Home > Balcony and loggia > Metal scissors cricket attachment for drill. Types of drill attachments for cutting metal: their cost. Special attachment “Cricket” for a drill for cutting metal

Metal scissors cricket attachment for drill. Types of drill attachments for cutting metal: their cost. Special attachment “Cricket” for a drill for cutting metal

Thanks to large selection different drill attachments, this universal device can replace many other tools. So, for example, grinding discs eliminate the need to purchase grinding machine, and the attachment for tightening screws and self-tapping screws will replace the screwdriver.

Using such snap-ins, you can perform the following actions:

grinding;
polishing;
cutting;
mixing;
twisting;
drilling holes of different diameters;
milling.

At correct use the result will be of the same quality as if the work was performed using a special single-purpose tool. you can’t do without a drill with different attachments for a pigsty, cages for rabbits and others outbuildings at the dacha.

Types of nozzles

All drill attachments are divided according to purpose:

stops;
for drilling holes, crowns;
cutting, scissor attachments “Steel Beaver” and “Cricket”;
for drilling at an angle;
polishing and grinding;
cutters for wood and metal;
feather removal;
sharpening.

The parallel stop is used to adjust the drill depth; there are also special drill stands bottom reliable fastening tool. In addition to the standard drilling function, the drill can be used to make blind holes, for example, for installing hinges in wooden furniture. In this case, a Forstner drill is used. The base of the hole is flat and its edges are absolutely smooth. Or use feather drills instead.

Cutting attachments

Unlike an angle grinder, drill attachments for cutting metals work more delicately and do not deform the coating of the material being processed. The equipment is activated using the tool chuck on which it is installed.

For cutting metals, you should choose drill models with a speed of at least 2800 rpm.

Advantages of cutting attachments:

smooth cut;
comfortable work;
easy to use and maintain, no adjustment required.

The “Cricket” drill attachment is a nibbler with two cutting heads. They are used for cutting thin sheet metal: profiled metal sheets, metal tiles, profiled or sheet plastic, as well as polycarbonate. “Cricket” is simply irreplaceable when erecting on a site.

“Cricket” is used for sheets of materials with the following parameters:

the thickness of the sheet steel should not be more than 1.5 mm;
stainless steel up to 1.2 mm;
aluminum, copper and plastic no more than 2 mm.

The cut after processing this nozzle always remains smooth, without jagged edges, and the coating is intact.

To make a high-quality and even internal cut, you must first drill a hole.

The nozzle matrix rotates, thanks to which you can work with both horizontal and vertical surfaces. The recommended number of tool revolutions for using this equipment is 3000 rpm, minimum 1500 rpm.

Also for cutting profiled sheet metal and tiles, the “Steel Beaver” scissor attachment is used.

The principle of operation is similar to the previous nozzle; the cut occurs due to frequent back-and-forth movements of the punch, which bends the material and breaks it against the matrix. This equipment can be used to make curved and straight cuts. The minimum cutting radius is 1.2 cm. You can work with it at any angle (360°). Compared to the Cricket, the equipment is capable of cutting steel sheet greater thickness - 1.8 mm. The main advantage of the nozzle is an even cut, and due to the absence of sparks, it does not deform during operation. protective coating material.

Upon completion of work, you should carefully handle the sheet material, since the cut edge becomes sharp after processing.

Sanding and polishing attachments

Using drill attachments for grinding and polishing, you can the following types works:

metal polishing, wooden coverings, as well as glass surfaces;
grinding of metal, parts made of it and other materials;
removal of corrosion, scale, nicks and old coatings;
polishing the edge of the glass.

Compared to special tools These devices are inexpensive and can cope with a large number different tasks, I make any surface perfectly flat and smooth. In addition, they can be processed hard to reach places, where it is impossible to use other tools. But because of not large sizes It is difficult for them to complete a large amount of work.

When purchasing a drill attachment for processing wood or other material, you should carefully study the instructions. Since for different types rigging required different power and the number of tool revolutions.

All polishing and grinding attachments consist of a rod on which abrasive material, such as foam rubber, felt, brushes or sandpaper, is attached.

The following types are produced:

plate;
disk;
fan;
drums;
end;
cup-shaped

Polishing devices are divided not only by type of design, but also by degree of rigidity: hard, soft, super-soft, embossed.

Cup

A cup attachment for a drill for sanding wood or other coatings consists of a rod for fastening in a chuck, and a cup-shaped body filled with hard or light bristles. Most often it is used to remove corrosion or old coating. Models with a soft polishing part are also available: foam rubber, felt or other similar material. The body is made of durable and lightweight plastic or metal. Soft drill attachments are most often used for polishing a car.

Disc and plate

Disc devices, just like cup devices, consist of a rod, a body and a grinding material. The main difference from the previous model is the direction of the bristles (steel wire, brass brush), it is directed from the center to the edges of the disc. They must be used carefully, as they can quickly damage the coating.

Drill disc attachments for polishing or grinding are made on the same principle as for grinding devices. But instead of threads, they are equipped with a movable or fixed rod for fastening in the chuck. Sandpaper is attached to them using Velcro.

Experts recommend purchasing plate attachments with a movable rod, rubber or with a soft and thick layer between the Velcro and the base. Because then you can adjust the angle of the drill and smoothly follow the contours of the material.

When working with a rigid plate, it is more difficult to control, and even with a slight tilt it will create a noticeable depression in the surface. As a result, you can completely ruin the material. Therefore, it is recommended to use them only with the tool firmly secured to the stand.

Fan (petal), drum and end

Grinding fan attachments for drills are small disk in the center, to the edges of which petals of sandpaper or other abrasive material are attached. This device is convenient for processing hard-to-reach places, internal cavities or grinding holes, as it can take any shape. They are secured in the drill chuck in the same way as previous models, using a rod.

