≡× MENU

• Interior
• Window
• Walls
• Projects
• The buildings

Cheap fence for a summer residence - original fences made of wood, metal and scrap materials. What to make an inexpensive garden fence from? How to make a fence at the dacha

Profiled sheet – universal material for fencing, a fence from which can be easily built with your own hands. Advantages of a fence made of corrugated sheets:

• strength;
• Beautiful appearance;
• good sound insulation;
• big choice colors;
• ease of installation;
• long service life;
• low cost.

Installation of a fence made of corrugated sheets

Step by step, a fence made of corrugated sheets for a private house is made like this:

1. Marking the fence. Along the perimeter, markings are made of the places where the pillars will be installed (the distance between them should not exceed 3 m), as well as the places for the gate. For calculation required quantity using a profiled sheet, you need to decide how high the fence will be.
2. Installation support pillars. Material for supports – square pipe from 50x50 mm or round pipe with a diameter from 76 mm. The laying depth is from 1.0 to 1.5 m depending on the height of the fence. The width of the pits for supports is 150 mm. The bottom is covered with crushed stone or sand. The pillars are placed strictly plumb. The pillars are filled with fine-grained concrete or mortar.
3. Installation of logs. For logs you can use a profiled pipe 40x25 mm. The number of logs in the span depends on the height of the fence: if the height is 1.7 m, two logs are enough, if more, three. The logs are welded to the pillars at a distance of 4 cm from the ground and the top edge, and the middle one (if there is one) is fixed strictly between them. The logs are primed against corrosion before the corrugated sheet is attached.
4. Installation of profiled sheets. On soft soils, pillars and fences are placed on strip foundation. Along the fence to a depth of 20 cm, a tape box is made with waterproofing along the walls, which is filled with concrete. The corrugated sheet is attached to the joists with metal screws into drilled holes. You can use rivets. The supports can be covered with natural or artificial stone– the structure will become stronger and look more beautiful.

Sometimes poles made of wood or asbestos-cement pipes are used. Wooden posts must be treated with an antiseptic, and asbestos-cement posts should be used only for low fences.

For the sequence of installing a fence made of corrugated sheets with your own hands, see the video at the end of the page.

How to make a chain-link fence with your own hands

Chainlink fences are widely used in summer cottages - the mesh does not create shadows and does not interfere with air exchange. But the main advantage of Rabitz is its accessibility.

There are three types of Chainlink:

1. non-galvanized steel;
2. galvanized;
3. plasticized (coated with polymer).

There are two different ways make a chain-link fence:

1. stretch the mesh between the posts;
2. assemble frame sections from a corner with a mesh into a fence.

The first option is easier to manufacture, the second is more expensive, but more beautiful and functional.

Chainlink fence posts

Pillars can be made of several types of material:

• Wooden. Short-lived, but often the most cheap material. The column must be cleared of bark and buried 10-20 cm below the freezing level. The length of the pillar will be about 3 m. The underground part is treated with mastic for waterproofing, and the above-ground part is painted. The mesh on wooden posts is secured with nails.
• Metal. Most suitable material. Use round or square pipes 60 - 120 mm with a wall thickness of 2 mm. Sometimes they sell painted posts with hooks. This option will cost a little more, but will save time and labor costs.
• Concrete or asbestos-cement. The mesh must be secured to such posts with clamps or cables.
• Chain-link tension fence. Pegs are hammered into the corners of the site and the cord is pulled. The marking of the pillars is done based on the distance between them of 2.0 - 2.5 m. Dividing the total length of the cord by the pitch, we get the number of pillars. The step is taken so that the exact number is obtained. The places of future supports are marked along the stretched cord, making sure that they are in a straight line.

Attention! If there is a large slope on the site, then in places where there is a difference in height, the fence will have to be terraced, i.e. install a longer and more powerful pole in this place and secure the divided mesh sheet on both sides at different levels.

Installation of poles

In places marked for posts, holes up to 1.5 m deep are made with a hand drill, crushed stone is poured onto the bottom. 10 – 12 cm and compacted. First, install the corner posts. The depth of the pillar should be 20 cm below the soil freezing level. The underground part of the pipe is treated with anti-corrosion mastic and the columns in the pits are filled with mortar or fine-grained concrete. The verticality of the pillars must be controlled by a plumb line.

