Simple instructions for making a drip tip. Do-it-yourself drip tip for an electronic cigarette Drip tip how to make the same ones
Self-winding is an interesting and exciting process, but not mandatory. Today, you can order dozens of ready-made vaping devices through online markets. Therefore, a DIY drip device is suitable mainly for those who prefer to experiment and have their own unique device.
You will need a serviceable evaporator with a base for winding coils. The best option subtank Working with such a database is convenient and, most importantly for a beginner, simple.
Why is it worth spending time winding drip tape?
Homemade dripper has a number of advantages:
Selection of materials
The drip tip consists of a wire and a filter. Cotton wool is easy to find in any specialty store.
By the way, it is better to make a choice in favor of branded vape cotton rather than saving money and buying a pharmacy one. This radically changes the taste.
Available for spiral the following types materials:
Why is it important to consider resistance?
This is the key parameter. When too high voltage and low resistance of the spirals, the device will fail, and the winding will simply burn out or last a short time.
The higher the frequency of the battery, the greater the resistance of the materials.
What types of windings are there?
Before you make a drip yourself, it’s worth studying coils - a type of winding on a spiral. The classification includes the following:
- Standard coil. This is a lot of space between the turns, which allows the liquid to be better absorbed into the cotton. Therefore, a small amount of steam is produced.
- Nanocoil. Helps achieve thick and voluminous vaping. There is a minimum distance between the turns.
- Pigtail. Complex option, created from two windings. If everything is done correctly, the flavor transfer will significantly improve, and the steam will acquire a characteristic thickness.
Winding instructions
The first step is to prepare and clean the atomizer from the old winding. At the same time, the canthal is cleaned, which is easy to do with a regular damp cloth.
The diameter is selected. A screwdriver is selected according to the value. The smaller the diameter, the less resistance. To start with, a 2.5 mm wire will do.
When the spiral is ready, the product is inserted into the hole in the base. The spiral is inserted at the ends, cut with wire cutters and pressed against the screws. The remaining wire is cut off - the winding is almost ready.
Fans of vaping—smoking electronic cigarettes—appreciate the intensity of vapor production. A do-it-yourself drip tip designed for a certain power allows you to satisfy the individual taste of the smoker and create a unique device. You can remake an old atomizer by winding a new spiral, or create a new heating unit from scrap material. At the same time, this will save money: the wire for the spiral costs several times less than ready-made wound heating elements.
Conversion and repair of old drip
Atomizer repair begins with removing the old coil and cleaning the body and stands from soot and dirt. Use a screwdriver to unscrew the screws and remove the burnt parts. The remaining nodes are wiped with a damp cloth.
Making a spiral
Kanthal and nichrome are used for spirals more often than other materials. These types of wire can be purchased at the store; they are easy to wind and can withstand high temperatures.
Before coiling, the wire must be calcined over a fire: after this procedure it will become plastic and pliable.
The internal diameter of the spiral should be within 2.5–3 mm, as in the photo. For winding, you can take a drill with a cylindrical shank and wind the wire onto the smooth part. From available materials, a knitting needle and a nail are suitable.
Some rules should be followed:
- both spirals must be identical;
- adjustment should begin with 5 turns;
- Even sections of wire should be directed in one direction and not touch each other.
The excess ends are cut off after the final installation of the spiral into the drip.
Adjustment
The ends of the new spirals are inserted into the sockets and clamped with screws. After this, the degree of incandescence is checked.
The optimal glow for vaping is dark yellow and evenly distributed. If the last turns are darker, you need to tighten the screws.
If you have a multimeter at home, you can use it to adjust the resistance.
The intensity of evaporation is regulated by the number of turns. If the spiral is red, it needs to be shortened by one turn. The brighter the wire glows, the faster it will burn out. The body of the cigarette and the mouthpiece will become very hot and burn your lips. When the wire is heated in a drip tip until it turns light yellow and white 1-2 turns should be added.
Atomizer assembly
After adjustment, the drip tip is assembled and refilled:
- 1. The free ends of the wire are cut off.
- 2. Cotton wool twisted into a bundle is inserted inside. It should fit tightly into the spiral and touch it only inside the turns.
- 3. The wick is soaked in liquid.
