≡× MENU

• Interior
• Window
• Walls
• Projects
• The buildings

How to install horizontal blinds on a wall. How to hang blinds on plastic windows without drilling. Installation on plastic windows

Installing blinds on windows is not such a complicated process; you can do it yourself. There are different mounting methods for different types of curtains and each of them has its own installation nuances.

Mounting methods

There are three types of fastening blinds: to the wall, to the ceiling, directly to the frame, and two ways - with and without drilling. The universal basis of any fastening is the cornice, which different ways attaches to a wall, frame or ceiling.

With drilling

Fastening is carried out using self-tapping screws and brackets on which the cornice and fishing line are installed. Additionally, you will need a pencil, ruler, drill, and screwdriver.

First you need to make markings in the places where the brackets will be located. For reliability and accuracy, it is necessary to drill holes for the clamps in the marked places. Then, applying the brackets one by one to the PVC frame, use a screwdriver to secure them to the markings. Next, the cornice is installed and the entire structure is assembled.

No drilling

If you plan to replace the blinds or other window decoration options in the future, damage plastic windows Not recommended. Holes from self-tapping screws will remain in the frame forever and will significantly damage appearance windows In this case, it is easier to turn to a method that does not require drilling.

In this case, the brackets are attached in two ways:

• behind top part PVC profiles on opening sashes(you can simply hang it like a hook);
• on double-sided tape, which can be glued without fear of leaving marks.

Mounting blinds on the balcony requires a special approach. Important role The balcony design comes into play here. The type of glazing determines the possibility of choosing certain blinds and the method of their fastening.

In general, almost all options are available for balconies. Particular attention should be paid to the type of blinds, since not all of them are universal for different types of windows.

For example, for a balcony with sliding windows unsuitable horizontal blinds, since they can become deformed during use or from strong winds.

The nuances of installing different types of blinds

Horizontal

The light-protective design, which has become familiar and almost classic for window decoration, horizontal arrangement slats. Advantages:

• Compactness. Installed directly on the window, leaving the window sill free. This saves space and allows you to place greenery on the window in favorable conditions.
• Light weight structure.
• Strength and rigidity of the lamellas, preventing deformation.
• Fire safety.

• Simple control mechanism.
• Special coating or impregnation against dust, dirt, odors and grease.
• Resistance to humidity and temperature changes.
• Various materials for making lamellas: wood, plastic, aluminum, less often fabric.
• Easy installation.
• Affordable price.

Some disadvantages are worth mentioning:

• When mounted on a frame, the angle of inclination is limited window sashes when opening.
• The slats produce a characteristic knocking or ringing sound when the wind blows. To avoid this, you need to purchase lower fasteners, which are not included in the kit and quickly become unusable.
• The structure is subject to repair in case of severe deformation of several lamellas, but it will cost the same as new blinds.
• Not suitable for balconies and loggias with sliding windows.

Vertical

Blinds, as the name already implies, are a simple and convenient light-protective structure consisting of longitudinal vertical plates.

They are distinguished from horizontal ones by:

• More aesthetic appearance. Horizontal blinds are more likely to be functional, while vertical blinds are decorative.
• Possibility to cover large area one cornice. Horizontal blinds, as a rule, consist of narrow slats and are intended for minimalistic decor large windows. Vertical models have different widths and easily cover the area of ​​large windows, arches and doorways.
• Variety of materials. They can be made of wood fibers, wood, aluminum, bamboo, plastic, woven and non-woven fabric, mirror, blackout, thread. The abundance of materials provides another advantage - variability of colors and textures.
• Modern and original window design, opening up more design possibilities.

• Simplicity of control mechanisms. Both mechanical and electrical are possible.
• Possibility to place photo printing on curtains due to the larger surface and best characteristics material.
• Practicality. Larger slats are easier to wipe when necessary, which occurs infrequently. If, in the event of severe contamination, for example, in a children's room, the slats still need to be subjected to hygienic procedures, this will not take much time - they can be washed by hand and in a washing machine.
• Possibility of installation on non-standard windows(triangle, trapezoid, arch, bay window).
• The structure is subject to repair. To replace a particular part, you do not need to call a specialist; the repair is simple enough to do it yourself. You can replace the lamellas one at a time without dismantling the entire structure.

Rolled

Roller blinds and roller shutters are solid canvases, often made of textiles, but other materials are also possible that roll up like horizontal blinds.

The height can be adjusted by fixing the curtain with a weighting agent on the bottom strip of the canvas.

There are different types of roller shutters: with an open drum (for mounting directly on the window) and with a decorative cornice; “mini” for installation on each frame separately and “roll-cassette” for covering the entire window.

There is an opinion that roller blinds– this is the most budgetary and practical option window decoration, but this is not entirely true.

Of course, roller shutters have their advantages: a variety of natural and synthetic fabrics, colors and patterns, ease of care (allowed wet cleaning) and operation, the ability to fix the curtain at the desired height, special impregnations against dust, moisture, high temperatures and glare, compatibility with other types of curtains.

Roller blinds are convenient if you need to hide a room from the sun or decorate a window with beautiful tulle so that from the street you cannot see what is happening inside.

But with so many advantages, curtains also have significant disadvantages:

• The budget price is a misconception. Yes, a medium-sized curtain itself made from a common material will be inexpensive, but it will look boring. In order for the window design to be complete, it is necessary to consider additional decor, and this increases the cost several times.
• Roller blinds in the bedroom, office and rooms with high windows need electrical control. Electric drive designs are expensive, and some manufacturers also produce noise.

• It is impossible to make custom-made curtains from certain textiles. You can only choose specific products of a certain brand, since the range of fabrics for the production of roller blinds is very limited: translucent, textured, reflective, perforated, blackout.
• The maximum width of roller blinds is 280-300 cm, that is, to cover a large area with one cornice, for example, panoramic window or the balcony will not work.
• There may be problems with installation not on the wall, but in the window opening, since the bobbin is wider in width than the curtain itself. On the sides There will inevitably be gaps. Ceiling or wall mounting is preferable.

Pleated

This type of blinds is similar to both horizontal and roller blinds. The design consists of a control mechanism (chain or electric drive), weights, and pleated fabric that resembles accordion bellows. The range of materials, colors and textures is very diverse.

Peculiarities:

• They close from top to bottom, like classic canvases, from bottom to top, or from both sides at the same time. In this case, the degree of density of the “accordion” can be adjusted, thus closing either the upper, lower, or central part of the window.
• Suitable for curtains windows of irregular shape.
• Optimal solution for attic, attic, ceiling and inclined windows.
• “Opening”, the canvas compactly gathers into a fold and hides inside the cornice.

• Convenient for installation on all types of windows and double glazed windows.
• Various ways fastenings and control mechanisms (manual and electric).
• The woven fabric is washable.
• The curtain fabric can be made of two types of fabric at the same time, which makes it possible to regulate the degree of transparency, darkness, and sun protection.
• Easy installation you can do it yourself.