The drums are made in the form of a cylinder with a rod, covered on the outside with sandpaper. Unlike the disc attachment on a drill, the machining surface is located parallel to the chuck, and not perpendicular. They process wood, metal, and glass. Most often used for sharpening the end of glass. They are soft and hard depending on the purpose.

The end ones are a rod at the end of which the processing material is fixed in the form of a circle or cone. The attachments work on the principle of a file. Using them, you can increase the diameter of the hole, as well as remove jags and make the edges smooth.

Other attachments

The angle attachment on the drill allows you to make holes in places where it is impossible to work in normal mode. The angle can be adjusted or remain unchanged - 90°. Core bits are used for drilling in wood, concrete, ceramic and tiles, metal and other materials with large holes. They are made of high-quality steel so that the holes are smooth, without chips or cracks.

The attachment for sharpening drills is a body with a leash and whetstone inside. Holes for sharpening have different diameters. Their number can reach 15 pieces. Mixer attachments are used for mixing various solutions, paints and other mixtures. Selected depending on consistency. There is also a special attachment for tightening self-tapping screws or self-tapping screws, but it should be purchased for drills equipped with a speed reduction function.

For poultry owners, a feather removal attachment for a drill for plucking poultry has been developed. It instantly and safely removes all feathers from the carcass. In this case, the skin and meat are not damaged. Before work, there is no need to first scald the carcass or treat it after plucking with a blowtorch.

The drill attachment for plucking poultry is easy to use; you just need to securely secure the tool and bring the bird to it. Made from easy-to-clean materials and takes up very little space.

For those who work with wood material, different types of cutter attachments are available. They allow you to make grooves various forms, process holes or remove defects. They are pointed and backed.

Before working with any attachments, you should check the reliability of their fastening in the chuck and the material being processed. The drill must be held with both hands. During work, be sure to use protective equipment (gloves, goggles).

Homemade drill attachments - video

For repair and construction work It is necessary to periodically cut the metal. It is not always possible or advisable to purchase special expensive equipment. In such cases, a drill attachment for cutting metal can help out.

Special equipment for metal cutting

In production and construction, you need to regularly cut metal sheets, cut holes and cutouts of various shapes in them.

Many types of tools and equipment can cope with such tasks:

. She's Bulgarian. Using special cutting wheels, it is possible to cut sheet metal, fittings. It is often used precisely for these purposes. But there are disadvantages. Long cuts leave burrs, not suitable for corrugated sheets as they damage polymer coating, requires the constant purchase of trimming discs, which quickly wear out.
Guillotine. Performs cutting of rolled metal with a fairly wide range of thicknesses. Has high performance. They are mainly used only in enterprises due to the high cost of equipment.
Circular saw. It is possible to cut metal at different angles and with high precision. It is not possible to make complex cuts; after working with it, a lot of waste remains.
Jigsaw. Allows you to cut material at different angles. Suitable for cutting sheet metal.
Electric shears for metal. There are different types. For sheet steel - intended only for simple cutting of metal. Nibblers– in addition to straight and shaped cutting, makes a variety of holes. Slotted scissors - do an excellent job of cutting shapes and perform their task most accurately and accurately. The disadvantage of such tools is their rather high cost. Suitable for those who are professionally involved in construction and renovation. For one-time work and small volumes, purchasing electric scissors is impractical.
Drill attachments for cutting metal. There are two types - “cricket” and “steel beaver”. The operating principle is similar to electric cutting shears, but several times cheaper in cost.

Drill attachment “steel beaver”

There are undeniable advantages of using a drill for cutting rolled metal. Every craftsman has this tool - both a professional builder and a summer resident.

Drill – universal equipment thanks to the ability to change attachments. They can be for drilling holes, grinding, milling, sharpening, etc.

Design of drill attachments

Structurally, the “cricket” attachment is a punch with a matrix. The drill, by its rotation, imparts reciprocating movements to the punch. And two cutting heads carefully cut sheets of metal, punching them precisely.

In the treated surface, cuts a little more than three millimeters wide are obtained. Thanks to such small cuts, the edges of the material remain as smooth as possible, without burrs. Since the nozzle does not heat up during operation, the protective and polymer coating of the cut parts is not damaged.

"Cricket" is great for working with sheet metal, polycarbonate or other similar roofing materials, including metal tiles. With this attachment it is possible not only to smoothly process the edge, but also to make holes (for example, for a chimney), and make artistic cutouts. Based on the principle of operation, these are cutting shears.

The attachment can be used to cut sheet material with the following thickness parameters:

polycarbonate (plastic) up to 2 mm;
stainless steel up to 0.8 mm;
aluminum up to 2 mm;
zinc, iron, brass, galvanized steel up to 1.5 mm.

The attachment for cutting metal is screwed to a drill or screwdriver and clamped with the same nuts as the bits. The tool can be held at any angle, which makes working with it much easier. It also makes it possible to perform actions in any plane, which is indispensable for roof installation.

Metal cutting attachment

The nuances of using “cricket”

The choice of “cricket” is determined by a lot of advantages:

A neat cut. Unlike a grinder, the drill attachment will not leave burrs on metal surface and will not damage the polymer coating of the material with sparks.
Lightness of the tool. There is no need to put in a lot of force.
Compatible with drill and screwdriver. There is no need to purchase extra tools.
Price. Much cheaper than special equipment for cutting rolled metal, and also saves money on the purchase of consumables such as trimming discs for an angle grinder.
Easy to use. It is easy to install on the cartridge and also easy to remove.
Performance. Using a “cricket” you can cut material quite quickly.
Convenience. Thanks to its shape, it allows you to hold the tool at any angle.
Ability to cut holes and sections of any shape.
Versatility. Suitable not only for flat sheets metal, but also for profiled ones.

