:43	Miller's dream book: distinctive features and characteristic features See dream book interpretation of Miller's dreams
2024-04-05 02:30:06	Recipes for lavash rolls with different fillings (photo)
2024-04-05 02:30:06	Elder Pavel (Gruzdev) Elder Archimandrite Pavel Gruzdev
2024-04-01 02:23:38	Fried zucchini - the best recipes
2024-03-31 02:28:43	Organs of flowering plants Plant organs and their functions presentation

The structure of the molecule of ice and water vapor drawing

2024-03-29 02:26:33	New
2024-03-29 02:26:33	Ivan Krylov the best fables for children Various fables are interesting and easy to read
2024-03-28 06:32:57	The Life of Saint Veronica in Orthodoxy
2024-03-28 06:32:57	Meatballs with gravy in a frying pan
2024-03-26 02:24:23	An interesting story about yourself (All about myself)
2024-03-24 02:29:32	Eat honey, eat ginger - be healthy like a hero!
2024-05-31 02:21:07	Church of the Ascension in Kolomenskoye Temple of the Ascension of the Lord Great Ascension
2024-05-23 02:16:29	How and how much to bake beef
2024-05-10 02:22:08	Why do the testicles itch and what can you do to get rid of the discomfort?
2024-05-02 02:14:23	Minced meat for beef and pork cutlets: recipe with photo
2024-04-21 02:23:23	Popular
2024-04-14 02:26:43	Grilled fish is the most delicious and aromatic dish