Kinds

• Classic. In appearance they are most similar to horizontal blinds, however, they can also be vertical. Made from fabric, paper or plastic. Designed for room darkening, protection from heating by sunlight, zoning internal space premises.

• Inclined. A type of pleated specifically for windows that are located at an angle in the attic or ceiling. Their peculiarity is in a specific assembly system, which does not allow the canvas of any material to sag when at an angle. Mostly inclined models are produced with electronic control.

• Corrugated. This type is a vertical and horizontal double pleat. As a result, the folds look smoother, neater and denser. Corrugation made of plastic and paper in this design absorbs a significant part of the heat and protects from bright light.

• Arched. The most flexible canvases that take any shape, like a paper fan. Good decision for rooms with non-standard form windows (arches, trapezoids, triangles, beveled windows).

• "Day Night". The fabric of such blinds consists of two layers of fabric: light, light-transmitting fabric for daytime use, and thick, dark fabric for protection from the bright sun during the day and prying eyes in the evening.

Cassette

Such systems involve either the use of horizontal slats or a solid fabric, but are not horizontal blinds or roller blinds.

They differ in the types of cassettes (angular, round, flat), controls (various types of mechanical and remote), and the materials used (plastic, textiles, bamboo, aluminum).

Their main feature is their design, the special structure of which makes it possible to fix the blinds at a minimum distance from the window glass. This prevents deformation, sagging, wrinkles and unevenness, and completely opens the window sill.

Advantages:

• Compactness. Cassette blinds take up minimal space, leaving owners the opportunity to use their imagination and organize additional window decoration or leave a window sill functional surface.
• Simple and clear type of control.
• Long service life. Special impregnation protects the canvas from dust, grease, dirt, moisture, and abrasion.
• Ease of hygiene procedures. Cassette systems do not require special care. It is enough to wipe their small surface area with a damp sponge and soapy water once every few months.

• A variety of designs for interiors in any style.
• The tight fit of the canvas to the surface of the glass protects equally well from heat and cold.
• Possibility to install the system yourself.
• A variety of materials - from light window decoration to total blackout protection.
• Possibility to combine blinds with curtains, tulle, lambrequin.

Measurements and tools

The final result depends on how correctly the measurements are taken. Even expensive, beautiful models will not look good on the window if there are gaps in the opening or the edges of the slats constantly ride up against the wall.

It is important to pay attention to the following points:

• For the most accurate indicators A steel tape measure and metal screws are used.
• The resulting numbers cannot be rounded., accuracy must be maintained down to millimeters.
• When ordering blinds The width parameter is indicated first, the length parameter – second.
• Not a single standard window opening has absolutely ideal geometric shapes, therefore measurements in height and width must be made at least at two points.

Horizontal

If you plan to attach blinds to the movable half of the window, you will need to measure the gap between the glazing beads and add at least 30 mm, which will prevent gaps from appearing in the structure. The height of the blinds is equal to the height of the window sash. For installation inside a window opening, measurements are required at three points in height and width, since openings are not always absolutely proportional.

The width is identical to the wide side of the glass plus the thickness of the rubber seal. The length is identical to the height of the window (including elastic bands) with a margin of 1 cm. To install the cornice, an additional 30-40 cm will be required to the slopes and hinges. The control chain is 2/3 of the window height. When choosing to fix the cornice on the wall, the width parameter increases by 10 cm, the height is measured from the point of attachment of the brackets to the floor at random.

Vertical

When installing in a window opening, you need to determine the width at the top of the arch and subtract 20 mm. To determine the height, compare the height of the left and right sides of the arch, subtract 1 cm from the smaller value. For wall mounting, you need to add at least 10 cm to the wide side of the slope. The length of the slats can be any, but it is recommended to retreat 2 cm from the edge of the blinds to the floor. Ceiling installation implies determining the height (to the floor or window sill) minus 2 cm, it is recommended to increase the width of the arch by 100+ mm.

Rolled

To install canvases to the wall, only one measurement is required - from the edge of the window sill to the markings for the brackets, and the width can be up to 300 cm. In the window arch, roller blinds are installed after measuring the width, from which you need to subtract 4 centimeters, and the length of the canvas is equal to the height of the window minus 15 mm.

Pleated curtains similarly do not require a professional approach to taking measurements and installation.

How to hang it on the wall yourself?

Installation work window design requires certain skills and experience, but if you want to try it yourself, you need to take into account some of the nuances and features of this work. Installation of blinds begins long before preparation work surface and a set of tools.

The first step of this process is an informed decision about the type and variety of blinds, material, color and texture, depending on the functionality of the room.

So, it is more advisable to choose vertical blinds for the living room that let in light, for the bedroom - automatic roller blinds with electric drive made of blackout fabric, and for the kitchen, where the smells of cooking and combustion products of food are constantly in the air - plastic blinds that do not absorb grease and dirt.

Second important point- this is the correct marking. A lot depends on it, including how easy the installation process will be.

If all the architectural features of window openings are taken into account by specialists when ordering blinds from them, everything will go easily and smoothly without the help of professional installers. It is also important to consider whether it will be possible to open the window after installation, how the light protection devices will work, and whether there is a risk of their deformation.

The installation of blinds must be carried out exactly with the markings and subsequent verification of the functionality of the structure. The most important point here is the choice between fastening - with or without drilling. It is also necessary to provide for the type of control.

For low windows, an excellent solution is one of the types of mechanical controls. Magnetic, automatic (electric) control with an electric drive is suitable for roof and inclined windows, windows in the bedroom.

Ceiling installation instructions

• First of all, you need to mount the blinds, assemble the brackets and install them on the reel. Then this structure must be fixed to the ceiling in order to mark for fastening.

• The second step is to attach the brackets with adhesive tape at the top of the frame and the string tensioner at the bottom. It is not necessary to pre-attach them with tape, but it is advisable to eliminate problems with subsequent drilling of holes for screws. After installing the guide string, the curtain itself is mounted into the mechanisms.

What is the best way to install automatic electric window blinds?

Automatic blinds are the most convenient way to decorate a window for independent execution.

They are attached in three ways: to the ceiling, to the frame with drilling, to the frame without drilling. In all cases, the fastener is a cornice with decorative facade or without it.

The brackets on which the structure is supported are fastened with self-tapping screws, hung or glued with double-sided tape.

The special tape, despite its apparent impracticality, is fixed very firmly, so it is important to correctly apply the markings for installing the brackets. Once they are glued, moving them will be very problematic.

Installation procedure:

• Preparing tools. You will need a stepladder, a set of screws from the kit, building level and drawing supplies, drill, screwdriver.
• Applying pencil markings for installing brackets. To securely fix the fasteners, it is recommended to drill holes for self-tapping screws at the same stage.
• Attaching the brackets in a suitable way(with or without drilling).
• Installation of cornice.
• Installation of slats. To do this, you need to pull the control cord on which the fastenings for the slats are located so that they are in the desired position. Then fix all the slats on the hooks of the fasteners.