And yet, certain nuances of working with the nozzle exist. The tool must be held with both hands. That is, the material being cut must either be securely fastened, or the master must work with an assistant.

Like any instrument it requires skill. If you are using it for the first time, it is better to practice first. For efficient work attachment, the rotation speed of the drill should be 1500–3000 rpm. But when buying a “cricket”, you still need to clarify its characteristics and requirements - for some, the minimum rotation speed of the cartridge is 2700 rpm.

The “steel beaver” is similar in design and operating principle to the “cricket”. It also does a good job cutting sheet metal. Curvilinear cuts are made with a minimum radius of up to 12 mm. The difference is that the metal can be thicker - stainless steel up to 1.2 mm.

You also need to take into account that when working with these nozzles, a lot of metal shavings are formed.

Safety precautions

Regardless of the brand of drill and attachment, their price and characteristics, it is very important to follow safety precautions.

This will prevent injury and damage to the material.

When working with a drill, you need to wear safety glasses and gloves.
Before starting work, it is important to check the fastening of the nozzle.
Be sure to check whether the material to be cut is well secured.
The drill must be held with both hands using special holders.
When working with a metal cutting attachment, constantly remove falling chips. For example, when installing a roof, a large amount of chips can damage the surface of the metal tile.
After completing the work, do not touch the treated metal with your hands for some time and remove the attachments, as they may heat up due to friction.

So, when we cut metal sheets up to 2 mm thick, for example, when installing metal tiles or a fence made of corrugated sheets, and the amount of work is small or one-time, then it makes sense to turn your attention to drill attachments.

Video: Scissor attachment for cutting “Cricket”

When performing construction or repair work, it often becomes necessary to cut a metal workpiece. To do this, you should use special equipment in the form of a milling cutter, grinder or. However, it is not always at hand. You can cope with this task using a drill attachment for cutting metal, which will cut a product of small thickness.

Many craftsmen are accustomed to using a drill for its intended purpose, namely for drilling holes. But not everyone knows that this tool can be turned into a multifunctional device, complementing it with special attachments, accessories and stands, which will make the drill universal and indispensable in any job.

Using special drill attachments, which can be purchased at any specialized store. affordable price, you can drill holes of various diameters, cutting, grinding, polishing, twisting, mixing and milling. There are also pump attachments for drills designed for pumping liquid. The attachment for plucking chickens is simply irreplaceable in household. With the correct and competent use of additional attachments, the result will not be of worse quality, as when using a special single-purpose device, but the cost of such a universal tool will be several times lower.

According to their purpose, all existing nozzles are divided into:

equipment for drilling holes and crowns;
scissor attachments for cutting metal;
stops;
corner fixtures;
grinding and polishing attachments;
equipment for milling wood and metal;
sharpening devices;
feather nozzles.

When working with any drill attachment, you must follow the safety rules:

the equipment must be securely fastened in the tool chuck;
the drill must be held with both hands, which is especially important for powerful models;
constantly adjust the pressure of the tool;
work in personal protective equipment;
After completing the work, do not touch the drill for several minutes to avoid burns.

What are drill attachments for cutting metal?

Equipped with a special nozzle for cutting metal regular drill turns into a punch or cotter pin. The device pierces a metal product due to the implementation of numerous reciprocating movements along internal cavity matrices. As a result, an even cutting line with a width of 3.1 mm is formed while maintaining a protective layer on the surface of the metal sheet.

Important! Maximum efficiency of the nozzle is achieved only when working in conjunction with electric drill, the rotation speed of the chuck is at least 2700 rpm.

The metal drill attachment can cope with cutting the following metal products:

aluminum, up to 2 mm thick;
made of brass, copper, zinc, galvanized steel and sheet iron, up to 1.5 mm thick;
made from stainless steel, thickness up to 0.8 mm.

Using a drill attachment for cutting metal has a number of advantages:

the cut made is of high quality;
no need for constant acquisition consumables, which saves money;
provided high performance when cutting metal;
versatility of the device;
the equipment is convenient and easy to use and maintain;
the attachment can be used for electric and pneumatic drills;
Using the nozzle, you can make cuts of any configuration.

Despite all the above advantages, to get a cut high quality, the work requires some skills and dexterity.

Popular nozzle models

Today there are a large number various models drill attachments, thanks to which you can not only cut metal in a straight line, but also make curly cuts. This is necessary when installing ventilation air ducts, roofing structures, gutters. Using the attachment allows you to cut in any spatial position without making preliminary settings.

Types of nozzles:

cutting attachment " steel beaver» used for cutting metal tiles, corrugated sheets and any flat profile sheets;
universal attachment “Cricket” is used for cutting profile metal, polycarbonate and plastic;
special attachments for performing figured and curved cuts are represented by the EDMA Nibbek, ACRO YT-160 A, Sparky NP 1.8 L models, which differ in the thickness of the sheet being processed.

Scissor attachment for drill"Steel Beaver"

The classic drill attachment for cutting metal tiles and any flat sheets of metal in the form of a freely rotating shaft in a bearing with a fixed eccentric works on the principle of a crank mechanism with the difference that energy is supplied here for rotation.

A complete cutting tool has supporting part, located on the frame, and movable - connected to the eccentric. It is the moving part that makes reciprocating movements while the shaft rotates. Required element The design is a handle, which is fixed perpendicular to the axis of rotation of the spindle. When the load increases, torque occurs reactive torque, due to which the drill moves relative to the nozzle.

It should be remembered that the tool must be positioned strictly vertically relative to the workpiece when making a cut. Otherwise, product damage and operator injury may occur.