Attaching the mesh to poles

To attach the Chainlink to the posts, hooks made of wire, nails, etc. are welded. The net is hung on the hooks of the corner post. A thick wire or rod is inserted vertically into the first row of cells and welded to the pipe. The two of you stretch the mesh, holding on to a rod threaded a little further than the attachment point. The mesh is stretched as much as possible and put on the hooks. At the top and bottom of the mesh, 5–20 cm from the edges, a horizontal wire is threaded along the entire length of the span and welded to the post. For subsequent flights the procedure is repeated.

Attention! On corner posts, the mesh must be separated and secured separate canvas– this will reduce the load on the pillars.

All that remains is to bend the hooks on which the mesh is placed. After this, the pillars need to be painted. The upper ends of the Chainlink wire are twisted into one or two turns and bent down to avoid injury.

Sectional fence Chainlink

The fence consists of sequentially assembled frames of angle sections into which a chain-link mesh is mounted. Marking the fence and installing the posts yourself is done in the same way as with a tension fence. Columns are chosen that are stronger, since the load will be greater.

For the frame you need a steel corner 30*4 or 40*5 mm. The length of the fence section is 10 - 20 cm less than the distance between the posts, and the width is 10 - 15 cm less than the height of the post above the ground. Weld the corners into a rectangular frame of the required size.

If the length of the section is 2.0 m, then the width of the mesh will allow the roll to be unrolled vertically. A rod of 4 - 5 mm is threaded into the outer row and welded to the vertical corner of the section. Rods with a cross section of 4 - 5 mm are threaded into the upper and lower rows of the mesh, tensioned and welded to the horizontal corners of the frame. Do the same with the second vertical stand.

It remains to horizontally weld metal strips 50 x 5 mm and 15 - 30 cm long to the posts, retreating 20 - 30 cm from the top and bottom edges of the post. Weld the section between the posts to the strips. After graduation welding work the fence is being painted.

The video below describes the procedure for constructing a fence for a private house from Chainlink: www.youtube.com/watch?v=_YQ65Y2HvaM

How to make a fence from boards with your own hands

Wooden fences are traditionally popular in Russia. There are many types of wooden fences for a private house: hedge, wattle fence, picket fence, picket fence, etc. As an example, let's look at building the simplest thing with our own hands. wooden picket fence. It is better to use pine lumber: it is inexpensive, strong and durable.

The step-by-step construction of a fence looks like this:

1. Marking the territory.
2. The markup is no different from that described earlier.
3. Installation of supports. The holes for the pillars are made 50-80 cm deep in increments of 2.0 - 2.5 m. The supports can be beams 50 x 50 mm or 75 x 75 mm. They are installed strictly vertically, the holes are filled with soil, which is thoroughly compacted. It is better to concrete the pillars, having previously waterproofed the underground part.
4. Arrangement of crossbars. The crossbars are nailed horizontally to the support posts from above and below at a distance of 20-30 cm above the ground level and below the edge of the fence. The nails should come out reverse side 2-3 cm of support and be bent.
5. Picket fence device. Pre-prepared picket fence boards are nailed to the crossbars. You can nail it end-to-end if you need a solid fence or leave a gap of up to 5 cm between them. All nails on the back side should be carefully bent.

Painting a wooden fence

There are many materials for protecting wood. Imported impregnations are expensive, but provide good protection up to 50 years old. Drying oil remains the simplest and cheapest remedy. We carefully treat the constructed wooden fence with drying oil. After it dries, we paint it with wood paint. Sometimes it is suggested to install a visor on the top part fence The lower part of the fence should be well ventilated, so you need to constantly remove the grass, avoiding high humidity.

Video about building a wooden fence with your own hands: www.youtube.com/watch?v=TaZiTxrpCjU

conclusions

Construction of a fence with my own hands well within the capabilities of any homeowner. The technologies for producing the work are simple, but have several important features, which you need to pay special attention to:

1. The depth of the supports should be below the freezing level of the soil.
2. The underground part of wooden and metal supports must be covered with a layer of waterproofing to protect them from rotting or corrosion.
3. Work should begin with careful marking future design fencing.

Most cheap fence for a summer residence, one that is made from materials left over from construction, or simply lying idle. In this case, their initial cost is no longer important, and the labor costs will pay off in any case. For example, if there is a rocky outcrop in the vicinity, and after the construction of the house there is cement and sand left, then you can build the most expensive type of fence - from natural stone. Or the second option - a fence made from scraps of logs cut down on a tree plot

The fence of the site can be built like this in an unusual way Source 990.md

But these are more special cases - usually you have to buy materials or order a “turnkey fence”.