How to attach cassette tapes yourself?

You can also install cassette blinds yourself. Before installation, you must read the instructions to make sure fully equipped, prepare everything necessary tools: screwdriver, drawing tools, screwdriver, drill, cotton pads or small piece of cloth, degreaser.

When everything you need has been collected, you can proceed to the first stage - degreasing the glazing beads. Then you need to remove the side covers of the box, lift it to the top of the frame, focusing on the guide protrusions, drill holes for fastenings, and secure with screws.

You can use a screwdriver for this purpose, or you can perform the process manually using a Phillips screwdriver.

Once the box is installed, you need to secure the covers to the sides. After this, you can glue the guide strips to the degreased frame. The guides should be several centimeters below the corner of the bead.

We hang aluminum curtains and blinds on sliding windows

For installation you will need a set of tools: wire, drill, Phillips screwdriver, screwdriver, drawing supplies.

The instructions for installing blinds on sliding windows contain a list of items that are carried out step by step:

• Draw marking line for installation of brackets. It must take into account the distance between the clamps and the control mechanism, between the brackets (from 60 cm) and to the extreme areas on the blinds (25 cm). For large blinds and significant weight, it is recommended to use intermediate fasteners.
• Drill holes for installing dowels on the surface to which you plan to attach the brackets. It is possible to use blinds on plastic windows without drilling.
• Installation profile.
• Fixing the top rod of the blinds on the brackets. It is important to remember that the blinds at this stage are already assembled.

Working with aluminum options on inclined surfaces requires a little more effort and skill.

How to secure the bottom?

The simplest and affordable way for DIY installation - this is a fastening without drilling based on double-sided adhesive tape. Suitable for tilt-and-turn mechanisms on windows.

Performed step by step:

• Degreasing of frame areas and fasteners, which will be connected with adhesive tape.
• Marking fastening roller shutters.
• Installation. The chain mechanism can be installed on any convenient side.
• Assembly brackets.
• Marking for fastening brackets. To do this, you need to install them on the assembled roller blind, install it on the window without fastening, mark with a pencil the places for the adhesive tape, and remove the curtain.
• Applying adhesive tape on the back surface of the brackets, mounting on a window.
• Installing the guide string against sagging. It is attached to the “ear” of the top bracket and the weighting of the curtain, and at the bottom it is fixed in the tensioner, which is installed on the frame.

This video shows how to hang horizontal blinds with your own hands.

To protect the premises from sunlight and prying eyes, we offer various solutions in the form of curtains, curtains, but in the interior modern room They fit in with difficulty and take up space. Another thing is the installation of blinds, which have long ceased to be an attribute exclusively office premises and moved into apartments. In addition, the market offers a wide variety of types and types of such products, which allows, by making them a decorative element, to solve all sorts of design problems. It will not be difficult to attach blinds to a plastic window with your own hands, and all work can be easily carried out without the involvement of specialists. The main thing is to decide on the choice of system, take the necessary measurements, and you can get down to business.

• Show all

  Types of installed structures

  Blinds are one of the types of curtains. Assembled from separate adjustable plates located parallel to each other, they perform several functions at once - they serve as window decoration, protect from light and regulate air flow. The types of products that are most widespread are discussed below.

  Horizontal. They are made up of thin plates arranged like a ladder. The slats are connected to each other by a cord, with which you can raise, lower and change their height. And to adjust the lighting intensity, a rotary rod is used. Curtains perfectly protect from bright daylight, are reliable, durable, easy to care for, inexpensive and practically free of drawbacks.

  Vertical. The slats in these blinds are located vertically in relation to each other. The rotation of the plates is carried out using a side mechanism driven by a decorative chain, and using ropes, they are moved to the sides, thereby opening the window.

  Such curtains are considered universal, since the curtain rod can be installed in a window opening, attached to the wall above it and to the ceiling. They are easy to install, undemanding to maintain, and perfectly regulate the intensity of incoming sunlight and air flow. But in order to open the window, they need to be moved to the side, and installed in the window opening, they do not allow flowers to be placed on the windowsill.

  

  Rolled. High functionality and attractive appearance make them a sought-after element. modern design apartments The design is simple - a roll of fabric is wound on a horizontal shaft, and control is carried out through a cord, a spring holder, and an electric drive. Fastening is carried out directly in the window opening, on the ceiling, wall, window sash.

  The curtains are impregnated with special compounds, so they are durable. They protect the room well from sunlight. The disadvantages are the high price and premature failure of the spring holder. Cassette roller blinds have been developed specifically for plastic windows. The difference is in the frame attached to the window sash, which saves space.

  

  Pleated. This is another type of curtain made of fabric gathered into a small fold. Control is carried out using a chain, cord, or electric drive. Most of all, they attract with their originality, good functionality, while being durable and reliable.

  

  Required measurements and installation location

  Before hanging the blinds, you need to decide on their installation location and take the correct measurements. Of all existing options fastenings - on window frame, wall, in the opening, the first is the most popular because it allows you to free up additional space. Regardless of the chosen model - horizontal, vertical, roller, the structure must overlap the window glass in height and width.

  

  If the sash is openable, then it is necessary to ensure its unhindered movement. A fastener is installed in the lower part to fix the lamellas relative to the glass unit. When the brackets are hung on the wall or attached to the ceiling, which is typical for vertical blinds, the width and height should be 20 and 5 cm larger than the size of the window opening, respectively.

  

  When attaching to the sash, measure the distance between the glazing beads and add one centimeter to each side. The height measurement is carried out in the same way, but on a blind sash, 3 cm is added to the result obtained, and on an openable sash, 4 cm is added.

  Possible mounting methods

  In the instructions supplied with their products, manufacturers indicate available options installation, but based on the current situation, you can choose one of the optimal schemes:

  • install with double-sided tape;
  • secure in the upper part of the frame using special brackets and clamps;
  • secure firmly with screws.

  

  The first two methods of attaching the structure to PVC windows are more suitable for lightweight fabric roller blinds, but despite a number of advantages, they also have disadvantages. So, over time, double-sided tape loses its original characteristics, this is especially evident when the window is located on the sunny side.

  Fastening in the upper part with clips increases the likelihood of damage to the sealing rubber and is only possible on opening sashes. Therefore, the most practical method is the drilling method, which allows you to reliably fix even heavy wooden and metal products with self-tapping screws. But the holes in plastic profile violate its tightness.