The device resembles metal scissors. Drill attachment used for cutting flat products or profile sheets with large radius bends. The cutting line is easy to control. When the tool is running protective layer the coating is not burned, which eliminates the formation of sparks and the possibility of burrs. You can perform continuous cutting of a product of any length. You can buy a drill attachment for cutting metal tiles and flat metal sheets for 1,600 rubles.

Using the “Steel Beaver” attachment for a drill, you can make a shaped cutout for installing roof ventilation elements or guttering

Sheet cutting is performed at a drill speed of 1500-3000 rpm. The cutting angle is 360 degrees, the minimum radius is 12 mm. Using the “Steel Beaver” attachment you can cut:

copper or aluminum sheet 2 mm thick;
steel - no more than 1.8 mm;
stainless steel - up to 1.2 mm,

Useful advice! To cut profiled sheets with small diameter bends, you should use “Cricket” type cutting shears.

Drill attachment “Cricket”

Nibblers “Cricket” got their name due to the characteristic noise during operation of the device. The nozzle is similar to previous model, however, it has a different design of the working element, consisting of two cutting heads. The operating principle of the Cricket attachment is similar to an office hole punch. During the oscillatory movements of the cylindrical striker at high frequency, neat holes are extruded into the metal. Thanks to forward movements along the marked line, it is possible to obtain an even cut.

The “Cricket” scissor attachment is used for cutting thin metal and profile sheets, and polymer thin-sheet products up to 2 mm thick. Work can be performed in the horizontal and vertical plane. Thanks to the ability of the tool to rotate 360 degrees. can drill large round holes and perform artistic cuts. You can buy a “Cricket” drill attachment for cutting metal for an average of 1,500-4,000 rubles.

The tool can cut metal with stiffeners and various profile stampings in two ways. The first option involves repeating the surface of the profile, going around the edges. Used for products with a medium bending radius. To cut metal tiles, another cutting option is used, according to which the tool moves along the stiffening ribs without bending around the sheet profile.

Before you buy an attachment for a Cricket drill, you should consider the main drawback of the tool. Due to the fact that the punch of the nozzle has a diameter of several millimeters, when cutting a product, a cut of a certain width is formed, which leads to certain material consumption. The result is metal shavings with sharp, crescent-shaped edges that should be disposed of immediately for safety reasons.

Useful advice! When working with the tool, do not wear soft shoes.

The Cricket drill attachment does not require adjustment and is easy to use and maintain.

One of the most popular models is the “Cricket” scissor attachment for metal up to 1.6 mm Enkor 14210. The tool is capable of cutting quite thick metal sheet in straight or curved direction. You can buy a drill attachment for cutting metal for 1,300 rubles. Main feature The advantage of the equipment is that during the cutting process a track with a width of only 1.6 mm is formed, which provides a fairly good level of material savings.

The device can be installed not only on a drill, but also on a screwdriver. The nozzle for cutting metal is lightweight, which does not increase the mass electrical appliance. The kit includes a replaceable handle, which increases the accuracy of work. The device has a low noise level due to its special design, which makes working with it more comfortable.

Drill attachment for sharpening drills

This device consists of a plastic body, inside of which a specially shaped sanding wheel rotates. It is this that allows you to form the required sharpening angle on the working part of the tool. The circle is mounted on a shaft, which is connected to the drill with a special coupling. It is activated when the tool is turned on.

Many modern models have an end cap on the body in which the holes are located various diameters For drill sharpening different sizes. These holes are made in such a way that the sharpening element comes into contact with the emery wheel in a certain position.

The principle of operation of the sharpening attachment is simple - when you turn on the drill, the chuck rotates the sharpening stone located inside

The drill sharpening process is performed as follows. The product is inserted with the cutting part into the hole of the nozzle of the appropriate diameter. After starting the drill, the emery wheel begins to rotate, sharpening half of the drill bit. Next, the product is turned over in the hole 180 degrees, and the procedure is repeated. This sequence of actions is performed several times until the required parameters of the cutting part of the drill are achieved.

The drill attachment for sharpening drills, which can be bought for an average of 350-500 rubles, has 15 holes with diameters from 3.5 to 10 mm. Products can be sharpened at an angle of 180 degrees due to the special shape of the stone. Simple design The device allows you to perform work quickly and without special skills.

Related article:

Types of structures, their characteristics and features. Review the best manufacturers machine tools Comparative characteristics of prices.

However, it should be remembered that the device is intended for sharpening worn-out cutting edges. To fully sharpen heavily worn products, an emery wheel will not be enough for a long time.

Useful advice! When purchasing an attachment of a certain model, you should take into account the diameter of the drill chuck.

There is also another type of additive. This is an attachment for a drill for sharpening knives and scissors, which is presented in the form of two sanding wheels mounted on the shaft and located at a certain distance from each other. The price of such a device is about 250 rubles.

The attachment for drill and scissors is easy to use and does not require special skills in its use.

Drill attachment for grinding

Using a grinding attachment on a drill, old coatings, corrosion, nicks, and scale are removed from the surface of the product. It is used to polish the edge of glass, metal parts and products made from other materials. Thanks to small size equipment can be used to process hard-to-reach areas. The average cost of a product is 500 rubles.

Drill attachments for grinding are used for preliminary rough preparation of the base for future polishing. It is made in the form of a rod on which grinding material in the form of a brush or sandpaper is fixed. There are various types of such devices that are used for specific tasks.

A cup attachment for a drill for grinding wood or other material is represented by a rod mounted on a chuck and a cup-shaped body filled with light or hard bristles. The body is made of metal or durable and lightweight plastic. Typically this attachment is used to remove old coating or corrosion from a surface.