Features of a country fence

There are certain restrictions on the height and nature of the fence between adjacent areas. The fence should not cast a continuous shadow and be higher than 1.5 meters. Although in practice this is not always done. But it is precisely these requirements that make this part of the fence inexpensive in terms of materials. Everyone can build relatively accessible fence for the dacha, options for materials used for these purposes:

• Rabitz;
• wooden fence (picket fence);
• welded sections made of rolled metal.

For the part that protects country cottage area from the “street”, there is a greater choice of materials, including those listed above. But such a “transparent” fence has rather bad protective functions, especially from prying eyes, wind and dust. Therefore, such a fence for a dacha is used in combination with hedges - shrubs or climbing plants.

Translucent mesh fence climbing plants Source plodogorod.com

If a “blind” and cheap fence is needed along the front border of the site, then boards or corrugated sheets are chosen as materials. This way you can build a fence with your own hands cheaply and beautifully.

Wooden fences

You can build the cheapest fence out of wood. With the right choice and timely care, wooden fences will last at least 10 years. Moreover, this statement mainly applies to poles, and if they are made from a steel pipe with an anti-corrosion coating, then we can talk about at least twenty years of service. And, importantly, there is different types fences for dachas made of this material.

Usually fence, or fence board, is the simplest option wooden fence made from edged lumber. But the protective functions of the picket fence are low, as is its cost. A fence made of unedged boards only marks the boundary of the site, and its decorative qualities depend solely on the method of cutting the top of the slats and the color of the paint.

Although, if desired, a fence made from an ordinary picket fence can also be made attractive Source rozetka.com.ua

There are also “full-fledged” fences made of wooden picket fences, which are distinguished by higher reliability and degree of protection against penetration into the site. Moreover, such a fence can even be “deaf” if used double padding of fence boards– from the front and inside.

Blind fence made of slats Source yandex.com

Traditional type of decorative fence made of thin slats Source: seattlehelpers.org

A slatted fence also allows you to make decoration sections in the form of a decorative panel. And at first glance, a cheap fence will no longer look very cheap.

You can assemble this type of fencing, but this is clearly not a budget option Source vekzabora.ru

And they look very original "wicker" fences from wooden slats.

And this is what the modern interpretation of the fence looks like Source yandex.kz

Edged board fence can be either deaf or “holey”. In the first case, the boards on the veins are stuffed end-to-end or on both sides (alternately on the front and inside).

In the second case, the scheme for laying boards on the crossbars of the spans is similar to a picket fence. To some extent they are even similar, but this option is more “solid”.

A fence made from edged boards - reliability and solidity Source imagesait.ru

If horizontal direction wooden slats for a picket fence this is rare, but for an edged board this solution is more common. Perhaps this is the cheapest fence for a summer house, but it looks quite nice.

This covering of the span makes it look like the wall of a house Source navesi-vorota.kiev.ua

And you can put it in a separate category wooden fence shutters. This type of fence resembles a wall lined with plank. The principle of placing the board (or slats) is the same - at an angle to vertical plane with an overhang on the front side of the top panel over the bottom.

This type of fence appeared recently, but is already popular Source domvpavlino.ru

Fence blinds combine positive sides solid and “holey” spans:

• the territory is protected from prying eyes;
• direct exposure to wind and penetration of dust and dirt from the street are reduced;
• the area is ventilated, so excess moisture from the soil will evaporate more quickly;
• the shadow from the fence is not so “dense” and “short” plants can be planted nearby.

Video description

Example of fences made from other materials in the video:

Another type of wooden horizontal fence is fencing using a block house. This type of cladding panel is thick enough to withstand severe mechanical loads. A decorative properties panels fit perfectly into the rural landscape, especially if the house is built from rounded logs, lined with a block house or siding with a similar profile.

Block house, one of the most unusual finishing materials, looks great as a fence Source svoidomstroim.ru

Of course, this is not the cheapest fence - according to this characteristic, a block house does not lag behind most types of fencing made from planed lumber.

Budget fencing made from scrap materials

First of all, you need to understand that not all available materials can be “legal”. An example that can often be found as a cheap fence is a fence or picket fence made from branches or poles cut from a planting or nearby forest. Nowadays, fences made from pallets left over after construction are often chosen. In short, if you need an affordable fence for your dacha, there are many options.