  Installation of horizontal type systems

  The sequence of work in this case will be as follows:

  • Unpack the blinds. Carefully study the instructions and check the contents, trying to understand how to assemble correctly.
  • Install the brackets on the top bar of the product and attach it to the frame. Taking a pencil, mark the attachment points. To prevent any distortion during the marking process, measure everything again with a level.
  • Using a thin drill, drill holes in the designated places; this approach will protect the plastic from cracking when screws are screwed into them. But it’s better to immediately take self-tapping screws with a drill at the end, their use will speed up the work.
  • Remove the brackets from the strip and secure them to the window profile.

  

  The fewer self-tapping screws are used, but without compromising the reliability of fastening, the lower the risk of breaking the tightness of the plastic structure.

  

  A container with slats is hung on the fixed brackets, which should be easily removed if necessary. After this, they check the correct installation by trying to open and close and raise and lower the blinds. If no problems arise, then lower holders are installed at the bottom of the window; the places of their attachment must be marked with the canvas stretched. Clamps are necessary to keep the slats from swinging when opening window sash, but if the window is blank and there are no drafts in the room, then they do not need to be installed.

  Features of fastening vertical structures

  Installation of curtains with vertical lamellas, which have left-side, right-side, central control, can be carried out in three ways:

  • into the window opening;
  • on the wall above the opening;
  • to the ceiling.

  Installation in a window opening. In this case, to obtain the required dimensions, measure the width of the opening itself directly at the installation site and subtract 1.5–2 cm from it. Do the same with the height. To make sure that the blinds will not interfere with the opening of the sash, additionally measure the distance from its top edge to the attachment point of the cornice. The resulting value must be no lower than 4.5 cm. Due to the possible curvature of the window opening, measurements of width and height must be carried out at three points.

  

  The further sequence of actions will be as follows:

  • mark the location of the fastenings;
  • drill holes for fasteners;
  • install fastenings;
  • hang the cornice by inserting it into special grooves;
  • secure strips of fabric and weights;
  • connect them with a lower chain.

  Installation above the window. In this case, when taking measurements, add 20 cm to the width of the opening on each side, and at least 10 cm to the upper slope. When carrying out the work, you will definitely need a drill, dowels, level, screwdriver or screwdriver.

  

  The sequence of operations is as follows:

  • when applying the cornice to the wall, determine and mark the attachment points, but if the length of the blinds is over two meters, additional fasteners are installed;
  • using a level, check the correctness of the markings;
  • the brackets are attached to the wall with screws;
  • hang clips;
  • secure the fabric and, after inserting weights, connect it with a lower chain.

  Ceiling mount. Vertical blinds can be attached using the method described above, the difference is that the necessary markings and fixation of the cornice are carried out directly on the ceiling. The distance to the window sill is made less by 2 cm from the actual one, and if to the floor, then by about 5 cm. If necessary, vertical curtains can be shortened. Then the weights are removed and, leaving a distance for stitching the material, they are cut off.

  

  The work is carried out in the following order:

  • Having attached the holders, mark the places of fastening;
  • drill holes for dowels;
  • brackets are attached with self-tapping screws;
  • insert the cornice into the clamps;
  • hang the slats and, having inserted weights, connect them with a lower chain.

  Installation of roller blinds

  Considering the light weight of such curtains, they can be attached to the window frame using double-sided tape or PVC staples. If the installation location is an opening or ceiling, then they are secured with self-tapping screws screwed into the dowel. In this case you will need additional tool in the form of a drill or hammer drill.

  

  When hanging blinds on a sash, in addition to the main dimensions, you need to know the depth of the glazing bead, which determines the choice of system. For values ​​up to 1.5 cm, Profil, Mini should be used, and if they exceed this figure, then Uni. The width of the curtain is determined by the width of the glass, adding 3 cm to it. Standard length about 2 meters, so in this regard they are suitable for most windows, but there should be about 50 cm of fabric left in the roll.

  

  To secure the blinds without resorting to drilling, you should:

  • Place a plug on the roll on one end, and a turning mechanism on the other;
  • insert the latch into the bracket and connect it to the bracket;
  • following the instructions, install the latter on the roll;

To save money, you can try to fix the blinds yourself. The work is not difficult, you just need to correctly mark the slope or frame, depending on where you need to secure the structure. You can use different ways to install such curtains; the choice is made based on the design features and dimensions.

Overview of types of curtains and blinds

For different objects, window design of a certain style and functionality is selected. The lamellas in the structure can be positioned in different ways: vertically, horizontally.

Horizontal blinds

You can find different types of shutters: pleated, interframe, attic, bamboo roller shutters; roller shutters belong to the same group. Main distinguishing feature– horizontal lamellas. They can have different thicknesses, widths and function differently. Such structures can be attached to a slope, a frame, they are also installed on top of a window block or inside the frame. It all depends on the size of the windows and the preferences of the homeowner.

Design of horizontal models

Classic horizontal blinds can be safely installed in premises with a variety of purposes: offices, private housing, industrial sites, administrative, retail and educational facilities. These are universal designs that are found in various shades.

Vertical blinds

Such curtains are usually attached over windows, which is due to the design features: vertically oriented slats, most often made of woven material. There are two main types similar designs: length to the floor or window sill.

General form and device vertical models

This is one of the reasons why such curtains are usually installed in private homes, apartments and offices. This type of blinds is installed using self-tapping screws. Exist Alternative option installations - to the ceiling surface.

Roller blinds

Window blinds in this design combine two types of curtains: classic fabric and horizontal plastic. They are equipped with a continuous sheet of different types of material, cover the double-glazed window, and, if necessary, rise by rolling into a roll.

Installation of roller blinds

Fastening of blinds of this type is carried out using self-tapping screws and brackets. You can hang them in various interiors.

Mounting options

Horizontal and vertical curtains are characterized by individual design features. Based on this, developed different methods fastenings:

Mount 1: On vertical structures

Vertical curtains can be mounted under the ceiling or over windows. Such blinds cannot be installed on plastic windows without drilling.

Mount 2: On a horizontal view

As standard, structures with horizontally oriented slats are attached directly to the window sashes, to the upper slope. Horizontal blinds without drilling can be placed in any design only on the sashes of the window block.

Mounting for vertical horizontal models to the wall

But the inter-frame analogue is created exclusively for installation in the space between window frames. There are also restrictions on installation to the upper slope; in particular, inter-frame and attic blinds are not attached this way. If you do the installation yourself, you must take into account design features products when choosing the installation method.

Preparation, taking measurements

The following tools will be useful: a screwdriver/screwdriver, a tape measure, a carpenter's pencil. In order for your curtains to function as efficiently as possible, you need to take the correct measurements. The structure should be located symmetrically relative to the glass unit.

If blinds are attached using adhesive tape without drilling, it is possible to correct errors. For analogues installed on brackets and screws, you need to mark as accurately as possible.

To fasten vertical curtains, it is enough to measure the dimensions of the window opening, the distance between the fastening points and the length to the bottom edge of the curtain. This will allow the structure to be correctly positioned relative to the level of the floor and window opening.