Another variation is a disk attachment on a drill for grinding metal, where the bristles of the grinding material in the form of a brass brush or steel wire are directed towards the edges of the disk from its center. This additive should be used very carefully, as it can easily damage the coating. The plate nozzle has a movable or fixed rod, which is fixed to the cartridge. Sandpaper is attached to it using Velcro.

Useful advice! It is better to purchase attachments with a movable rod, which allows you to adjust the angle of the drill, while smoothly following the contours of the material.

A flap or fan sanding attachment is represented by a rod on which pieces of sandpaper or other abrasive material are attached. It is used for radius grinding or surface processing with a complex profile. It can also be used for grinding holes, like carbide cutters or cutters that work on the principle of a file.

Grinding abrasive stones, attached to the rod, are used to remove sagging, burrs, boring holes or leveling a weld.

Drill attachments for polishing

After sanding the base, it is necessary to give it smooth surface. This is done by polishing using special attachments. They can be made of felt, wool, foam rubber or felt. Depending on the degree of softness, they can be hard, soft, super soft and embossed. According to the method of fastening, there are nozzles with a rod, with Velcro, and with a holder-clamp. For polishing discs, fan or disk nozzles, end devices are used for holes. The average price of the product is 250-300 rubles.

Many car enthusiasts have in their arsenal a drill attachment for polishing a car. However, when choosing this product, you should consider some features:

the device must be of high quality and professional;
to carry out effective and safe polishing procedures, the maximum number of revolutions of the drill should not exceed 3000 rpm, as indicated in the characteristics of the device, otherwise the paint will simply burn;
the nozzle must be from a well-known brand;
the device should not be part of budget products;
for polishing each individual part car, you should use a special attachment designed specifically for this purpose.

The process of polishing a car using a drill is very complex and labor-intensive process requiring certain skills. If you have no experience, you first need to learn all the intricacies this process, master the basic techniques presented in videos on the Internet. It is better to start with inconspicuous areas of the body. The tool is adjusted to the desired parameters, taking into account the required number of revolutions. The nozzle should not be pressed too hard against the surface to high temperature do not burn the paint.

Drill attachment for plucking poultry

Plucking poultry is a very labor-intensive process, especially when it is necessary to process several carcasses. Therefore, many farmers were constantly looking for new solutions not only to make work easier, but also to reduce overall time. For this purpose, a feather removal attachment for the drill was specially developed, which removes feathers from the bird in a matter of minutes. It is similar to a dish brush, only the bristles here are silicone fingers, which, when the shaft rotates, pull feathers out of the carcass. The bird is presented on different sides.

An attachment for a drill for plucking poultry, which can be purchased for an average of 1,500 rubles. processes poultry carcasses in just 2-3 minutes, without leaving a single feather. The result is smooth, undamaged skin. The device is effective not only for processing chickens, but also gives good results when plucking geese. The drill attachment can be used not only for fresh, but also for frozen poultry.

Useful advice! Before using the attachment, it is not recommended to scald the carcass with boiling water, which will reduce the efficiency of the processing process.

The main advantages of a pen attachment for a drill, which can be purchased at any specialized store, are speed, simplicity and mobility of use, which does not require specific skills and additional processing carcasses before plucking. Significant disadvantage device is that after this mechanical process damage remains on the carcass, which deteriorates it appearance. Therefore, if the bird is intended for sale, it should be plucked manually.

Other types of nozzles

When it is not possible to make a hole in the usual way, you need to use an angle attachment for a drill. The working head of such a device can be rotated under different angles relative to the axis of rotation of the drill chuck. The main disadvantage of the equipment is the increased risk of drill failure. Therefore, it is considered the most popular angle attachment for a drill 90 degrees, which is fixed on the neck of the drill. The price of the product is on average 800 rubles.

For craftsmen who make furniture, cutter attachments are in great demand. various types. They can be backed and pointed. With their help, you can make grooves of different shapes and depths, process holes and remove defects. The cost of equipment is in the range of 350-450 rubles.

To mix solutions of different consistencies, use a mixer attachment for a drill, which is selected taking into account the density of the solution. So, for mixing glue, liquid putties and other fluid mixtures, spiral-shaped devices are used that prevent splashing of the solution. To mix concrete, nozzles with a hexagon-shaped tail are used. Mixing mixtures using this attachment will be done quickly and efficiently. However, in order not to reduce the efficiency of the device, the volume of the mixture for mixing should be maintained. The price of the nozzle is 500 rubles.

Useful advice! When choosing a mixer attachment for a drill, you need to consider the power of the tool. Increasing the load can lead to winding burnout.

An indispensable tool for concreting is a concrete vibrator attachment for a drill, the price of which is about 900 rubles. It is used to compact the concrete mass during its laying, namely, it is intended to remove bubbles and air layers from fresh concrete. The attachment requires a drill with a power of at least 1500 W.

For wood turning home handyman You just can’t do without a drill attachment for cutting wood, average price which is 2000 rubles. To pump liquid, you can use a pump attachment.

A wide selection of different attachments, attachments and accessories makes the drill universal tool, which is indispensable when performing repair work and for other household needs. It's simple and optimal solution, which will allow you to avoid purchasing expensive specialized power tools.

Using special drill attachments, which can be purchased at any specialized store at an affordable price, you can drill holes of various diameters, cutting, grinding, polishing, twisting, mixing and milling. There are also pump attachments for drills designed for pumping liquid. An attachment for plucking chickens is simply indispensable in the household. With the correct and competent use of additional attachments, the result will not be of worse quality, as when using a special single-purpose device, but the cost of such a universal tool will be several times lower.