Such a purely rustic fence can serve as a reason for administrative punishment Source jtcase.ru

But in this case, you can wait for the police to visit, since illegal cutting of trees and bushes (even vines) is punishable by both administrative and criminal codes. For individuals the fine is small - 4-5 thousand rubles. But this is if they find no signs of a criminal act. If found, the fine starts from 100 thousand rubles. Moreover, if such a fence is purchased, and its wood is obtained illegally, then the buyer will also face a fine.

And if purchasing a ready-made wicker fence can be considered an affordable option, then log palisade into the rank budget fence no longer hits.

A log palisade turns a home into a fortress, but it comes with a significant price tag. Source stroykauglich.ru

The most inexpensive material is slab. It belongs to lumber production waste, but this does not mean that any kind is suitable for a fence. It is divided into two classes: wood and business. And for the construction of a fence, you need to choose only the second option, as it is thicker and more uniform in cross-section geometry. Moreover, selection must be carried out both by the quality of the wood (lack of rot) and by the uniformity of size - it is advisable to select plates of approximately the same width and thickness. If there is a suspicion of infestation with a bark beetle, then the croaker must be sanded and treated with an appropriate solution so as not to infect the trees on the site.

Such a fence will be the cheapest among all, and it is quite appropriate in a rural landscape Source pinterest.ru

The second most expensive material is considered Not edged board . It makes affordable yet attractive wooden fences for your dacha. And here there are nuances of choice - it is better to use a wide format.

A vertical fence made from such a board is mounted overlapping, with the “front” and “wrong” sides alternating

And this site fence naturally looks rural areas Source: seattlehelpers.org

For horizontal fences, the arrangement of the plates is more varied. For example, it could be “volumetric” installation of boards around timber in the center of the span.

If you show your imagination, you can make an original fence for your site from an ordinary unedged board. Source music4good.ru

Attaching a herringbone board carried out by analogy with the installation of siding.

Another design of a blind fence made from unedged boards Source stroyholl.ru

There is one inexpensive option fencing materials – pallets. More precisely, Euro pallets. For their production, fairly high-quality edged boards are used, from which enterprising people even make furniture. And not only for the garden, but also for residential premises with an interior in a loft or rustic style.

The europallet can be used as a source of “raw materials”. That is, disassemble it into boards and make a regular vertical fence out of them. Or build a horizontal fence, borrowing not only boards from the pallet, but also the very idea of ​​a “two-row” volumetric structure.

Both the fence and the flowerbed Source www.sazhaemsad.ru

There are options when pallet practically unchanged goes into the manufacture of spans low fences.

This type of fence is perfect for a palisade in front of the house Source pinterest.es

Inexpensive metal fences

In this category, the cheapest garden fences are made from chain link mesh. Their apparent unreliability is deceptive - it is impossible to climb over them, and in order to gain unauthorized access to the site you must use at least metal scissors. When choosing what to make a fence from, you should not discard this option.

Chain-link mesh is the leader among metal fences for dachas Source ethanvizitei.com

This also includes fences with spans made of welded construction mesh , which is even stronger due to the greater thickness of the wire.

Fences from welded mesh- one of the easiest to make Source zabornik.ru

There are quite a lot of manufacturers of turnkey sectional fences using welded mesh as a basis. And in the most simple options it is not even attached to the frame from the corner. For fastening, special clamps are used, selected for the cross-section profile pipe, from which fence posts are made.

And this is the most affordable option metal sectional fence Source: seattlehelpers.org

And the next stage in the evolution of welded mesh as a material for fencing a site is gabions. IN landscape design wire baskets filled natural stone, usually used in the form retaining walls. They also found application for the construction of fences with “blind” spans. This design is more affordable than a stone fence, especially since the gabion does not need a foundation, and if necessary, it can be disassembled and moved to another place.

Gabion fence - a union of metal and stone Source ru.pinterest.com

Another inexpensive option is welded fences. from smooth reinforcement or square rod.

Welded fence made of smooth reinforcement - simple and elegant Source remex-tver.ru

And if you need to close the area from the street with a continuous fence with high resistance to burglary, then wall profiled sheet in the category not expensive materials there are no competitors.