Horizontal blinds are often installed on the shutters, so the main measurements concern the double-glazed window: height, width of each glass. To these values ​​add 2 cm along the top and bottom edges, 0.5 cm on the sides.

Installation of vertical blinds

Anyone can install such curtains with their own hands. If the blinds are short, they can be placed inside the window openings. Otherwise, installation is carried out on the wall or under the ceiling.

For error-free fastening, sequential instructions are given:

Step 1: Marking

The central point of the window opening is determined and correlated with the center of the blind cornice. You need to make marks along the edges of the structure with your own hands. Points for installing self-tapping screws are marked on both sides of the cornice closer to the center of the window block by about 5-6 mm.

Place the cornice against the wall so that the center of the cornice coincides with the center of the window, and make marks along the edges.

Step 2: We look at the level

At the same time, you need to evaluate whether the slats are positioned correctly. Their lower part should be 1-2 cm above the floor level. The same amount must be retreated during installation short curtains(up to the windowsill).

Step 3: Attaching the brackets

Dowels are installed in holes prepared in advance with your own hands. The brackets are secured, this is done using self-tapping screws. Next, special clips are installed on these elements.

Be careful when using the hammer drill when drilling for bracket fastenings, otherwise part of the wall may break off.

Step 4: Installation of slats and chain

A cornice is attached, into which all that remains is to insert the runners and hang the vertical slats directly on them. Finishing touch– fastening the chain.

The slats must be hung in the exact order in which they are folded in the package. Otherwise, the design of the blinds may be damaged.

Installation of horizontal

Guided by the markings made earlier, you can attach the horizontal structure with your own hands. Instructions have been created for this:

1. First you need to secure the upper fasteners. To do this, use a screwdriver to prepare holes that will allow you to install the brackets using self-tapping screws.
2. Next, you need to hang the cornice; it is fastened until it clicks.
3. Holes for the lower fasteners (corners) are drilled taking into account the dimensions of the thread retainer connecting the lamellas. Typically, the design of blinds requires holes to be made on the sides of the glass. Then the latch, which is connected to the lamella sheet, can be easily inserted into the corners.

Do-it-yourself installation must be done with the utmost care, otherwise the blinds will not function correctly.

Methods for attaching roller blinds

When deciding how to install blinds on a window, the first priority is to determine the appropriate mounting method. The roll structure is mounted both on self-tapping screws and with the help of an adhesive (adhesive tape, liquid nails).

2 ways to attach roller curtains to pvc window, on L-shaped brackets and tape

In the first case, the technology for installing vertical curtains is taken as a basis, since roller blinds require fastening only in the upper part of the structure. To “plant” the structure on the adhesive, the surface of the windows is cleaned and degreased. This will improve the adhesion of materials.

This option is suitable for double frames. Installation of interframe plastic curtains- a complex process and requires the need to violate the integrity of the frame profile: holes (2 pieces) are drilled to output the blinds control system (handle and cord).

They should be located at the top of the inner sash. The brackets are installed on the upper profile, using the technology for installing horizontal blinds as a basis.

Basic tips for choosing:

• Before purchasing a design, you need to clarify the composition of the kit, in particular, the presence of fasteners;
• If the installation is easy to do yourself, then it is better to entrust the repair of curtains to a specialist;
• Plastic is easier to care for;
• It is not recommended to clean the new structure too often, as this will quickly wear off the protective coating.

For example, horizontal blinds can be positioned inside in any convenient way. However, the most popular option is on top of the sash. The inter-frame structure is more difficult to install, and the vertical analogue can only be located above the window or under the ceiling due to its large dimensions.

Installing blinds solves many problems with window decoration. Curtains, drapes, tulles, no matter what fabric they are made from, require frequent washing, since dust and dirt accumulate on them. The thickness of the curtains determines how well they transmit or block light.

Blinds are much more convenient than curtains in many aspects.

Depending on the angle at which the lamellas are located, they completely open access to natural light into the room, partially block it, gently diffuse it, or completely isolate the room not only from light, but also from thermal radiation. They do not require special care, and installing blinds yourself is not difficult.

Varieties

Horizontal

The light-protective design with horizontal lamellas has become familiar, almost classic for window design.

Advantages:

• Compactness. Installed directly on the window, leaving the window sill free. This saves space and allows you to place greenery on the window in favorable conditions;
• Low weight of the structure;
• Strength and rigidity of the lamellas, preventing deformation;
• Fire safety;
• Simple control mechanism;
• Special coating or impregnation against dust, dirt, odors and grease;
• Resistance to humidity and temperature changes;
• Various materials for making lamellas: wood, plastic, aluminum, less often fabrics;
• Easy installation;
• Affordable price.

Some disadvantages are worth mentioning:

• When mounted on a frame, the angle of inclination of window sashes when opening is limited;
• The slats produce a characteristic knocking or ringing sound when the wind blows. To avoid this, you need to purchase lower fasteners, which are not included in the kit and quickly become unusable;
• The structure is subject to repair if several slats are severely deformed, but it will cost the same as new blinds;
• Not suitable for balconies and loggias with sliding windows.

Vertical

They are distinguished from horizontal ones by:

• More aesthetic appearance. Horizontal blinds are more likely to be functional, while vertical blinds are decorative;
• Possibility to cover a large area with one cornice. Horizontal blinds, as a rule, consist of narrow slats and are designed for minimalistic decoration of small windows. Vertical models have different widths and easily cover the area of ​​​​large windows, arches and doorways.
• Variety of materials. They can be made of wood fibers, wood, aluminum, bamboo, plastic, woven and non-woven fabric, mirror, blackout, thread. The abundance of materials provides another advantage - variability of colors and textures;
• Modern and original window design, opening up more design possibilities;
• Simplicity of control mechanisms. Both mechanical and electrical are possible;
• The ability to place photo printing on “curtains” due to the larger surface and better characteristics of the material;
• Practicality. Larger slats are easier to wipe when necessary, which does not arise often. If, in the event of severe contamination, for example, in a children's room, the slats still need to be subjected to hygienic procedures, it will not take much time - they can be washed by hand and in a washing machine;
• Possibility of installation on non-standard windows (triangle, trapezoid, arch, bay window);
• The structure is subject to repair. To replace this or that part, you do not need to call a specialist; it is simple enough to do it yourself. You can replace the slats one at a time without having to dismantle the entire structure.

Vertical blinds, as is clear from the name, are a simple and convenient light-protective structure consisting of longitudinal vertical plates.

Rolled

Roller blinds and roller shutters are solid canvases, usually made of textiles, but other materials are also possible, which, like horizontal blinds, are rolled up. The height can be adjusted by fixing the curtain with a weighting agent on the bottom strip of the canvas.

There are different types of roller shutters: with an open drum (for mounting directly on the window) and with a decorative cornice; “mini” for installation on each frame separately and “roll-cassette” for covering the entire window.