According to their purpose, all existing nozzles are divided into:

equipment for drilling holes and crowns;
scissor attachments for cutting metal;
stops;
corner fixtures;
grinding and polishing attachments;
equipment for milling wood and metal;
sharpening devices;
feather nozzles.

When working with any drill attachment, you must follow the safety rules:

the equipment must be securely fastened in the tool chuck;
the drill must be held with both hands, which is especially important for powerful models;
constantly adjust the pressure of the tool;
work in personal protective equipment;
After completing the work, do not touch the drill for several minutes to avoid burns.

What are drill attachments for cutting metal?

Equipped with a special attachment for cutting metal, a regular drill turns into a punch or cotter pin. The device pierces a metal product due to numerous reciprocating movements along the internal cavity of the matrix. As a result, an even cutting line with a width of 3.1 mm is formed while maintaining a protective layer on the surface of the metal sheet.

Important! The maximum efficiency of the attachment is achieved only when working in conjunction with an electric drill, the rotation speed of which is at least 2700 rpm.

The metal drill attachment can cope with cutting the following metal products:

aluminum, up to 2 mm thick;
made of brass, copper, zinc, galvanized steel and sheet iron, up to 1.5 mm thick;
made of stainless steel, up to 0.8 mm thick.

Using a drill attachment for cutting metal has a number of advantages:

the cut made is of high quality;
there is no need to constantly purchase consumables, which saves money;
ensures high productivity when cutting metal;
versatility of the device;
the equipment is convenient and easy to use and maintain;
the attachment can be used for electric and pneumatic drills;
Using the nozzle, you can make cuts of any configuration.

Despite all the above advantages, in order to obtain a high-quality cut, some skills and dexterity are required for the work.

Popular nozzle models

Today, there are a large number of different models of drill attachments, thanks to which you can not only cut metal in a straight line, but also make shaped cuts. This is necessary when installing ventilation air ducts, roofing structures, and gutters. Using the attachment allows you to cut in any spatial position without making preliminary settings.

Types of nozzles:

the “Steel Beaver” cutting attachment is used for cutting metal tiles, corrugated sheets and any flat profile sheets;
The universal nozzle “Cricket” is used for cutting profile metal, polycarbonate and plastic;
special attachments for performing figured and curved cuts are represented by the EDMA Nibbek, ACRO YT-160 A, Sparky NP 1.8 L models, which differ in the thickness of the sheet being processed.

Scissor attachment for drill"Steel Beaver"

A full-fledged cutting tool has a support part located on the frame and a movable part connected to an eccentric. It is the moving part that makes reciprocating movements while the shaft rotates. A mandatory element of the design is the handle, which is fixed perpendicular to the axis of rotation of the spindle. When the load increases, a reactive torque occurs, due to which the drill moves relative to the nozzle.

It should be remembered that the tool must be positioned strictly vertically relative to the workpiece when making a cut. Otherwise, product damage and operator injury may occur.

The device resembles metal scissors. The drill attachment is used for cutting flat products or profile sheets with large radius bends. The cutting line is easy to control. During operation of the tool, the protective layer of the coating is not burned, which eliminates the formation of sparks and the possibility of burrs. You can perform continuous cutting of a product of any length. You can buy a drill attachment for cutting metal tiles and flat metal sheets for 1,600 rubles.

Using the “Steel Beaver” attachment for a drill, you can make a shaped cutout for installing roof ventilation elements or guttering

Sheet cutting is performed at a drill speed of 1500-3000 rpm. The cutting angle is 360 degrees, the minimum radius is 12 mm. Using the “Steel Beaver” attachment you can cut:

copper or aluminum sheet 2 mm thick;
steel - no more than 1.8 mm;
stainless steel - up to 1.2 mm,

Useful advice! To cut profiled sheets with small diameter bends, you should use “Cricket” type cutting shears.

Drill attachment “Cricket”

Nibblers “Cricket” got their name due to the characteristic noise during operation of the device. The nozzle is similar to the previous model, but has a different design of the working element, consisting of two cutting heads. The operating principle of the Cricket attachment is similar to an office hole punch. During the oscillatory movements of the cylindrical striker at high frequency, neat holes are extruded into the metal. Thanks to forward movements along the marked line, it is possible to obtain an even cut.

The “Cricket” scissor attachment is used for cutting thin metal and profile sheets, and polymer thin-sheet products up to 2 mm thick. Work can be performed in the horizontal and vertical plane. Thanks to the ability of the tool to rotate 360 degrees. You can drill large round holes and make artistic cuts. You can buy a “Cricket” drill attachment for cutting metal for an average of 1,500-4,000 rubles.

Useful advice! When working with the tool, do not wear soft shoes.

The Cricket drill attachment does not require adjustment and is easy to use and maintain.

One of the most popular models is the “Cricket” scissor attachment for metal up to 1.6 mm Enkor 14210. The tool is capable of cutting fairly thick metal sheets in a straight or curved direction. You can buy a drill attachment for cutting metal for 1,300 rubles. The main feature of the equipment is that during the cutting process a track with a width of only 1.6 mm is formed, which provides a fairly good level of material savings.

The device can be installed not only on a drill, but also on a screwdriver. The nozzle for cutting metal is lightweight, which does not increase the weight of the electrical device. The kit includes a replaceable handle, which increases the accuracy of work. The device has a low noise level due to its special design, which makes working with it more comfortable.

Drill attachment for sharpening drills

Many modern models have an end cap on the body, in which there are holes of different diameters for sharpening drills of different sizes. These holes are made in such a way that the sharpening element comes into contact with the emery wheel in a certain position.