- 4. When blowing from the side, the wick is placed opposite the holes.
The degree of evaporation of the liquid depends on the distance between the turns of the wire: the smaller it is, the weaker the steam is released.
Creating an evaporator from improvised materials
Any vaper can assemble an electronic cigarette from scrap materials. Electrical diagram Connecting to the battery and button is quite simple. Most of It takes time to create the drip. To make it, you can use ready-made drawings with calculations.
Some parts do not need to be machined, but rather use plumbing fittings suitable sizes: locknut, nipple and coupling.
Electronic cigarettes are becoming more and more popular. And this suggests that people are starting to pursue uniqueness in their electronic steam generators.
And if a year ago the creation electronic cigarette with their own hands was due either to the design interest of clever people, or to the lack of finances of the potential vaper, but now it is already a handmade industry for creating unique masterpieces. Today we will look at how to create a drip with your own hands.
Before we create our drip, we need to decide whether our base will be store-bought or home-made. Today we have a homemade page, so we will create the base ourselves. To start the process we will need to take a metal plate from which we will cut a circle.
Best suited for this stainless steel, no more than 1.5 millimeters thick. We take a coin with a face value of 10 rubles and circle it on a metal plate. We mark 2 holes on the drawn coin that will be intended for the racks. We cut out the part and drill holes in it.
For the assembly process we will need the following parts:
- 4 nuts;
- 2 bolts;
- 4 metal washers;
- 2 dielectric washers;
- 2 terminals;
If you don’t know where to get the terminals, then you can get them out of the housing using a regular AA battery. The materials of such a housing are often malleable and a terminal can be easily cut from them.
Schemes, drawings and drawings for making drips.
Let's start assembling
We need to put a dielectric washer, a terminal and a metal washer on the bolt. Next, we need to wrap the leg of the bolt regular thread so as to isolate the bolt from the base. We thread the bolt into our improvised washer so that the bolt does not touch the washer with its thread. WITH reverse side We put a dielectric washer, a metal washer and fix it all with a nut.
After the first assembly phase, we need to check the quality. Do we have any contact between the bolt and the base of our base? A multimeter will help us with this. By placing 1 multimeter probe against the base and the second against the bolt, no changes should occur on the digital display. There is no contact, which means everything is assembled with high quality.
The second phase of assembly will be with the second bolt. Only its installation will be carried out without dielectric washers. We need to make cuts in the bolts on the output side. The depth should be approximately 1.5-2 millimeters. Now you need to insert a spiral into these slots. It is important to note that the slots in the spirals are made in such a way that if a wire is inserted into them, it would pass through both bolts without bending, and pass through the conditional center of the base base.
Installation of the spiral is carried out as follows: a spiral is inserted into the slot and another nut is put on top, which, going down along the thread, tightly presses the spiral to the bolt slot. We do this on both sides.
After this, we solder the wires to the terminals and check our product. If, when voltage is applied, the coil begins to heat up, then everything is done correctly and the base of our drip tip is ready. Now you can install the base into the drip device itself
Finishing the creation
How to make a drip? With the case the situation is a little more simple. Anything that can accommodate our base can be a potential body for a drip device. Today we will use what we found on the balcony - pipe benders, that is, create a device from scrap materials.
An example of a made drip.
We will need:
- Lock-nut.
- coupling
- Nipple.
We will install the base into the locknut so that the wires come out from the side of the small thread, and attach the base itself to the nut cold welding. We will need this to avoid unnecessary mobility of the nodes.
After this, you need to mark 2 holes on the coupling at the bottom and 2 at the top for airflow. We drill and mount it on the nut. We attach the nipple on top. Your drip is ready.
A homemade drip device may not be the pinnacle of engineering, but it will undeniably set you apart from the crowd of vapers. The device of the drip device will always be the same, but in appearance– this could become your strong point. Pour liquid into the drip and show how it works.
Tell me, have you been interested in how to make a drip before? Have you tried to create drips yourself and what has been your experience in creating such devices?
Vaping is already a subculture that is attracting more and more smokers. Sooner or later, any vaper will learn about the ability to wind coils onto an atomizer themselves. But doubts always arise whether this is necessary and whether it would be easier to buy already finished device. On at the moment no need to implement this process. But still, anyone who winds the spirals themselves will receive a number of advantages.