There is an opinion that roller blinds are the most budget-friendly and practical option for window design, but this is not entirely true. Of course Roller shutters have their advantages: a variety of natural and synthetic fabrics, colors and patterns, ease of care (wet cleaning is allowed) and operation, the ability to fix the curtain at the desired height, special impregnations against dust, moisture, high temperatures and glare, compatibility with other types of curtains. It is convenient if you need to hide a room from the sun, or decorate a window with beautiful tulle so that from the street you cannot see what is happening inside.

But with so many advantages, they also have significant disadvantages.:

• Budget price- it's a delusion. Yes, a medium-sized curtain itself made from a common material will be inexpensive, but it will look boring. In order for the window design to be complete, it is necessary to think through additional decor, and this increases the cost several times;
• Roller blinds in the bedroom, office and rooms with high windows need electrical control. Electric drive designs are expensive, and some manufacturers also produce noise;
• Impossible make a custom curtain from a specific textile. You can only choose specific products of a specific brand, since the range of fabrics for the production of roller blinds is very limited: translucent, textured, reflective, perforated, blackout and that’s all, perhaps;
• Maximum width roller blinds - 280-300cm, that is, covering a large area with one cornice, for example, a panoramic window or balcony;
• They can There will be problems with installation not on the wall, but in the window opening, since the bobbin is wider in width than the curtain itself. There will inevitably be gaps on the sides of the window openings. Ceiling or wall mounting is preferable.

Pleated

This type of blinds is similar to both horizontal and roller blinds. The design consists of a control mechanism (chain or electric drive), weights, and pleated fabric that resembles accordion bellows.

The range of materials, colors and textures is very diverse.

Peculiarities:

• They close from top to bottom, like classic canvases, from bottom to top, or from both sides at the same time. In this case, the degree of density of the “accordion” can be adjusted, thus closing either the upper, lower, or central part of the window;
• Suitable for covering irregularly shaped windows;
• The optimal solution for dormer, attic, ceiling and inclined windows;
• “Opening”, the canvas is compactly folded and hidden inside the cornice;
• Convenient for installation on all types of windows;
• Various methods of fastening and control mechanisms (manual and electric);
• The woven fabric is washable;
• The curtain fabric can be made of two types of fabric at the same time, which makes it possible to regulate the degree of transparency, darkness, and sun protection;
• Easy installation can be done by yourself.

Types of pleated:

• Classic. In appearance they are most similar to horizontal blinds, but they can also be vertical. Made from fabric, paper or plastic. Designed to darken the room, protect against heating by the sun's rays, and zone the interior space of the room.

• Corrugated. This type is a vertical and horizontal double pleat. As a result, the folds look smoother, neater and denser. Corrugation made of plastic and paper in this design absorbs a significant part of the heat and protects from bright light.

• Inclined. A type of pleated specifically for windows that are located at an angle in the attic or ceiling. Their peculiarity is in a specific assembly system, which does not allow the canvas of any material to sag when at an angle. Mostly inclined models are produced with electronic control.

• Arched. The most flexible canvases that take any shape, like a paper fan. A good solution for rooms with non-standard window shapes (arches, trapezoids, triangles, sloping windows).

• "Day Night". The fabric of such blinds consists of two layers of fabric: light, light-transmitting fabric for daytime use, and thick, dark fabric for protection from the bright sun during the day and prying eyes in the evening.

Cassette

Such systems involve either the use of horizontal slats or a solid fabric, but are not horizontal blinds or roller blinds. They differ in the types of cassettes (angular, round, flat), controls (various types of mechanical and remote), and the materials used (plastic, textiles, bamboo, aluminum).

Their main feature is their design, the special structure of which makes it possible to fix the blinds at a minimum distance from the window glass. This prevents deformation, sagging, wrinkles and unevenness, and completely opens the window sill.

Advantages:

• Compactness. Cassette blinds take up a minimum of space, leaving owners the opportunity to use their imagination and organize additional window decoration or leave the window sill as a functional surface;
• Simple and clear type of control;
• Long service life. Special impregnation protects the canvas from dust, grease, dirt, moisture, abrasion;
• Ease of hygiene procedures. Cassette systems do not require special care. It is enough to wipe their small surface area with a damp sponge and soapy water once every few months;
• Variety of designs for interiors in any style;
• The tight fit of the canvas to the surface of the glass protects equally well from heat and cold;
• Possibility to install the system yourself;
• A variety of materials - from light window decoration to total blackout protection;
• Possibility to combine blinds with curtains, tulle, lambrequin.

Mounting methods

There are three types of fastening blinds: to the wall, to the ceiling, directly to the frame, and two ways - with and without drilling.

The universal basis of any fastening is the cornice, which is attached to the wall, frame or ceiling in different ways.

With drilling

This is done using self-tapping screws, brackets on which the cornice and fishing line are installed. Additionally, you will need a pencil, ruler, drill, and screwdriver.

First you need to make markings in the places where the brackets will be located.

For reliability and accuracy, it is necessary to drill holes for the clamps in the marked places. Then, applying the brackets one by one to the PVC frame, use a screwdriver to secure them to the markings. Next, the cornice is installed and the entire structure is assembled.

No drilling

If you plan to replace blinds or other window decoration options in the future, it is not recommended to damage plastic windows. The holes from the screws will remain in the frame forever and will significantly spoil the appearance of the windows. In this case, it is easier to turn to a method that does not require drilling.

In this case, the brackets are attached in two ways:

• by the upper part of the PVC profile on the opening doors (you can simply hang it like a hook);
• on double-sided tape, which can be glued without fear of leaving marks.

Mounting blinds on the balcony requires a special approach. The balcony design plays an important role here. The type of glazing determines the possibility of choosing certain blinds and the method of their fastening. In general, almost all options are available for balconies. Particular attention should be paid to the type of blinds, since not all of them are universal for different types of windows. For example, horizontal blinds are not suitable for a balcony with sliding windows, as they can become deformed during use or from strong winds.

Measurements and markings

The final result depends on how correctly the measurements are taken.

Even expensive, beautiful models will not look good on the window if there are gaps in the opening or the edges of the slats constantly ride up against the wall.

It is important to pay attention to the following points:

• For the most accurate indicators, a steel tape measure is used;
• The obtained figures cannot be rounded; accuracy must be maintained to the nearest millimeter;
• When ordering blinds, the width parameter is indicated first, length – second;
• Not a single window opening has absolutely ideal geometric shapes, so measurements in height and width must be made at least at two points.

Horizontal

If you plan to attach blinds to the movable half of the window, you will need to measure the gap between the glazing beads and add 30 mm or more, which will prevent gaps from appearing in the structure. The height of the blinds is equal to the height of the window sash.

For installation inside a window opening, measurements are required at three points in height and width, since openings are not always absolutely proportional.