The principle of operation of the sharpening attachment is simple - when you turn on the drill, the chuck rotates the sharpening stone located inside

The drill attachment for sharpening drills, which can be bought for an average of 350-500 rubles, has 15 holes with diameters from 3.5 to 10 mm. Products can be sharpened at an angle of 180 degrees due to the special shape of the stone. The simple design of the device allows you to perform work quickly and without special skills.

Related article:

Types of structures, their characteristics and features. Review of the best machine tool manufacturers. Comparative characteristics of prices.

However, it should be remembered that the device is intended for sharpening sagging cutting edges. To fully sharpen heavily worn products, an emery wheel will not be enough for a long time.

Useful advice! When purchasing an attachment of a certain model, you should take into account the diameter of the drill chuck.

The attachment for drill and scissors is easy to use and does not require special skills in its use.

Drill attachment for grinding

Using a grinding attachment on a drill, old coatings, corrosion, nicks, and scale are removed from the surface of the product. It is used for grinding the edges of glass, metal parts and products made from other materials. Thanks to the small size of the equipment, hard-to-reach areas can be processed. The average cost of a product is 500 rubles.

Useful advice! It is better to purchase attachments with a movable rod, which allows you to adjust the angle of the drill, while smoothly following the contours of the material.

Grinding abrasive stones mounted on a rod are used to remove sagging, burrs, boring holes or leveling a weld.

Drill attachments for polishing

After sanding the base, it is necessary to give it a smooth surface. This is done by polishing using special attachments. They can be made of felt, wool, foam rubber or felt. Depending on the degree of softness, they can be hard, soft, super soft and embossed. According to the method of fastening, there are nozzles with a rod, with Velcro, and with a locking holder. For polishing disks, fan or disk nozzles are used, and end devices are used for holes. The average price of the product is 250-300 rubles.

Many car enthusiasts have in their arsenal a drill attachment for polishing a car. However, when choosing this product, you should consider some features:

the device must be of high quality and professional;
to carry out effective and safe polishing procedures, the maximum number of revolutions of the drill should not exceed 3000 rpm, as indicated in the characteristics of the device, otherwise the paint will simply burn;
the nozzle must be from a well-known brand;
the device should not be part of budget products;
To polish each individual part of the car, you should use a special attachment designed specifically for this purpose.

The process of polishing a car using a drill is a very complex and time-consuming process that requires certain skills. If you have no experience, you first need to study all the intricacies of this process and master the basic techniques presented in videos on the Internet. It is better to start with inconspicuous areas of the body. The tool is adjusted to the desired parameters, taking into account the required number of revolutions. The nozzle should not be pressed too hard against the surface to avoid burning the paint with high temperature.

Drill attachment for plucking poultry

Useful advice! Before using the attachment, it is not recommended to scald the carcass with boiling water, which will reduce the efficiency of the processing process.

The main advantages of a feather-picking attachment for a drill, which can be purchased at any specialized store, are speed, simplicity and mobility of use, which does not require specific skills or additional processing of the carcass before plucking. A significant disadvantage of the device is that after this mechanical process, damage remains on the carcass, which worsens its appearance. Therefore, if the bird is intended for sale, it should be plucked manually.

Other types of nozzles

When it is not possible to make a hole in the usual way, you need to use an angle attachment for a drill. The working head of such a device can be rotated at different angles relative to the axis of rotation of the drill chuck. The main disadvantage of the equipment is the increased risk of drill failure. Therefore, the most popular is the 90-degree angle attachment for a drill, which is fixed on the neck of the drill. The price of the product is on average 800 rubles.

For craftsmen who make furniture, various types of cutter attachments are in great demand. They can be backed and pointed. With their help, you can make grooves of different shapes and depths, process holes and remove defects. The cost of equipment is in the range of 350-450 rubles.

Useful advice! When choosing a mixer attachment for a drill, you need to consider the power of the tool. Increasing the load can lead to winding burnout.

An indispensable tool for concreting is a concrete vibrator attachment for a drill, the price of which is about 900 rubles. It is used to compact the concrete mass during its laying, namely, it is intended to remove bubbles and air from fresh concrete. The attachment requires a drill with a power of at least 1500 W.

To perform wood turning work, a home craftsman simply cannot do without a drill attachment for cutting wood, the average price of which is 2,000 rubles. To pump liquid, you can use a pump attachment.

A wide selection of different attachments, attachments and accessories makes the drill a universal tool, which is indispensable when performing repair work and for other household needs. This is a simple and optimal solution that will allow you to avoid purchasing expensive specialized power tools.

Today, there are a great variety of all kinds of tools whose tasks include cutting and cutting thin sheet material. One way or another, they cope with their tasks, but they have one feature - universal scissors for metal does not exist. Some devices can easily be cut from flat sheet steel, others are great for stationary work, and others, being household tools, can barely cope with the task of cutting a plasterboard profile. The only exception is one device - cutting shears, one of the options of which is the “cricket” attachment for a drill, which will be discussed in this article.

Attachment for drill nibbler scissors “cricket” photo

How do cricket nibblers work?

Submit your work nibblers quite simple - in fact, it can be compared to a chisel that makes punctures in metal with high frequency. Another comparison would be the modern electric jigsaw, in which the standard file with teeth is replaced by a punching rod (chisel). This operating principle, combining a punching tool and a jigsaw, opens up wide possibilities and allows you to use a tool of this type even for shaped cutting of sheet iron. It is for this reason that modern builders use a “cricket” for cutting:

profiled flooring;
any smooth steel when it comes to large volumes of work.

These are not the only reasons why the drill attachment, cutting shears, has become widespread in the field of construction and repair.

Drill attachment “cricket” photo

Benefits of this tool

Another significant advantage of the cricket is its careful attitude towards protective and decorative coatings or metal tiles. Punching through the material, it not only does not injure it at the edges of the cut, but, on the contrary, rolls it, thus protecting the end of the cut from corrosion. As a result, the metal lasts much longer.

