• Interior
• Window
• Walls
• Projects
• The buildings

Floor collector module with decentralized hydraulic settings and individual metering (per consumer). Floor unit for apartment-by-apartment metering of thermal energy Why do we need a floor collector module?

(VT.GPM) Floor unit is used in water heating systems apartment buildings for distributing thermal energy to individual consumers and accounting for its consumption (when installing a heat meter). In addition, the module allows for hydraulic linking of consumers among themselves.

Also, the floor unit for apartment-by-apartment heat energy metering allows for service operations: air release, coolant cleaning, drainage and filling the system.

The module is connected to the common distribution pipeline of the heating system (riser), the input location is left (L) or right (R). Horizontal apartment single-pipe and two-pipe systems heating. The diameter of the connection to the risers of heating systems is ¾ or 1”.

Maximum coolant temperature – 95 ˚С, operating pressure– 10 bar.

The unit is supplied assembled; upon special order, the unit can be supplied disassembled for subsequent assembly on site. It can also be equipped with heat meters, pressure gauges and automatic air vents. The assembled units are pressurized with a test pressure of 15 bar.

As related products for the VT.GPM unit, we offer a set of pressure gauges VT.GP.31, automatic air vents VT.GPM.41,.

To fill out an application for the configuration and delivery of a standard/non-standard floor collector unit, you must fill out an order form.

VALTEC floor units are produced Russian production Vesta Regions LLC.
Russia, 142100, Moscow region, Podolsk, st. Sverdlova, 30, bldg. 1.

The collector module MKT SOTIS-Unit is designed to connect consumers to the UUTEM-E metering unit on the floor, control the distribution of coolant between consumers and organize individual metering of heat energy consumption. Depending on the modification, the module can also perform the functions of conditional regulation (limitation) of coolant flow in apartment heating circuits or precise hydraulic balancing of apartment heating circuits.

The collector module is supplied assembled as part of the UUTEM-E metering unit, or as a kit for assembly directly on site. The assembly of the collector module and its installation on the pipeline must be carried out by specialists with the necessary qualifications, in accordance with the drawing given in the Technical Description.

The collector module can be installed on the pipeline in any of two mounting positions: horizontal or vertical.

At horizontal installation collector module, used in most cases, heat meters (heat meters) are located vertically. If heat meters provide the required level of measurement accuracy only when operating in a horizontal position, the collector module must be installed vertically on the pipeline.

The collector module is installed on the pipeline by connecting it to the input module using connecting elements, such as nipples, fittings, connectors with an American union nut, etc. The connections of the collector module with the input module and pipelines of apartment heating circuits are threaded. To seal these connections, use sanitary linen with sealing paste or special plumbing thread. Installation must be carried out using open-end or adjustable wrenches.

The connections between the individual elements of the collector module are threaded and detachable; their installation must be carried out using open-end or adjustable wrenches. Before hydraulic tests heating system requires mandatory tightening of all detachable connections!

One of the effective options for modernizing the heating system, making it more efficient and reliable, is to install a manifold block. A device that replaced traditional designs linear structure, is designed to improve the ease of use and maintainability of the system.

Let’s take a closer look at how a heating collector functions and what installation features should be taken into account.

Thanks to this distribution, each element is properly heated, supplied with a coolant of equal temperature.

The internal diameter of the collector is determined by calculation so that the speed of movement of the coolant inside it is no more than 0.7 m/s

Having reached the battery and given off the heat received during heating, the liquid is directed through another pipe in the opposite direction to the distribution block. There it enters the return comb, from where it is redirected to the heat generator.

Heated floor pipelines are assembled from copper pipes or their plastic analogues, one-piece fittings are used for connections.

Valves are installed in the heating rings, with the help of which they regulate the supply of coolant, and, if necessary, disconnect the “warm floors” from the general heating network.

A “warm floor” manifold is a structure that includes a series of pipe rings, which is laid under the floor covering

Such systems are always equipped with . It is placed in an intermediate collector unit at the entrance to the return pipe.

The number of pipes on the distribution unit depends on the number of rooms connected to one comb.

The number of collector groups is determined based on the length of the circuits. The calculations are based on the ratio in which 120 meters of pipeline are allocated to one collector group.

Type #2 - hydraulic arrow

When installing powerful and extensive heating systems that are designed in residential buildings large area, use distribution manifolds equipped thermohydraulic distributor or hydraulic arrow.

When installing a connecting link, on one side the heating boiler circuit is connected to it, and on the other - radiator heating or "warm floors".

The use of this module provides independent hydraulic adjustment of each apartment on the floor, and individual heat metering. To connect several apartments to the central heating riser, a collector module with a decentralized (separated) hydraulic adjustment and metering system is used.

Each collector outlet is designed to distribute coolant into separate apartment. Installed on each branch shut-off valves, balancing valves and metering devices.

Module manifolds for multi-apartment system have large diameter(1"1/2 and 2" *) and increased center-to-center distance of the outlets (100 mm). For connecting, disconnecting the module and cleaning the coolant, Ball Valves and a mesh filter. A shut-off valve is installed on the manifold ball valve and in addition, there are manual balancing valves on the supply manifold to regulate the coolant flow.

Automatic differential pressure regulators installed on the return manifold outlets work in conjunction with manual ones balancing valves and serve to hydraulically stabilize the system. The module can be equipped with heat metering devices (heat meters), complete with ball valves, or spaces can be provided for subsequent installation of heat meters. Shut-off ball valves with a fitting for temperature sensor. End groups with automatic or manual (on request) air vents and drain ball valves are installed on the supply and return manifolds.

To connect all the components together, threaded nipples and fittings (adapters) are used.

Pipes for connecting heating devices can be different - copper, polymer or multilayer (metal-polymer). For various pipes Appropriate adapters and adapters are used. By agreement with the customer, modules can be equipped with adapters and adapters in production.

Installation of collector modules on site is carried out on brackets on the wall or on a special bus. The modules must be placed in special niches or provided Technical buildings. An important condition is the possibility of access to the collector modules only for service personnel.

* Diameter 2″ upon request (optional)

How and how long to bake beef Baking meat in the oven is popular among housewives. If all the rules are followed, the finished dish is served hot and cold, and slices are made for sandwiches. Beef in the oven will become a dish of the day if you pay attention to preparing the meat for baking. If you don't take into account	Why do the testicles itch and what can you do to get rid of the discomfort? Many men are interested in why their balls begin to itch and how to eliminate this cause. Some believe that this is due to uncomfortable underwear, while others think that it is due to irregular hygiene. One way or another, this problem needs to be solved.
Why do eggs itch? Minced meat for beef and pork cutlets: recipe with photos	Until recently, I prepared cutlets only from homemade minced meat. But just the other day I tried to cook them from a piece of beef tenderloin, and to be honest, I really liked them and my whole family liked them. In order to get cutlets Schemes for launching spacecraft Orbits of artificial Earth satellites