Profiled sheet - reliability and safety of the site for little money Source zabory.dp.ua

Video description

And a few more options for beautiful fences in the video:

Conclusion

The final cost of the fence is influenced not only by the materials of the span, but also by its nature. Solid fences are strongly influenced by wind loads, so the supports for them must be more reliable than for through spans. And the calculation of their number and the size of the underground part has the same algorithm as that of a pile or monolithic foundation. Therefore, a cheap, but solid fence may ultimately cost more than its competitor made of more expensive materials that are freely blown by the wind.

It is very important that at the dacha the eye enjoys not only the plantings, but also the surrounding environment. About, and we have already talked about, it’s time to talk about how to make fences for your dacha with your own hands. Settlement without them dacha area is not possible and therefore it is better to take care of creating a strong and good fence. And it’s even better that it fits into the overall picture of what you create on your site.

DIY garden fences cheap

Don’t let the length of the fence or its height bother you. Let's start with the fact that it is easy to make a fence with your own hands and quite inexpensively, because if you have the desire and basic knowledge“fence theory”, then you can safely move on to the next stage - the choice of materials.

Country fencing can be made from:

• wood;
• picket fence;
• metal profiles;
• grids;
• yes everything, anything!

You just have to choose what you like best and fits into the overall design.

Wooden garden fence

Wood is one of the the best materials. It looks noble, can withstand bad weather, can be purchased without problems, and at the same time it is environmentally friendly.

It is not necessary to purchase a pre-prepared board. It is enough to get supplies and leftovers that have accumulated on backyard and are still suitable for use - ranch fences, for example, accept uncut and uneven boards. You only need to dig in wooden poles along the intended path and nail the boards to them in a horizontal position.

This is a fairly simple and cheap fence for a dacha, and if you take into account its environmental friendliness, then you should give preference to just such fencing.

In addition, depending on the length of the board, you choose its direction yourself, so you can build either a ranch fence or a simple vertical or horizontal fence, which has long proven itself.

To install a wooden fence with your own hands you will need:

• beam;
• boards;
• nails;
• hammer;
• shovel;
• sand.

If desired, you can add cement and bitumen to this list if you want the timber to be installed as stably as possible.

The principle of installing a wooden fence is very simple. You dig holes to install the support beam and fill them with cement or cover them tightly with sand, compacting it. This way the supports will not deform under the load of the boards and will become more stable.

Next, all you have to do is nail the boards to the posts. If you want to attach the boards vertically, then you will have to stretch and nail two planks between the supports, onto which the boards will then be attached. If you still want to see a ranch fence on your property, then it is enough to immediately attach the boards from post to post. More details in the video Ivan Galkin:

Just don’t forget that wood has its own shelf life and doesn’t like moisture. Therefore, be sure to paint the fence after construction and periodically inspect it for damage in order to repair or replace the board in time.

Picket fence

And picket fences are the most popular variety wooden fences. And no wonder, because the picket fence is so easy to install, economical to purchase and beautiful to look at finished form.

Before starting construction, it is necessary to mark the area where the building will be located, determine its height and the frequency of installing the picket fence. Although we install a fence for protection, if we tightly close the area, we can deprive the plants of light, which will lead to crop failure.

The set of materials for building a picket fence is similar to what we presented above:

• timber for supports;
• board for horizontal screed;
• cement;
• sand;
• nails or screws.

Tools can be different - from a shovel with a hammer to a screwdriver and an electric drill. Only the speed of construction will depend on this, but not the quality of the fence.

First you need to install the pillars, which will become the basis of the fence. Therefore, dig holes for the timber at an equal distance from each other, but no further than the length of the board that will serve as a screed. After this, install the supports and fill them cement mortar.

While the solution hardens (and this will take at least 3 days), you can proceed to the installation of sections. To do this, we cut the board to a length sufficient to attach its ends to the support. We place the sections on supports using nails or self-tapping screws and then attach a picket fence to them at an equal distance.

As you can see, the process of building a fence is quite simple and does not require any special construction skills - just patience to wait for the solution to harden. Then you can create a fence to your liking.

Well, to understand the intricacies of working with a picket fence and its installation, we recommend watching a video master class Andrey Krylov:

Metal profile fence

And yet, despite the beauty and cheapness of the picket fence and wood in general, it has one drawback - such a fence is short-lived and its maximum service life is only 15 years. Therefore, many, wanting to save money, are looking for a more durable, affordable and strong material- metal profile.

Due to its strength and availability, corrugated sheeting has long been wide application from summer residents. It is used for garden beds, roofing and, of course, fencing.