The width is identical to the wide side of the glass plus the thickness of the rubber seal. The length is identical to the height of the window (including elastic bands) and has a margin of 1cm. To install the cornice, you will need an additional 30-40 cm to the slopes and hinges. The control chain is 2/3 of the window height.

When choosing to fix the cornice on the wall, the width parameter increases by 10 cm, the height is measured from the point of attachment of the brackets to the floor at random.

Vertical

When installing in a window opening, you need to determine the width at the top of the arch and subtract 20 mm. To determine the height, compare the height of the left and right sides of the arch, subtract 1 cm from the smaller value.

For wall mounting, you need to add at least 10 cm to the wide side of the slope. The length of the slats can be any, but it is recommended to retreat 2 cm from the edge of the blinds to the floor.

Ceiling installation involves determining the height (to the floor or window sill) minus 2 cm, it is recommended to increase the width of the arch by 100+ mm.

Rolled

To install canvases to the wall, only one measurement is required - from the edge of the window sill to the markings for the brackets, and the width can be up to 300 cm.

In the window arch, roller blinds are installed after measuring the width, from which you need to subtract 4 centimeters, and the length of the curtain is equal to the height of the window minus 15 mm.

Pleated curtains similarly do not require a professional approach to taking measurements and installation.

Installation of vertical models

Vertical blinds are the most convenient way to decorate a window yourself. They are attached in three ways: to the ceiling, to the frame with drilling, to the frame without drilling.

In all cases, the fastener is a cornice with or without a decorative facade.

The brackets on which the structure is supported are fastened with self-tapping screws, hung or glued with double-sided tape. The special tape, despite its apparent impracticality, is fixed very firmly, so it is important to correctly apply the markings for installing the brackets. Once they are glued, moving them will be very problematic.

The procedure for installing vertical blinds:

1. Preparing tools. You will need a stepladder, a set of self-tapping screws from the kit, a building level and drawing supplies, a drill, and a screwdriver.
2. Applying pencil markings for installing brackets. To securely fix the fasteners, it is recommended to drill holes for self-tapping screws at the same stage.
3. Fastening the brackets in a suitable way (with or without drilling).
4. Installation of cornice.
5. Installation of slats. To do this, you need to pull the control cord on which the fastenings for the slats are located so that they are in the desired position. Then fix all the slats on the hooks of the fasteners.

Installation of horizontal

For installation you will need a set of tools: drill, Phillips screwdriver, screwdriver, drawing supplies.

The instructions for installing horizontal blinds on windows contain a list of items that are carried out step by step:

1. Draw a marking line for installing brackets. It must take into account the distance between the clamps and the control mechanism, between the brackets (from 60 cm) and to the extreme areas on the blinds (25 cm). For large blind widths and significant weight, it is recommended to use intermediate fasteners.
2. Drill holes for installing dowels on the surface to which you plan to attach the brackets. It is possible to use blinds on plastic windows without drilling.
3. Profile installation.
4. Fixing the top rod of the blinds on the brackets. It is important to remember that the blinds at this stage are already assembled.

Working with horizontal models on inclined surfaces requires a little more effort and skill.

How to hang roller blinds?

Like other types, roller blinds or shutters are attached in several ways: they can be hung, glued, or attached to a frame.

First way– the simplest and most accessible for do-it-yourself installation is a fastening without drilling based on double-sided adhesive tape. Suitable for tilt-and-turn mechanisms on windows. Performed step by step:

1. Degreasing the areas of the frame and fasteners that will be connected with adhesive tape.
2. Marking the fastening of roller shutters.
3. Installation of roller blinds. The chain mechanism can be installed on any convenient side.
4. Assembling brackets.
5. Marking for fastening brackets. To do this, you need to install them on the assembled roller blind, install it on the window without fastening, mark with a pencil the places for the adhesive tape, and remove the curtain.
6. Applying adhesive tape to the back surface of the brackets, mounting on a window.
7. Installing the guide string against sagging. It is attached to the “ear” of the top bracket and the weighting of the curtain, and at the bottom it is fixed in the tensioner, which is installed on the frame.

The second method involves attaching to a stationary frame (not opening):

• First of all you need to mount the roller blind, assemble the brackets and install them on the reel. Then this structure must be fixed on the window in order to mark for fastening.
• Second step– fastening the brackets with adhesive tape in the upper part of the frame and the string tensioner in the lower part. It is not necessary to pre-attach them with tape, but it is advisable to eliminate problems with subsequent drilling of holes for screws. After installing the guide string, the curtain itself is mounted into the mechanisms.

How to secure cassette tapes?

You can also install cassette blinds yourself. Before installation, you must read the instructions, make sure that everything is complete, and prepare all the necessary tools: a screwdriver, drawing tools, a screwdriver, a drill, cotton pads or a small piece of cloth, and a degreaser.

When everything you need has been collected, you can proceed to the first stage - degreasing the glazing beads. Then you need to remove the side covers of the box, lift it to the top of the frame, focusing on the guide protrusions, drill holes for fastenings, and secure with screws. You can use a screwdriver for this purpose, or you can perform the process manually using a Phillips screwdriver.

Once the box is installed, you need to secure the covers to the sides. After this, you can glue the guide strips to the degreased frame. The guides should be several centimeters below the corner of the bead.

Important nuances

Installation work on window decoration requires certain skills and experience, but if you want to try it yourself, you need to take into account some of the nuances and features of this work.

Installation of blinds begins long before preparing the working surface and a set of tools.

The first step of this process– an informed decision regarding the type and variety of blinds, material, color and texture, depending on the functionality of the room. Thus, it is more advisable to choose vertical blinds for the living room that let in light, for the bedroom automatic roller blinds with electric drive made of blackout fabric, and for the kitchen, where cooking smells and food combustion products are constantly in the air, plastic blinds that do not absorb grease and dirt.

Second important point- this is the correct marking. A lot depends on it, including how easy the installation process will be. If all the architectural features of window openings are taken into account by specialists when ordering blinds from them, everything will go easily and smoothly without the help of professional installers.

It is also important to consider whether it will be possible to open the window after installation, how the light protection devices will work, and whether there is a risk of their deformation.

The installation of blinds must be carried out exactly with the markings and subsequent verification of the functionality of the structure. The most important point here is the choice between fastening - with or without drilling.

It is also necessary to provide for the type of control. For low windows, an excellent solution is one of the types of mechanical direction. Magnetic, automatic (electric) control with an electric drive is suitable for roof and inclined windows, windows in the bedroom.

A few years ago, curtains began to be replaced everywhere with blinds. Now they can be found in offices and living spaces, in trading floors and on the windows of cafes and restaurants.

Features of installing blinds

In order for blinds to serve for a long time, you need to be extremely careful when installing them. Only a balanced, competent approach will ensure normal functioning this is enough complex design. But if you understand all the nuances, you can install blinds in place very quickly.