Additional benefits cutting metal drill attachments, the following points can be highlighted.

High productivity - a 1 m long cut can be completed in less than a minute. Yes, the grinder cuts faster, but unlike the nozzle, it burns the protective and decorative coating.
Just look at the ability to overcome almost any obstacle. Waves and various bends are not a problem at all - you can direct the movement of the cutter not only left and right, but also up and down.
According to the manufacturers, this tool can easily cope with metal up to 2 mm thick, which is quite enough for working with roofing materials.
The cost of the instrument can be called purely symbolic. It is at least five times lower than the price of professional cutting shears with built-in electric drive.

As for the disadvantages, there is only one most significant one - it is almost impossible to achieve a perfectly even cut. In principle, it is not needed, since the edges in most cases are overlapped either by another sheet of metal or special elements. If you try really hard and come up with some kind of guide, then this problem can be solved.

Safety precautions when working with a cricket

In addition to the risks of cutting yourself on the edges of sheet metal, there are a couple more points that you need to be careful of when working with a drill attachment. These are shavings - small and, most importantly, sharp fragments of metal in the shape of a crescent. They can cause very serious trouble.

First of all, the shavings easily penetrate into the legs, and you may not even feel it on rough feet. Then suppuration and all the ensuing consequences begin. It is best to work with the tool in closed shoes.
The second point is, or rather its impeller, which serves to cool the electric motor. Penetrating into the air intake hole, small metal crescents quickly damage the power tool. There is only one way to protect a drill - pack it in mesh material (for example, nylon tights).

In addition, we should not forget that small shavings scattered throughout the yard quickly corrode, and if they remain, for example, on paving slabs, then rust eats into it and spoils the appearance of the coating. Timely cleaning of the workplace solves almost all issues.

Drill attachment for cutting metal photo

What to look for when buying a cricket

Almost all instruments of this type have the same design and work on the same principle - no additional options they are not supplied, and no additional devices are provided for them. Everything is simple - including the choice, approaching which you need to pay attention to just a couple of points.

Basically, decide for yourself what is better for you - cheap and cheerful or expensive, but for a long time. From practice, I can only say one thing: my first Sparky nozzle worked in intensive use without repairs and maintenance within five years. By and large, we are not talking about such a lot of money - a professional attachment can be purchased for about 30-50 dollars.

To conclude the topic, the “cricket” drill attachment, there is only one thing left to add - to remind you that you can extend the life of any tool through proper care. Clean your “breadwinners” at the end of work and supervise them technical condition every self-respecting master should. Naturally, we should not forget about caring for the tool - hammering nails with an attachment and generally using it for other purposes is simply wrong.

Articles By topic:

Past tense (Präteritum) Along with Präteritum and Perfekt, it is included in the stage of past tenses. As a complex past tense, it consists of the auxiliary verbs haben or sein in the form Präteritum and the semantic verb in the form of the second participle (Partizip II). Choice of auxiliary verb	Lunar calendar of surgical operations Everyone who is about to undergo surgery carefully approaches the organization of this process: chooses a surgeon, discusses the nuances of the operation, possible complications and recovery time. It will also be important to choose the date for the operation.
The influence of the Moon on the fulfillment of desires The Full Moon is the highest point of the Moon's growth and an extremely powerful time. On this day, you can influence your destiny and change your life for the better if you know how to achieve harmony with lunar energy. The full moon has long been considered a mystical time: full	Are there insects in Antarctica In Antarctica, as you know, almost no snow falls - the winds carry the same snowflakes across the continent. Our elite is also almost never replenished; this is generally characteristic of stagnation, when vertical mobility is reduced to zero. In public policy - the same

Popular

2024-09-14 02:30:41	AI Warnings
2024-09-13 02:17:19	Characteristics of utterance levels as units of teaching speaking in a foreign language
2024-09-13 02:17:19	Center for Advanced Studies Advanced training, professional retraining
2024-09-12 02:14:28	Cis oleic acid. Oleic acid. Receipt and application. Production and chemical properties
2024-09-11 02:15:10	Artistic features of haiku matsuo basho as poetry of knowledge, spiritual transformation A father yearns for his child
2024-09-10 02:20:31	Why do you dream about a nest according to the dream book?
2024-09-10 02:20:31	Description and interpretation of the dream emerald
2024-09-09 02:12:10	Compatibility of a rooster and a pig in a relationship Compatibility of a rooster and a pig according to the horoscope
2024-09-07 02:24:25	Composition of Mezim: digestive enzymes in the treatment of stomach
2024-09-07 02:24:25	Regulation of enzyme activity and their methods Molecular mechanisms of regulation of enzyme activity

New

2024-08-23 02:06:21	Treatment of stalking mania: symptoms and signs Can stalking mania go away over time?
2024-08-20 02:06:20	Why did you dream about champagne?
2024-08-19 02:06:19	How to remove chin irritation in women and men Skin irritation on the chin
2024-08-18 02:06:06	Valentina Matvienko: biography, personal life, husband, children (photo)
2024-08-15 02:06:40	Piero della Francesca (Piero di Benedetto or Piero dal Borgo)
2024-08-15 02:06:40	Doctor Komarovsky’s opinion on DPT vaccination
2024-09-16 02:12:42	Past tense (Präteritum)
2024-09-15 02:17:34	Lunar calendar of surgical operations
2024-09-15 02:17:34	The influence of the Moon on the fulfillment of desires
2024-09-14 02:30:41	Are there insects in Antarctica
2024-09-14 02:30:41	AI Warnings
2024-09-13 02:17:19	Characteristics of utterance levels as units of teaching speaking in a foreign language