Metal profiles do not have the most aesthetic appearance, so most designers categorically bypass corrugated sheets when creating beautiful and original fences. But its accessibility and ease of use plays into the hands of summer residents, allowing them to good fence for a do-it-yourself dacha.

The construction of such a fence is not much different from others. You will need the same support posts and boards for the horizontal screed, on which the profile itself will be attached.

And since metal profiles are still not the most popular material for creating a fence, it’s worth dwelling a little on basic requirements for its installation:

1. The distance between supports should not exceed 2.5 meters. It’s better to stick to a more frequent, half-meter installation. This is due to the fact that the profiled sheet is quite flexible and will be deformed under the pressure of the wind, losing its beauty and, most importantly, strength. Therefore, the shorter the sections, the better the quality of the fence.
2. The supports must be buried at least 1.5 meters into the ground. Despite the flexibility of the metal profile, the sheet itself is quite heavy and requires stable support. That is why it is recommended to cement all supports at the base.
3. It is best to use not a beam as a post, but a pipe with a diameter of 6-8 cm and a wall thickness of at least 2 mm; such supports will definitely become a good basis for a stable and strong fence.
4. It is recommended to use 3 horizontal logs when installing the profile - top, bottom and middle. This way the fence will be more resistant to deformation and will better hold its shape under any pressure.

And so that you can be convinced of the simplicity of building such a fence, we invite you to watch the channel’s video master class We do it ourselves 36, where they share with us all the tricks of working with metal profiles:

Mesh fence for a summer residence

And yet one of the most budget options considered a chain-link fence. Like any metal product, the mesh tolerates most natural phenomena. And even rust can be prevented by timely treatment. Therefore, fences made from it are quite durable.

Fence mesh comes in several types:

1. Chainlink, which is sold in rolls, treated with polymers to prevent corrosion and can be easily installed between posts without unnecessary partitions,
2. Grooved, formed from wire with a cross-section of 6-7 mm and bent by a wave. It has a strong weave. And thanks to it, it keeps its shape well.
3. Welded, has a smaller wire cross-section than in the case of corrugated wire, but due to welding it is stronger. True, using it for a fence will be more expensive than in the case of chain-link.

A fence from any mesh can be made in two different ways:

1. Stretch the fabric around the perimeter and attach it to the support posts.
2. Stretch the mesh over the frame, and then assemble the fence from the resulting sections.

Allows you to keep track of your pets

Both methods have their own characteristics, so it is impossible to single out one of them as more profitable or simpler.

So, for example, by simply stretching the mesh from pillar to post, you will reduce the time for preparing materials. After all, you will only need to drive in the support, determine the height of the future fence and stretch the mesh, attaching it to the posts with wire.

This method is easy to implement and practical if you are short on time and want to make a temporary fence.

And yet it is worth considering that for a chain-link mesh, the posts will have to be placed at intervals of 1.5-2 meters, and this will increase the budget for the material. While for a corrugated mesh a distance of 3-4 meters is sufficient.

But if there are differences in height on your site, then this is the only solution if you have chosen mesh as the material. Sections are already prepared frames from metal profile, which brings us to the limitation - if you install them in a descending manner, there will be open space under the fence, which does not add either safety or aesthetic beauty to the site.

Installation of sections is simpler than stretching the mesh fabric. Ready-made frames are simply attached to the installed poles, equipped with the necessary anchors, or even welded to them.

As you can see, the choice of grid and method depends entirely on your desire to improve the area, the time you have and, of course, the budget allocated for this.

To figure out which material is right for you, you can take a look at a detailed master class on selecting materials and installing them in a fence.

If you want more clarity and understanding of how to do everything correctly, with explanations seasoned master, then it’s worth watching the video tutorial from the channel RemontHelp.com:

The grid itself consists of cells, i.e. your area will be clearly visible from the street. Therefore, it is usually recommended to use this material only between areas so as not to block the plantings from light.

Original ideas for a fence at the dacha from scrap materials

Every practical summer resident will consider it his duty to save as much as possible and use everything that remains from other projects. Therefore, before you start building a fence with your own hands, we suggest you think about whether it’s worth rushing to the store to buy a mesh or picket fence? Maybe we can make do with improvised materials?

Then let's see what we have accumulated over the entire time we owned the dacha? And is it possible to make decent fences out of this trash?

There is only one answer - yes, it is possible.

AND car tires, and , and the covers from them can become a fence or its decoration. Moreover, it will be no worse or more boring than one assembled from high-quality materials.