The main thing is not to forget about the features of each design and take everything into account in the assembly. The installation process is influenced by the walls, namely how smooth they are. Any deviations from the correct level, both horizontally and vertically, will lead to significant complications during operation. Therefore, if in your case there are obvious curvatures of the walls, it is better to invite a specialist with experience in resolving such issues.

If you still decide to install blinds on your own, you need to study the available information, delve into all the details, and be patient.

Basic methods of installing blinds

There are four ways to install blinds.

1. Inside the window opening.
2. For each window sash respectively.
3. To the ceiling
4. On the walls.

When choosing an installation method, you should be guided by your preferences. You can decide which method is right for you based on the design of the window. In principle, blinds can be installed on any windows, including attic ones, but the mounting method will have its own characteristics. The sequence of actions will be similar in any case. Installation methods differ from each other only in some small details.

Sequence of actions when installing blinds

Measuring is the first step

First you need to correctly measure the window opening. Each type of installation has its own nuances that must be observed when taking measurements. This must be done in order to navigate the size of the blinds and decide on a suitable design.

Advice! Subtract 2 cm from the resulting dimensions of the window opening if it is decided to attach the blinds directly to the window opening. This technique allows you to accurately determine required size Therefore, in the future you will not have to deal with the problem of too long blinds that rest on the window sill and bend unsightly.

If you decide to attach the blinds with an overlap, you need to add 5 cm on each side in width so that the window is completely closed. The length will depend on your preferences or designer’s advice. It can only be slightly below the window sill, or it can reach the floor. If you plan to attach blinds to each window sash separately, then you need to measure these parts of the window without taking into account the fittings. When taking measurements, you must try to be punctual. Only correct measurements and ideal geometric proportions will give an impeccable appearance and uninterrupted functioning of the blinds in the future. If the measurement reveals the curvature of the window, you should try to adjust the parameters to the correct figure.

Marking - step two

Before installation, mark the fasteners. Since the design of any blinds is geometrically verified, markings must be carried out with millimeter precision; symmetry also matters great importance. While marking, you need to check how the light-protective devices that you have prepared will work. Will it be possible to open and close the window freely after installing them? Having determined where the control cord will be, you need to mark this place and make additional fastening in this area. It is necessary because more pressure will be put on this area.

Installation - step three

Guided by the markings, you need to attach all the existing parts using dowels and screws. They are screwed into the wall or ceiling. The cornice is hung on these screws. It is used to fix runners and slats, which are simply threaded into the prepared cornice. After completion of work, the functionality of the light protection device is checked.

Features of installing blinds on plastic windows

Quite often it is necessary to install blinds on plastic windows. And this is not very simple. In this case, both the blinds themselves and the window can be rendered unusable quite quickly. To avoid unpleasant consequences, all manipulations must be carried out with the utmost caution.

The main subtleties that must be taken into account when working with different types blinds

Vertical blinds

The most popular vertical variety. It is used in offices, public institutions and in a normal home environment. Color variations are limitless, and the ability to combine colors and shapes gives scope to the most daring design ideas. To install vertical blinds, you need to prepare all the necessary elements:

• cornice;
• slats;
• runners;
• chain.

If the window has an unusual format, you should provide a chain of appropriate length so that it looks appropriate and does not limit the functionality of the entire device. Vertical blinds can be mounted to the wall or ceiling. If you decide to mount the device to a wall, you can choose an area just above a window or directly near the ceiling. If you attach the cornice to the ceiling, then you need to choose an area close to the wall surface at a distance slightly greater than the width of the lamella.

When were the blinds purchased? the right size, colors and quality, mark the fastening elements and install them. Once the brackets are installed, the cornice is attached to them. Runners are put on the cornice and slats are hung on them. When hanging the slats, you must follow the order in which they were placed in the packaging.

Finally, you should take care of the weights. This type of blinds cannot function without them. These weights are suspended at the bottom of the device on chains on both sides (inside and outside). All .

Video on m installation of vertical blinds

Horizontal blinds

This type of blinds has not lost its relevance for many years. Plastic devices are used everywhere, because they are so easy to choose by color and size.

Their design features sometimes cause difficulties for beginners, and they cannot install this type of window decoration.

Horizontal blinds are most often installed on the wall, sometimes they are attached directly to the window. They are mounted to the wall if it is necessary to completely decorate the window opening. Attaching to a window means mounting to the sashes; this option does not limit the functionality of the window itself. It can be easily opened and closed without any obstruction.

Self-installation of horizontal blinds includes the same steps as in the case of the vertical variety:

• froze;
• marking;
• cornice fastening;
• installation of blinds.

Recommendations for installing blinds using self-tapping screws

Before you drill a hole, you need to make sure your markings are correct. To do this, the fasteners are inserted into the cornice and pulled by the cord. Let the blinds open all the way. Next, they are brought to the intended mounting location and visually assessed whether the markings are applied correctly and whether the blinds will open evenly if they are mounted as planned. If there are distortions, you need to make more correct marks with a pencil. Then the brackets are removed from the cornice, they are brought to the marks and points are precisely placed in the places where the self-tapping screw will be screwed in.

Videos installing blinds on plastic windows

Advice! It is better to first drill the holes, and then bring the part to this place and attach it. This method ensures that the integrity of the plastic is maintained. After all, screwing a self-tapping screw through fastener often ends with the appearance of cracks.

When the holes are ready, the brackets are screwed to them and the cornice is hung. It is inserted into the fastenings, and then they are closed. Next perform the following steps:

• installing a hook in the control mechanism;
• installing a cane in a hook;
• the tip is attached to the cane;
• installing a bell, securing it with a knot;
• blinds are lowered by a cord;
• installation lower fixation with a self-tapping screw.

In general, installing blinds is not difficult. However, you must comply with all requirements, be careful and careful. You cannot ignore the instructions that come with the purchased blinds.

Video m installation of horizontal blinds

Installation of blinds without drilling

Some types of modern brackets can be attached to the frame without drilling. It is very comfortable. Such blind systems are mounted on brackets using conventional snaps. In this case, they are not only easy to attach, but also easy to remove to wash the window or tidy up the slats themselves. To attach the brackets without drilling, you need to purchase a special variety of these fasteners. L-shaped brackets are needed; they can be easily hooked to the top of the window sash. They can also be easily removed if necessary. But such a bracket cannot be attached to a blind sash; this is only possible with opening sashes.

The L-shaped fastening is considered the most optimal when attaching blinds inside a window opening. It maintains the integrity of the profile, ensures reliable fixation of the blinds, and is easy to put on and take off. Fastening with tape is less thorough. It will last for many years if it is not subjected to excessive stress, but if handled carelessly it can quickly break.

Blinds are the optimal device for providing protection from sunlight. Various design options allow them to be a real decoration of rooms, creating unique style Houses.