The first thing you will need is an atomizer that has a base for winding coils. You need to carefully decide on the types of databases. They differ from each other in the form of the presence of a tank. Various models do not use the same type. One of the most popular models is the Subtank. Many people prefer to start with it.
Winding the drip yourself has a number of advantages and disadvantages. And it’s worth starting with the positives.
Saving money
Ready-made windings will cost much more than winding yourself. A head for a tank can cost a couple of hundred rubles. With the same money you can buy up to ten meters of kanthal. One spiral requires up to six centimeters of wire. Thus, you can see how significant the difference is.
Materials you know
You always know what material you are using. Different wires have different characteristics. They have to be sorted out and learned by everyone.
Getting the desired steam
When choosing a replacement “head”, the user loses the right large selection. This applies to wire thickness, evaporation areas, and the like. There are a lot of characteristics for a spiral, all of them are important. By doing it yourself, you have the opportunity to achieve good results. This way you can achieve the amount of steam that suits you.
Selecting parts that are not on sale
You always want to try different things. Experiment, so to speak. Not all desired parts are sold in the store. For example, it is not always possible to find flattened claptons.
A large number of instructions
How to wind drip tape? You will never have such a question. It will be before your eyes ready-made example. Information about this is available on forums, video hosting sites, and so on.
Flaws
Cons exist everywhere. Pay attention to them.
Practice and time
It will take a lot of practice to achieve a good result. You won't be able to wind it perfectly the first time. An experienced person spends no more than ten minutes on this. But if you are a beginner, then you may need more time. Replacing other parts - this process can take up to several hours.
Lack of basic knowledge
Not knowing basic things can lead to problems. At a minimum, you will need to know Ohm's law.
Also, if you are careless, there is a high probability of injury. Follow safety precautions.
Materials
There are two most necessary things that a vaper needs besides an atomizer. Wire will serve as an excellent spiral. Cotton wool, in turn, is perfect as a filter. All this taken together will produce the steam you need.
Spiral material
There are several types of materials for spirals.
You should read them carefully:
- Nichrome– low price and excellent delivery options. Comfort is also provided.
- Fechral- the most famous and popular. Similar to the previous one. Characterized by the absence of nickel. For this reason, it costs less and lasts less.
- Stainless steel- Very available material, which will last a long time. Due to the fact that it is inconvenient to wind, it is used very rarely. Now heaters with temperature control have begun to appear. It is possible to work in TC mode.
- Nickel- very expensive material. Rarely used. It is practically not used among beginners.
- Titanium– similar to nickel, but does not emit harmful substances. It is difficult to say whether nickel overheats; this is a highly debated issue. But due to the potential danger, most people switch to titanium.
Material for making wick
The choice of materials for the wick must be approached with great responsibility.
The most common materials used:
- Cotton wool is a very cheap and popular item. You just need to put in uncleaned cotton wool. You can buy it in all pharmacies.
- Japanese cotton is very practical, but relatively expensive. For beginners this can be a problem. It has no aftertaste and is in great demand.
Winding resistance
Resistance is the basis for winding. This indicator depends on the length, thickness and material.
A very common question is how to wind a drip. This will require knowledge of Ohm's laws. Using the battery incorrectly can cause problems. In addition to power, you also need to consider resistance. If winding is incorrect, a mod may be needed. But it is not on sale everywhere. To avoid overheating, batteries are used at high frequency.
Achieving low resistance is very difficult. Various sources will help you with this.
Types of winding
Coils for drippers– it is these details that play a role in the type of winding. Here are the most basic of them:
Nanocoil- a small spiral, the turns of which are located at a short distance. If everything goes well and there is no short circuit, you can create large area heating In this regard, the pair will be larger.
Regular coil– characterized by a large amount of space. There is a lot of space between the turns. Thus, the liquid passes through the filter better. In this case, the pair will be slightly smaller.
Coil braid– a coil, which is made from two windings. This is more of a subtype of spiral. Two wires are intertwined in its center. The flavor and vapor become more intense, but there is a risk of inhaling the liquid. Not suitable for all clears. There are also different sizes.