Tire fence

Let's start with tires, for example. A lot of this stuff always accumulates, so over time the question arises of where to put it. Recycling costs money, but the fence will also bring benefits. The choice is obvious.

Somewhat eclectic

All that remains is to fill the area well and begin to install the tires on top of each other in a checkerboard pattern, as if laying out bricks, or secure them to a previously installed chain-link fence.

By the way, if you build a fence from tires according to the pyramid principle, then the soil in the protruding parts can be used for flower beds, thus creating an entire green wall.

Fence made of plastic bottles

Plastic can be considered ideal material for the fence. After all, it decomposes in at least 60 years, which means that a fence made from it will not suffer from rain or sun. Although bottle plastic is still soft, and its shape at first glance is not suitable for building a fence, many began to give it a chance and use it for other purposes.

To enclose the entire summer cottage with such a “ plastic fence", you will need to accumulate a lot of bottles to create a complete fence.

The low weight of the material makes it easily deformed from physical damage. Moreover, if you have accumulated mainly transparent bottles, then such a fence will not provide protection from prying eyes. But the cost of the finished fence will be small.

If you combine bottles different color, then you can assemble entire mosaics. That's why creative personalities agree to endure shortcomings for the sake of an original fence that attracts the attention of passers-by.

To create a complete fence from plastic bottles It is recommended to take the same size of material. And it can already be assembled into a wall, stringing it on a wire like a curtain, or placing it on top of each other, filling the voids with cement mortar. The result will depend entirely on your desire to strengthen the fence or make it more airy.

By the way, bottle caps will also be used. After all, you can make a movable fence from them, and even with any pattern.

This will require a lot of caps with four drilled holes and meters of wire. Based on the colors you have, choose a pattern, and better diagram for embroidery with beads, and then simply string the lids in order, as in embroidery, in rows. Then pass the wire through vertical holes, thus connecting the rows.

If you are simply bored with the old fence, but still want to put the covers to use, then simply screw them on with self-tapping screws, creating a bright pattern-panel on the fence. And now you already have interesting wall on the site, attracting the attention of kids and pleasing your eyes.

A master class from Soloremont.

However, an ordinary picket fence or an old picket fence can simply be painted in an original way.

Fun pencils

You create your own mood and desire to visit the dacha more often!

Do-it-yourself wattle fence in the country: a master class for lovers of rural romance

And if you have ever seen a Ukrainian farm or met huts in the south of Russia, then your heart could not remain indifferent to this peaceful romance. And it’s not even these dear ones that sink into your soul, as if toy houses, with a thatched roof and whitewashed walls, and a wicker fence with clay hanging upside down on it.

And yet, in addition to the decorative component, the wattle fence is perfect solution even for modern dacha. Such a fence is not inferior in strength to either wood or metal. And in terms of beauty and attractiveness it will rank first among them.

And from the point of view of economy, it fits well into our criteria. After all, weaving such a fence will allow you to realize your creative side, and will also save your budget.

Flowers are clearly visible

But first, it’s worth preparing the material:

• timber or logs as a support and basis for weaving;
• material for weaving (preference is given to willow twigs, although twigs of other trees are also suitable, the main condition is their plasticity);
• gloves;
• shovel;
• sand.

If you are going to weave along already driven posts, then first dig them in and cover them with sand and compact them. After that you can start working on the rods themselves. It is necessary to steam the rods so that they become more flexible and do not break when deformed.

You can weave in different ways:

• horizontally, passing the rods in a figure eight between the pillars. This method was borrowed from weavers;
• vertically, between horizontally located logs. This weaving turns out to be more decorative than practical. That is why it is used for fences between adjacent areas, but not external ones;
• diagonally, forming an original wooden mesh. This type weaving is the most labor-intensive, because the rods must be long for the fence to be at least of medium height. In addition, it is recommended to dig each rod into the ground for greater stability.

To understand the intricacies simple weaving and try to make your first wattle fence, we recommend taking a look at the video tutorial Oleg Bryukhanov, where he shares the secrets of creating a simple but beautiful fence.

If you prefer sectional fencing, then the master class will be useful for you Yury Kulakevich, where he shows how to create a wicker wicker base.

As you can see, a fence is not easy protective structure, hiding the dacha plot from prying eyes, lovers of other people's harvests and stray dogs. A fence created with your own hands is also a decoration of the territory, allowing you to enjoy every day spent in nature, among the plants we planted with great love.